Estate Control Board

The Timer is an OEM part for Whirlpool washing machines. This component is responsible for controlling the various cycles of the washing machine, ensuring that each phase, from washing to rinsing to spinning, occurs at the correct time and duration.

Causes of a bad timer can include electrical faults, wear and tear on the internal mechanisms, or damage due to power surges or moisture exposure. Over time, these issues can interfere with the timer's ability to accurately manage the washing cycles, leading to performance problems.

Symptoms of a bad timer include:

• The washing machine not advancing through cycles
• Incorrect cycle durations
• The machine getting stuck in one part of the cycle
• Unresponsive or erratic timer controls

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This defrost timer cam replaces the plastic cam on a mechanical defrost timer. It restores the timer's changeover between cooling and defrost, helping prevent frost buildup on the evaporator and temperature swings inside the refrigerator.

• Mounts on the timer shaft to actuate the internal switch between cooling and defrost
• Helps resolve issues like heavy frost on the evaporator, warm fresh food section, or a unit stuck in defrost/run
• Corrects timer advancement problems caused by a stripped, cracked, or missing cam
• Typically installed with the defrost timer in the control housing or rear service area

• Disconnect power before servicing
• Access the defrost timer and note the original cam's orientation for reference
• Remove any retainer, pull the old cam straight off, and press the new cam fully onto the shaft without forcing
• Reassemble, then manually advance the timer to confirm it switches modes before restoring power

Restore accurate cycle control with this washer timer. It sequences power to the drive motor, pump, and water inlet valves so the machine fills, washes, drains, and spins at the proper times.

• Advances the cycle through fill, wash, rinse, drain, and spin stages
• Sends power to the motor, pump, and inlet valves in the correct order and duration
• Safe symptoms: washer won't start, won't advance, stops mid-cycle, runs indefinitely, or skips rinse/spin
• Helps when cycles stall or the dial turns without moving the cycle forward

• Unplug the washer before servicing
• Open the control console to access the timer; note or photograph wiring
• Transfer wires one at a time to matching terminals on the new timer
• Reuse your existing knob/dial and mounting hardware; align the timer shaft before tightening

This is a refrigerator control board that can be used to replace a damaged or faulty board in select refrigerators. The control board is used to manage various functions that occur in the refrigerator, including cooling and defrosting. If there is a problem with the board, the refrigerator might not be able to defrost correctly, or it might not stay cool.The control board for the refrigerator tends to last a long time. However, it could eventually wear out and stop working. It could be damaged due to a voltage surge, or it might be a faulty board. Remove and store all food in the refrigerator and unplug it before beginning repairs.This refrigerator control board works with certain models from Kenmore, Whirlpool, KitchenAid, Roper, Estate, Inglis, Crosley, Gladiator, Kirkland, and Maytag. It's sold individually and is a genuine OEM replacement.

This electronic control board is the appliance's main controller. It interprets keypad/sensor inputs and energizes the correct loads so cycles start, run, and finish as selected—restoring reliable operation when the original board fails.

• Coordinates cycle timing and selected options
• Processes signals from user interface controls and sensors
• Switches power to motors, pumps, valves, heaters, or fans via onboard relays
• Typical failure symptoms: no display or response, won't start, cycle won't advance, or recurring error codes

• Disconnect power at the breaker or unplug before servicing
• Use ESD protection and handle the board by its edges
• Document and transfer connectors one-by-one; reuse any mounting hardware as needed
• Follow the service manual for any model-specific programming/calibration or diagnostics after installation

Please Note Mounting holes must be tapped using old screws. If the old screws are damaged beyond use order part number WP3400064

This is the main electronic control board that manages the appliance's user interface and core cycle functions, restoring responsive controls and reliable operation when the original board fails. What it does:

• Processes user input and runs selected cycles; the board coordinates timers, relays, and electronic commands.
• Restores control when buttons, displays, or cycle selection become unresponsive.
• Can resolve erratic operation, unexpected shutdowns, or failure to start when caused by a failed control board.
• Works with the appliance's sensors and power relays to sequence functions safely.

• Disconnect power (unplug or switch off breaker) before any service to avoid shock or damage.
• Handle the board by its edges and avoid touching contacts; use an anti-static strap if available.
• Transfer any mounting brackets, connectors, or user-interface assemblies as needed from the old board.
• After installation, restore power and verify the control responds and cycles run normally.

Restore dependable cycles with this replacement timer. It controls the sequence and duration of each step, sending power to the correct components at the right time so the machine advances smoothly from start to finish. What it does:

• Directs power to components to run each cycle segment in order
• Advances the cycle through preset intervals
• Helps resolve cycles that won't start or won't advance
• Addresses stopping mid-cycle or only running on certain settings
• Can help when the timer dial doesn't move or advances intermittently

• 1 timer

• Disconnect power before servicing; turn off water supply if applicable
• Access the control console; remove the knob/escutcheon if required and unmount the timer
• Transfer wires one at a time to the new timer or use a photo to match positions
• Reassemble and run a short test cycle to proper operation

The OEM Electronic Control Board is an OEM replacement part for Whirlpool dishwashers. It is a circuit board that controls all of the functions of the dishwasher, including the wash cycles, water temperature, and detergent dispensing.

Causes of failure involve damage from liquid intrusion shortening circuits or component deterioration over extended use reducing precision.

Symptoms include:

• Dishwasher fails to start selected cycle
• Lights, displays or programming malfunctions
• No response from control buttons
• Dishwasher appears dead or powerless

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.