Freezer Parts

Restores the finished edge on your refrigerator cabinet and hides gaps. Replaces cracked, broken, or missing corner trim for a cleaner appearance.

Secures interior trim and panels in refrigerators and freezers. Replace when trim becomes loose or rattles. Confirm fit with your model number.

Removable plastic bin that collects and stores ice from your ice maker. Replace if cracked, broken, or missing to restore proper ice storage.

Authentic freezer basket bumper that attaches to baskets to prevent sliding inside the freezer. Replace if broken, cracked, or missing to keep baskets stable.

Replacement control knob for freezer temperature dials. Installs over the thermostat shaft. Needed when original knob is cracked, broken, or worn smooth.

Rubber grommet kit that mounts and cushions the compressor. Replace worn, cracked, or damaged grommets to restore proper support and isolation.

This compressor overload is a thermal/protective device that helps prevent compressor damage by cutting power when the motor overheats or draws excessive current. It restores normal operation once conditions return to safe levels. What it does:

• Protects the refrigerator compressor from overheating and electrical overloads
• Works with the compressor start relay to help the motor start and run properly
• Common symptom linkage: replaces a failed overload when the compressor hums but won't start
• Stops compressor cycling or prevents repeated trips that cause cooling loss

• One compressor overload (single piece as shown)

• Disconnect all power before replacing to avoid shock or injury
• Handle terminals carefully and reconnect matching terminal positions
• Replace only with the same part number or equivalent
• If compressor still won't start after replacing the overload, check the start relay and compressor condition.

This micro switch detects door or lid position and tells the appliance when the door is closed so cycles can start or safety interlocks stay engaged. It restores reliable door sensing and helps prevent operation with the door open. What it does:

• Acts as a position sensor that completes or breaks the control circuit when the door/lid is closed or opened
• Keeps the appliance from starting or continuing a cycle if the door is open (safety interlock)
• Common symptom fix: appliance won't start, stops mid-cycle, or shows door-related error codes
• Small electrical switch designed to mount at the door latch or frame and connect to the appliance wiring harness

• Disconnect power (unplug or shut off breaker) before attempting service
• Access may require removing panels, trim, or the door latch assembly; keep track of screws and fasteners
• Observe wiring orientation and connector positions; replace exactly as removed or tag wires

Replace your refrigerator door gasket to restore an airtight seal, maintain consistent temperature, and improve energy efficiency. Confirm fit with your model.

This left end cap secures the end of a dishwasher rack door assembly, helping keep the rack stable and rollers aligned for smooth operation. It replaces a worn or broken cap to restore proper rack function and fit. What it does

• Covers and protects the outer end of the rack door, preventing exposed edges.
• Holds rollers or hinges in place so the rack slides smoothly.
• Helps keep the rack aligned to prevent catching or uneven movement.
• Common symptom: cracked, missing, or loose end cap causing rack wobble or noisy operation.

• Always disconnect power to the appliance before beginning repairs.
• Usually installs by snapping into place or fastening with the original screws; use basic hand tools.
• Inspect adjacent rollers and mounting hardware while replacing the cap.
• If fit feels tight, avoid forcing parts—verify orientation before final installation.

Black plug button that covers exposed holes or openings in refrigerator doors and panels. Restores a finished look and keeps dirt out of unused mounting holes.

This inner door panel restores the interior surface and structural support for an oven door, helping maintain a proper seal and protecting internal components from heat and debris. It's a direct-replacement exterior/interior panel used during door repair. What it does:

• Replaces a cracked, dented, warped or otherwise damaged inner door panel to restore door rigidity and appearance.
• Protects insulation, wiring and other internal door components from direct contact with cookware, spills and heat.
• Helps maintain an even seal and reduce drafts or heat loss caused by a warped or loose inner panel.
• Stops rattling or vibration caused by loose or broken interior door pieces.

• Disconnect power to the appliance before starting any repair and allow the oven to cool completely.
• Handle panels and any glass carefully; wear cut-resistant gloves and eye protection.
• Installation typically requires removing the door and detaching interior trim and fasteners—keep hardware organized for reassembly.

Threaded insert nut creates secure anchor point in thin metal or plastic panels. Replace worn, stripped, or missing insert nuts to properly mount covers.

0.6 oz. platinum touch-up paint with brush for appliances. Repairs scratches, chips, and gouges on doors, handles, and trim panels. Acrylic formula.

Graphite spray paint for appliance touch-ups. Covers chips, scratches, and scuffs on dryer drums, washer panels, and exterior surfaces. Restore finish.

Pivot point that supports the showcase assembly in your refrigerator. Replace if cracked, broken, or worn to restore proper alignment and stability.