Freezer Parts

This corner cabinet trim replaces a damaged or missing corner finish piece on the appliance cabinet, restoring a clean edge and helping the door and adjacent panels fit correctly. It provides a cosmetically complete appearance. What it does:

• Covers and protects the cabinet corner for a finished look
• Helps maintain proper alignment and spacing at the cabinet corner
• Commonly replaced when cracked, chipped, broken, or missing
• Restores cosmetic appearance and helps prevent exposed sharp edges

• One corner cabinet trim piece

• Turn off and unplug the appliance before accessing trim or removing panels
• Trim may secure with clips, screws, or snap-fit tabs—inspect fasteners and retainers before removal
• Handle edges carefully; use appropriate tools to avoid scratching adjacent surfaces

This adjustable leveling leg replaces a worn or damaged refrigerator foot to restore stable, level support and smooth door operation. Simple height adjustment helps eliminate rocking and keeps the appliance sitting evenly on uneven floors. What it does:

• Supports the appliance weight and lets you fine-tune height for proper leveling
• Compensates for uneven floors to reduce rocking and wobble
• Helps doors seal and align correctly by allowing height adjustment
• Reduces vibration-related noise when the cabinet sits evenly

• One adjustable leveling leg

• Use gloves and eye protection; unplug the appliance and remove food or shelves near the work area before starting
• Tilt or raise the appliance slightly as recommended by the manufacturer to access the leveling leg; support the cabinet securely
• Turn the leg to raise or lower the appliance; check level and door operation, then recheck after the appliance settles
• If the leg threads or mounting hardware are damaged, replace all affected components before returning the appliance to service

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This right-side end cap replaces a worn or broken trim piece to restore a clean fit and finish on the appliance. It secures the outer edge of the assembly and helps keep adjacent components aligned. What it does:

• Covers and protects the outer edge of the assembly to prevent gaps and sharp edges
• Secures trim and helps keep shelves or panels aligned and stable
• Restores appearance when the original cap is cracked, chipped, or missing
• Reduces rattling or movement caused by a loose or damaged end cap

• Installation is typically straightforward; part snaps or screws into place
• Use basic hand tools; keep track of any fasteners for reinstallation
• Inspect mating surfaces for damage and clean before fitting to ensure a secure fit
• If work requires panel removal near electrical or sealed-system components, disconnect power and follow safety instructions in the service manual

This is a right-side tilt-out end cap that replaces a damaged or missing end piece on a refrigerator/freezer tilt-out bin. Restores secure mounting and proper pivoting of the bin for smooth opening and closing. What it does:

• Serves as the right end support for a tilt-out bin, providing the pivot point and cosmetic trim
• Keeps the bin aligned so it opens and closes smoothly
• Replaces cracked, broken, or worn end caps that allow the bin to sag or fall out
• Helps prevent rattling and excessive play of the tilt-out bin

• One right-side tilt-out end cap

• High-level snap-in or screw-mount replacement; remove the bin and follow OEM instructions
• Remove stored items before servicing and support the bin while replacing the cap
• Use basic hand tools; avoid forcing parts to prevent further damage

A small metal clamp that secures the refrigerator's capillary (temperature sensing) tube to the cold control so the thermostat reads temperatures accurately. Replaces worn or missing clamps to keep the sensing tube stable and prevent movement-related issues. What it does:

• Holds the capillary/sensing tube firmly against the cold control or cabinet
• Helps maintain accurate thermostat sensing by preventing tube movement
• Reduces vibration or rattling from a loose sensing tube
• Stops intermittent temperature swings caused by a displaced capillary tube

• Disconnect power before servicing the appliance.
• Handle the capillary tube gently; avoid kinks or sharp bends.
• Install clamp over the tube and secure to the control or bracket using the factory hole or fastener; do not overtighten.

Color: White

This lock assembly secures the appliance door/lid and enables normal cycle starts by engaging the latch. Replaces a worn or broken lock to restore proper door closure and allow the unit to begin and complete cycles reliably. What it does

• Physically latches the door/lid so the appliance can start and run
• Provides the mechanical engagement the control checks before permitting operation
• Common symptom: door won't stay closed or latch does not engage
• Common symptom: appliance won't start, won't advance or shows a door/lock fault

• Disconnect power (and water supply for washers) before beginning any service
• Handle small parts carefully and note their orientation for reassembly
• If wiring is present, disconnect and reconnect matching connectors only; do not force

This motor overload protector helps prevent the dryer motor from overheating by cutting power when excessive current or heat is detected. It restores normal operation when the motor cools or the overload is replaced. What it does:

• Protects the dryer motor from damage by interrupting power during overheating or overcurrent conditions
• Commonly used when the dryer motor won't start, hums but doesn't run, or the motor trips repeatedly
• Works with the motor start system to reduce the risk of burned windings and costly motor failure
• Resets or is replaced to restore normal motor operation after an overload event

• Always unplug the appliance before checking or replacing this part
• Inspect wiring and motor for underlying issues that can cause repeated overloads

A thin replacement hinge shim that helps align and level the appliance door for a proper seal and smooth operation. Restores correct door spacing to reduce rubbing, uneven gaps, or misalignment. What it does:

• Centers and spaces the door at the hinge to correct misalignment and uneven gaps
• Helps doors close evenly and maintain a consistent seal
• Prevents rubbing or catching caused by out-of-position hinges
• Works with the hinge assembly to restore smooth opening and closing

• Disconnect power to the appliance before starting any repairs
• Remove the door or open/secure it to access hinge area
• Slide or position shim between hinge surfaces as shown in OEM instructions; do not force or bend excessively
• Tighten fasteners to secure alignment, then verify door operation and seal

This electrical relay assembly controls power to a major appliance circuit, restoring reliable switching and helping appliances start and run properly. Replace a failed relay to stop intermittent starts, no-start conditions, or unreliable operation. What it does

• Switches electrical power to motors or heating circuits when the appliance control signals for operation
• Commonly fails after arcing or overheating, causing intermittent or no-start symptoms
• May cause a unit to click repeatedly, run intermittently, or fail to power specific functions
• Restores correct electrical switching when installed in place of a damaged relay

• Disconnect power before accessing control panels or wiring to avoid shock
• Access and removal typically require removing the control panel or top panel; keep track of screws and wire locations
• Replace with the exact part number and reconnect all terminals securely; do not bend or damage connector pins

This door hinge secures and allows smooth pivoting of a refrigerator door so it opens and closes correctly. It restores proper door alignment and helps maintain a tight seal to preserve cooling performance. What it does:

• Supports the weight of the door and provides a stable pivot point
• Keeps the door aligned to prevent rubbing, gaps, or uneven closing
• Helps the door seal fully to prevent warm air leaks and temperature loss
• Commonly replaced when the door sags, sticks, or makes noise during operation

• One door hinge assembly

• Disconnect power to the appliance before beginning any repair
• Support the door while removing and installing the hinge to prevent injury or damage
• Use factory mounting hardware; tighten fasteners securely but avoid over-torquing
• Check hinge pins and mounting surfaces for wear

Nickel