Freezer Parts

This mounting bracket secures internal components and panels to restore proper alignment and reduce vibration. It provides a direct replacement for worn or damaged support hardware so assemblies stay firmly in place. What it does:

• Secures appliance panels or internal components to the cabinet or frame
• Keeps parts aligned to prevent rattling, vibration, or movement during operation
• Restores proper fit where a bent, broken, or missing bracket causes loose assemblies
• Helps maintain safe, stable operation by holding parts in their designed position

• One mounting bracket

• Designed to replace the factory bracket in the same mounting location; verify fit before installation
• Use appropriate fasteners and torque to avoid striping or damage to mounting points
• Disconnect power and empty unit if needed before accessing internal areas

This compressor grommet is a rubber mounting isolator that cushions and secures the compressor to the appliance chassis, helping reduce vibration and noise while preventing metal-to-metal contact and premature wear. What it does:

• Cushions compressor movement to reduce vibration transmitted to the cabinet
• Dampens noise and rattling caused by compressor operation
• Prevents direct metal-to-metal contact that can wear mounting points
• Helps keep the compressor positioned and secured under load

• Disconnect power to the appliance before accessing the compressor or base pan
• Replace grommets while supporting the compressor to avoid strain on lines and connections
• Inspect remaining mounting grommets; replace all worn isolators for best performance

This left-side tiltout end cap replaces the damaged or worn plastic end piece that secures and guides a fridge/freezer tilt-out or dairy bin. Restores a secure fit and smooth opening for the tilt-out assembly. What it does:

• Replaces the left end cap on a tilt-out/dairy bin assembly
• Helps keep the drawer aligned and held in place during use
• Reduces rattling or catching when opening and closing the tilt-out
• Matches OEM fit and mounting points for direct replacement

• One left tiltout end cap

• Remove contents and the tilt-out bin before attempting replacement
• Installation typically requires basic hand tools and gentle prying to disengage clips
• Inspect mating clips and housing; replace or repair any broken tabs before reinstalling

This inner door panel for the freezer provides the interior surface and structural backing for the freezer door, restoring a clean appearance and proper support for the door liner and components. What it does:

• Replaces a cracked, dented, or warped freezer inner door surface
• Restores the interior mounting surface for bins, shelves, and the door liner
• Helps maintain a proper door seal by giving the gasket a solid backing
• Prevents exposed insulation and reduces the risk of cold air loss or moisture buildup

• Disconnect power to the appliance before starting repair
• Door removal is commonly required; support the door and follow OEM instructions
• Transfer any handles, brackets, or gaskets from the old panel to the new one if needed
• Use correct fasteners and do not overtighten; check door alignment and seal after reassembly

This is a replacement retainer clip used to secure interior trim and small components on compatible refrigerators. It restores proper fit and prevents loose panels, rattles, or improperly seated trim. What it does:

• Secures trim, panels or small components in place to maintain proper alignment
• Prevents rattling, gaps, and shifting caused by broken or missing clips
• Replaces brittle or cracked clips that no longer hold parts securely
• Helps restore a clean, finished fit where the original clip has failed

• Disconnect power to the appliance before beginning any service
• Remove surrounding trim or panels carefully to access clip location; small fasteners may be present
• Press replacement clip into position until it snaps in; do not force or bend brittle plastic
• If other clips or fasteners are damaged, replace them to ensure a secure fit

A replacement temperature control (thermostat) that regulates the refrigerator/freezer cooling cycle so food stays at the set temperature. Restores reliable on/off cycling when the original control fails. What it does

• Sends the signal to the compressor and fans to maintain the selected interior temperature.
• Replaces a faulty control when the appliance is too warm or too cold, or when temperatures fluctuate.
• Can stop short-cycling or continuous-run issues caused by a defective control.
• Works with the fridge's user temperature selector to restore normal cooling responses.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle control and wiring harness carefully; note or label wire locations before removal.
• Mount the control in the original position and reconnect wires to the matching terminals.

This rotary defrost timer controls the refrigerator's switch between cooling and defrost cycles to help prevent frost buildup and maintain proper cooling performance. It replaces a failed or intermittent defrost timer to restore automatic defrost operation. What it does:

• Advances the refrigerator between cooling and defrost modes on a timed cycle
• Ensures the defrost heater runs at scheduled intervals to melt frost and ice
• Commonly replaces timers that fail to advance, stop, or cause continuous cooling
• Helps address symptoms like excessive frost, warm compartments, or continuous compressor run

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access and mounting vary by model;
• Verify electrical connections and timer orientation match original before reassembly
• Consider replacing with an exact OEM part number for fit and function

This hinge-side door stop helps limit door travel and protect the hinge assembly from over-rotation for a secure, consistent door movement. Replaces a worn or broken hinge-side stopper to restore proper door alignment and operation. What it does:

• Acts as the stop/breaker on the hinge side to prevent the door from swinging past its intended range
• Helps reduce stress and wear on the hinge and door seal caused by over-rotation
• Commonly replaced when the door catches, over-rotates, or the hinge feels loose
• Works with the hinge assembly to keep door movement smooth and predictable

• Disconnect power to the appliance before starting any repair
• Remove the door or access hinge per your model's service instructions to reach the stopper
• Inspect adjacent hinge hardware and fasteners; replace any stripped or damaged parts
• Use proper hand tools and follow manufacturer torque and alignment guidance