Parts for Ge MSH22GRTAAA: 02 - Freezer Section Parts

This breaker strip trim installs along the freezer section edge of your refrigerator. Replace if cracked, broken, or missing to restore appearance.

Breaker strip trim for top freezer compartment door. Replace if cracked, broken, or missing to restore door seal and cabinet finish appearance.

This shelf support secures an interior refrigerator shelf in place so food items stay level and storage remains organized. It replaces a cracked or worn support to restore proper shelf seating and stability. What it does

• Holds a refrigerator shelf or shelf trim in the correct position to prevent sagging or tipping
• Restores stable support for glass or wire shelving that no longer stays seated
• Helps eliminate shelf movement that can cause items to slide or spill
• Works where a broken, chipped, or missing support prevents proper shelf alignment

• Disconnect power to the appliance before starting any repair and empty the shelf area
• Remove the affected shelf or trim to access the support; reinstall shelf to confirm correct seating
• Use basic hand tools as needed and avoid forcing parts to prevent further damage
• Replace all affected pieces for consistent shelf alignment

Refrigerator not cooling but freezer works? Frost buildup on back wall? Your evaporator may need replacement. Moderate difficulty repair for most models.

Freezer icing up or fridge too warm? Your defrost heater melts frost on evaporator coils. DIYers report 10-30 minute installs with a screwdriver.

Fridge not cooling but freezer works? Ice buildup on evaporator coils? This defrost thermostat regulates defrost cycles. Easy 5-15 minute DIY fix.

Replaces broken or worn lower door hinge assembly on your refrigerator. Restores proper door alignment and smooth pivot action. Includes cams for installation.

Replacement roller wheel for refrigerator drawers and bins. Installs on rear guide rails. Replace when worn, cracked, or causing sticking movement.

Wire harness for refrigerators. Connects electrical components inside the unit. Replace if wires are frayed, damaged, or connections are loose or corroded.

Replaces the outer housing that supports your refrigerator's ice crusher and dispenser chute. Order a new housing if yours is cracked or broken.

Pack of 12 washers for refrigerator ice crusher auger assembly. Replace worn, cracked, or missing washers during ice maker repairs and maintenance.

E-style retainer ring secures ice maker auger components. Replace when worn or damaged to restore ice dispensing. Confirm fit with your model number.

Replacement pivot that supports and aligns refrigerator doors or drawers. Needed when original pivot is cracked, broken, or worn, causing misalignment.

This replacement part is an ice dispenser deflector, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. Ice dispenser deflectors are found inside of the ice-making assembly and are an important part of many freezers. The ice dispenser deflector allows the ice to come down from the tray into the dispensing area. A new ice dispenser deflector might be needed if the current one has become too brittle and has even cracked or broken. Be sure that the refrigerator is completely powered off before starting this repair. The user must have access to the ice maker assembly and will need common household tools like a screwdriver and pliers. The user might also need working gloves as some parts in and around the assembly have sharp edges or blades.Note that this part is sold individually. This ice dispenser deflector is sourced directly from the manufacturer and is a genuine OEM replacement part.

Ice not dispensing or jamming? This ice dispenser auger blade moves ice from the bin to the chute. Installs in numbered sequence with spacers.

Fix ice dispensing issues with this refrigerator auger blade. Solves crushed ice not dispensing or jamming problems. Moderately easy DIY repair part.

Ice won't crush and gets stuck between blades? This moving dispenser blade restores crushing function. Simple DIY fix for side-by-side refrigerators.

Mounting spacer maintains proper clearance between refrigerator panels, doors, or components. Replace if cracked, broken, or missing to restore fit.

Supports and centers the ice crusher blade assembly in your refrigerator. Replace if cracked, worn, or missing to prevent blade wobble and noise.

Ice not dispensing or auger jammed? This rear ice dispenser helix connects the motor to the crusher blade. Moderately easy DIY fix for most models.

This replacement part is an ice auger blade, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. Ice auger blades are usually found in ice maker assemblies and are used during the ice-making and dispensing process. These blades are what are used when the user is in need of shaved or crushed ice. The mechanism takes full ice cubes and cuts the ice cubes down to create the different types of ice. A new ice auger blade might be needed if the user noticed that the current blades are dull or unable to cut ice. It is possible that the blades become dull over time after many years of use, so replacing them might be a good idea. Be sure the power is completely off before attempting to repair this part.This ice auger blade is sourced directly from the manufacturer and is a genuine OEM replacement part. Note that this part is sold individually.

The Drive Cup is an OEM part for GE refrigerators. This part engages with other parts to drive the ice out of the molds and into the storage bin.  

Causes of Drive Cup failure can range from physical wear and tear from regular use, which may lead to cracks or deformities in the part, to accumulation of frost or ice that hinders its movement.  

Symptoms of a malfunctioning Drive Cup include:

• The ice maker fails to eject ice properly, leading to clogs or jams within the system.
• Unusual noises during the ice-making cycle, which could indicate that the drive cup is not engaging correctly with other components.
• Decreased efficiency in ice production, as the mechanism struggles to operate smoothly.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Includes ice auger blade. For blade separately use WR2X7783. Please note Due to manufacturer changes they no longer make the auger as shown (helix coil approx 7 1/2") in the photo. The replacement helix coil is now approx. 5". If you have the original as shown in the photo you must order the complete auger/bucket assembly.

This is the ice container only.

Ice not dispensing or slow ice flow? This ice bucket and auger assembly stores and moves ice to your dispenser. Simple DIY install in 10-30 minutes.

Seals the ice bucket to prevent spills, frost buildup, and water pooling. Replace when ice shifts or water collects. Confirm fit with your model.

This part has been discontinued and is no longer available.

Includes 12 clips.

Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.

Ice dispenser not working or making humming noise? This auger motor drives the crusher mechanism to feed ice through the chute. Moderate DIY repair.

Drives the auger to push ice from bin to chute. Replace if ice won't dispense or motor jams. Verify fit with your model number before ordering.

Wire harness for refrigerators. Connects electrical components inside the appliance. Replace if wires are frayed, damaged, or connections are loose.

This part has been discontinued by the manufacturer and is no longer available.

Mounting bracket that secures the ice dispenser solenoid in place. Replace if cracked, broken, or missing to restore proper solenoid alignment and function.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Ice dispenser only making crushed ice instead of cubes? This solenoid valve kit fixes the cube/crushed ice selector. Easy DIY repair with video guide.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.

Replacement ice bucket door for refrigerators. Covers the ice storage bin opening. Order when your original door is cracked, broken, or missing.

Refrigerator light not working or flickering? A faulty light socket often causes this. Simple plug-in repair with no tools required. Video guide available.

Replaces dim, flickering, or burnt-out bulbs in refrigerators, ovens, and microwaves. Restores interior lighting for visibility. Verify fit with model.

Package of 12

Mounting screw for securing range components and panels. Replace if missing, stripped, or corroded. Package includes 12 screws for installation.

Freezer light not turning on or off? This door light switch activates interior lighting when opened. Moderate DIY repair—press tab, rotate out old switch.

The Evaporator Fan Motor Kit is an OEM part compatible with GE refrigerators. It is a critical component responsible for circulating air and maintaining proper airflow within the refrigerator's evaporator system, ensuring efficient cooling and temperature regulation. It features a shaft that measures 3/8 of an inch and two right-side terminals. Notably, the motor no longer comes with harness wires, which must be obtained separately for installation.

Symptoms of a faulty evaporator fan motor include:

• Inconsistent or inadequate cooling in the refrigerator or freezer compartments
• Warm spots or temperature fluctuations within the refrigerator
• Excessive frost buildup or ice accumulation in the freezer

Causes of a bad evaporator fan motor can include wear and tear over time, electrical issues or short circuits, or physical damage from foreign objects or improper maintenance.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models. 

Freezer not cooling or making buzzing noise? The evaporator fan blade circulates cold air. Easy DIY fix in under 5 minutes—simply pull off and press on.

The Fan Blade Grommet is an OEM replacement part for GE brand refrigerators. Located behind the evaporator fan blade where its central shaft passes through, this rubber sealing piece creates a protective barrier isolating the fan assembly.

Causes of a potentially problematic fan blade grommet include cracks or deterioration that develop from continuous vibration and impacts over extended use. Exposure to temperature fluctuations can also cause the rubber to harden and lose elasticity. 

Symptoms of a faulty fan blade grommet include:

• Airflow obstructions within the duct 
• Noisy vibrations from the fan assembly
• Rubber debris collecting on components

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore model refrigerators.

Ice maker not producing ice or stopped working? This ice maker kit restores ice production. Includes full assembly for harvesting and ejecting ice.