Dishwasher Bracket & Flange

The Dishwasher Installation Bracket Kit is an OEM part for LG dishwashers. This kit includes brackets that secure the dishwasher to the countertop, cabinetry, or floor, ensuring it remains stable during operation. Proper installation of these brackets is essential for preventing excessive movement and vibration during the dishwashing cycle.

Over time, installation brackets can become loose or damaged due to constant vibrations, improper installation, or accidental impacts. If the brackets are compromised, the dishwasher may not be securely anchored, leading to various operational issues.

Symptoms of a bad installation bracket kit include:

• The dishwasher moving or shifting during operation
• Increased noise and vibration levels
• Difficulty in keeping the dishwasher level
• The dishwasher door not closing properly

This OEM LG part is also compatible with Sears/Kenmore.

The Hinge Brace is an OEM replacement part for Whirlpool dishwashers. It serves as a supportive bracket anchoring the dishwasher door hinge assembly firmly in place.Note: This part may be different from your original. If your original part was a flat plastic vapor barrier, the new design is a wire. It is a factory design change, the old design is no longer available.

Over time, the hinge brace can degrade due to constant use, heavy loads on the door, or accidental impacts. A faulty hinge brace can result in misalignment or difficulty in operating the dishwasher door.

Symptoms of a bad hinge brace include:

• Loose or unstable door that does not close securely
• Gaps appearing around the door seal during wash cycles
• Broken hinge components from added stress and tension on the door
• Difficulty fully opening or closing the dishwasher door

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This dishwasher rack tine row bracket secures the fold-down tine row to the rack so it pivots and locks correctly. Replacing a cracked or missing bracket helps restore stable plate support and smooth loading.

• Secures the fold-down tine row to the dishrack
• Allows the tine row to pivot between upright and flat positions
• Helps keep dishes from tipping during cycles
• Common symptoms: tines won't stay up, row flops loosely, bracket is cracked/missing

• Disconnect power to the dishwasher before servicing
• Pull out the rack and locate the affected fold-down tine row
• Release the old bracket and snap the new bracket onto the rack wires
• Verify the tine row pivots and latches smoothly before returning the rack

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

This replacement switch leaf is the small metal contact that completes a switch circuit when actuated, restoring reliable electrical contact and helping return normal operation to the affected control or component. Easy-to-replace individual contact for switch assemblies. What it does:

• Serves as the conductive contact inside a switch assembly to open and close an electrical circuit
• Engages with the switch actuator to make or break power to a component
• Common symptom link: intermittent or failed operation of the circuit the switch controls (flickering, no power, or inconsistent response)
• Small, replaceable part used when the original contact is worn, bent, or corroded

• Disconnect power to the appliance before beginning any repair
• Handle the contact by the edges; avoid bending or contaminating the mating surfaces
• Inspect the surrounding switch housing; replace the full switch assembly if the housing or actuator is damaged
• Reassemble and test the switch operation after installation

The Mounting Bracket is an OEM part for Frigidaire dishwashers. It is a metal component that secures the dishwasher to the surrounding cabinetry. The mounting bracket provides structural support and stability during operation.

Causes of a bad mounting bracket can include damage from installation/removal, cracks or deformities from heavy loads, or broken welds/fasteners holding it in place.

Symptoms of issues with the mounting bracket include:  

• Excessive vibration or shaking of the dishwasher during cycles
• The unit not sitting level or secured properly in the space
• Noises related to movement that shouldn't occur
• Visible damage or instability of the unit 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

Replacement bracket that secures the flood/leak detection switch inside the appliance, keeping the switch positioned to sense unwanted water and help the leak-detection system work as intended. What it does:

• Holds the flood/leak switch in the correct position so it can detect water accumulation.
• Ensures consistent switch activation when water pools under the cabinet or base pan.
• Common repair when you find water under the appliance, persistent leaks, or when leak detection isn't responding.
• Simple, passive mounting part—no electrical function.

• Disconnect power and shut off the water supply before accessing the appliance.
• Remove the appropriate access panels to reach the bracket location; note orientation of the switch before removing.
• Reinstall bracket using the original fasteners or equivalent screws; keep parts organized during disassembly.
• Restore power/water and test the appliance for proper leak-detection operation after reassembly.

If looking for the two wheel guide rail bracket order WD12X10221

This hinge bracket secures the appliance door to the cabinet and provides a stable pivot point for smooth opening and closing. Replaces a worn or broken bracket to restore proper door alignment and sealing. What it does:

• Supports and locates the door hinge so the door pivots correctly.
• Restores proper door alignment and helps the door close and latch securely.
• Stops sagging, uneven gaps, or scraping caused by a damaged bracket.
• Works as the mounting point for hinge pin hardware.

• One hinge bracket

• Disconnect power (and water supply if applicable) before starting any repair.
• Support the door during removal to prevent it from dropping; two-person lift may be required for heavier doors.
• Retain or reuse original hinge pins, screws, and shims unless replacements are specified.

This thermostat bracket holds the oven or range thermostat securely in place, ensuring accurate temperature sensing and stable oven performance. Replaces a worn or broken bracket to restore proper thermostat positioning. What it does:

• Secures the thermostat assembly to the oven/range interior so the thermostat bulb or probe senses temperature correctly
• Prevents the thermostat from shifting or contacting heating elements
• Commonly replaced when the bracket is cracked, bent, or missing and causes temperature or control issues
• Helps reduce temperature inconsistencies caused by a loose or damaged mounting

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Handle the thermostat and sensor bulb carefully; avoid kinks or direct pressure on sensing elements
• Basic hand tools are typically required; verify part alignment before tightening fasteners

This left switch breakwater is a small plastic retainer that holds the console switch assembly in place, keeping switches secure and aligned for reliable control operation. It helps restore proper switch positioning after damage or wear. What it does:

• Secures the left console switch assembly so buttons and selectors operate correctly
• Keeps the switch contacts aligned to prevent intermittent or non-responsive controls
• Helps block debris from interfering with the switch mechanism
• Commonly replaced when the switch feels loose, sticks, or the control behaves inconsistently

• One left switch breakwater

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the control console or panel; follow your model's service instructions
• Handle plastic retainers carefully to avoid cracking; replace if damaged

This is the front corner block. For rear corner block use 00263093.