Frigidaire Dishwasher Panel Parts

The Toeplate is an OEM part for Frigidaire dishwashers, specifically designed to fit seamlessly at the bottom of your appliance. This toeplate not only enhances the aesthetic appeal of your dishwasher by hiding the space beneath the appliance but also serves as a protective barrier, preventing debris from getting under the dishwasher.

Causes of a bad toeplate include physical damage such as dents, cracks, or warping, often resulting from accidental kicks or impacts. Additionally, improper installation can lead to a loose or misaligned toeplate, which may compromise its functionality and appearance.

Symptoms of a bad toeplate include:

• Visible damage or deformation.
• Difficulty in fitting or securing the toeplate to the dishwasher.
• Increased noise or vibration due to lack of insulation or support.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Console Assembly is an OEM part for Frigidaire dishwashers. As the control interface, it houses buttons and lights to program wash cycles and monitor status. The assembly covers and protects internal control boards.

Symptoms of a bad console assembly include:

• Non-functioning or unresponsive buttons  
• Water intrusion behind surfaces
• Cracks, chips, or clouding that compromise appearance
• Inability to power on the dishwasher

Causes can be normal wear and tear over time, accidental impact damage, or moisture-related issues. Periodic cleaning helps prevent deterioration. 

This OEM Frigidaire replacement console assembly is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore branded dishwashers. 

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

This replacement dishwasher door forms the hinged front of the tub. Replacing a bent or damaged door restores proper alignment and latching so cycles can run correctly and the wash chamber remains properly contained.

• Creates the front barrier of the wash chamber and supports the latch/handle area
• Aligns with the door gasket to promote a proper seal
• Restores correct closing and latching so the cycle can start
• Common symptoms: difficulty closing, cycle won't start due to door not latching, visible dents/warping, poor seal along the gasket

• Disconnect power and turn off the water supply before servicing
• Support the door and carefully relieve hinge spring tension during removal
• Transfer any reusable components from the old door to the new one as needed
• Run a test cycle to ensure proper latching

This inner door assembly replaces the damaged or cracked inner panel on your refrigerator/freezer door to restore a clean interior surface and proper component mounting. It's the factory-style inner panel used behind the outer door skin. What it does:

• Forms the interior surface of the door and provides mounting points for bins, shelves, and hardware
• Restores a smooth, sanitary interior when the original panel is cracked, warped, or separated
• Helps keep door components aligned to prevent rattling or improper sealing
• Compatible with OEM door hardware and trim when original mounting points are intact

• Installation requires removing the door and outer door trim; handle screws and wiring may need to be disconnected
• Inspect and transfer any clips, gaskets, bins, or fasteners from the old panel
• Use proper support to avoid dropping the door; get a helper for safe handling of heavy doors
• Disconnect power and follow manufacturer safety instructions before servicing

This kickplate (toe plate) replaces the lower front trim on compatible refrigerators to restore appearance and protect the cabinet base from scuffs and drafts. Durable sheet-metal construction keeps the front edge looking clean. What it does:

• Covers and protects the refrigerator's lower front area from kicks, scuffs and dirt.
• Restores a secure trim piece when the original is bent, dented or loose.
• Helps reduce visible gaps at the cabinet base for a neater fit.
• Improves appliance appearance after damage or during refurbishment.

• Disconnect power to the appliance or follow the manufacturer's safety guidance before beginning work.
• Remove the old kickplate by loosening the retaining screws or clips; lift out and set aside.
• Align the replacement plate, engage any clips or tabs, and reinstall screws; avoid overtightening.

This outer refrigerator door restores the appliance's exterior and helps maintain proper sealing and temperature control. It replaces a cracked, dented, or damaged door to improve appearance and function. What it does

• Replaces a damaged outer door panel so the fridge can close properly and look like new
• Helps maintain an effective seal when used with an intact gasket, reducing cold air loss
• Stops drafts and visible damage that can lead to higher energy use or interior moisture
• Works with existing hinges and trim when the correct hardware is transferred

• Disconnect power to the appliance before starting and remove food from door shelves as needed
• Transfer existing hinge assemblies, handles, trim, and gasket to the new door unless this part specifically includes them
• Use caution when lifting and aligning the door to avoid chipping paint or damaging the hinge pins
• If you see missing or damaged hardware, get the required screws/hinges separately.

Color: Stainless

Color: White

Color: Black