Frigidaire Range Control Board

This main control board is the electronic module that manages your appliance's functions and user inputs, restoring normal operation when the board has failed. It replaces the appliance's primary logic/control circuit to allow proper control of cycles and features. What it does

• Interprets control panel commands and runs the appliance's programmed cycles
• Manages timing, sensors, and power distribution to subsystems
• Can resolve symptoms like unresponsive controls, erratic operation, or failure to start when the board is the fault
• Works with door, temperature, and user-interface signals to coordinate appliance functions

• One main electronic control board

• Disconnect power before attempting replacement to avoid shock or damage
• Handle the board by edges and avoid touching circuits or components
• Verify connectors and mating harnesses are fully seated during reassembly

This electronic control is the appliance's main user interface and logic board that manages cycles, display functions, and timed operations, restoring normal control when the original board fails. What it does:

• Interprets user inputs from the console and runs appliance cycles
• Controls timers, displays, and other electronic functions
• Stops proper operation when the board fails, which can cause unresponsive buttons or blank/missing display
• Can resolve issues like intermittent operation, incorrect cycle behavior, or failure to start when faulty

• Disconnect power to the appliance before starting any work to avoid shock hazard
• Handle the board carefully; avoid touching circuit traces and connector pins
• Reconnect all wire harnesses in the same positions and secure mounting fasteners

This user interface board replaces the front control module that registers your button presses and displays oven settings, restoring reliable input and accurate status feedback on compatible ranges and ovens. What it does:

• Receives touchpad/button inputs and sends commands to the main control board
• Drives the display and status indicators so settings and temperatures are visible
• Resolves symptoms like unresponsive buttons, missing or garbled display, or intermittent control behavior
• Works with the range/oven control system to select modes, set timers, and start/stop cycles

• Disconnect power at the breaker before beginning service to avoid shock or injury
• Handle the board by the edges and avoid static discharge; use a grounded strap if available
• Check and reseat harness connectors; ensure mating connectors are clean and fully engaged
• Some repairs require removing the oven control panel or door—retain screws and note component placement during disassembly

This electronic control board manages the refrigerator's user interface and timing functions so the appliance runs its cycles correctly. Replacing a faulty board restores control of temperature, lights, and automatic cycles. What it does

• Receives user inputs and sends control signals to compressors, fans, lights and defrost systems
• Manages timing and cycle operation for cooling and defrost
• Commonly linked to symptoms like unresponsive controls, error codes or a blank display
• Can cause intermittent cooling, lights or dispenser functions to fail when defective

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the board by the edges and avoid static discharge; use an ESD strap if available
• Some installations require removing control housing or trim; keep track of screws and connectors and test functions after reassembly

This is a genuine OEM manufactured controller for ovens and ranges that has been sourced directly from the manufacturer. This part is made by Frigidaire and is intended to replace a controller that has been broken or rendered ineffective. In order to safely and properly work the oven, the controller needs to be in working order, as it controls the temperature and oven settings. Over time, the user may find the controller becomes worn, warped, corroded, cracked, or otherwise broken, requiring replacement. When undergoing any sort of repair work, the power supply should always be entirely disconnected. It is highly recommended that work gloves are worn for protection.This controller is sold individually and is made from high-quality, durable, non-corrosive materials. It is an authentic replacement part and is suitable for use on a wide variety of ovens and ranges that have been manufactured by Frigidaire, Electrolux, Kelvinator, Westinghouse, and other brands.

This electronic clock timer replaces the oven control module that displays time and manages timed cooking functions, helping restore accurate timekeeping and scheduled bake/clean operations. What it does:

• Displays oven time and timer countdowns so you can monitor cooking at a glance
• Controls timed cooking and delayed-start settings (when supported by the oven)
• Restores user interface responsiveness for clock and timer features

• One clock timer (electronic oven control) assembly

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the display/faceplate carefully to avoid scratching or cracking the lens
• Some models require removing the console or rear access panel and unplugging a wiring harness

This electronic control board is the refrigerator's main control module that manages cooling cycles and user commands, restoring normal operation when the original control fails. Replaces a failed control to help the appliance respond correctly to temperature and mode settings. What it does:

• Receives input from the user interface and sensors to control compressor, fans, and defrost cycles
• Regulates timed operations and temperature setpoints for consistent cooling
• Works with the appliance's sensor and relay systems to coordinate defrost and compressor run cycles

• 1 electronic control board (main control)

• Disconnect power before accessing the control to avoid shock or damage
• Handle the board by edges and avoid touching circuit components or connector pins
• Verify connector seating and mounting before restoring power; ensure correct board orientation

This electronic clock timer assembly controls the oven's timekeeping and timed cooking functions while providing the front-panel time display. It restores timed bake/clean features and visible clock readout for normal oven operation. What it does:

• Maintains and displays the oven clock so the control shows correct time.
• Enables timed bake, delay start and automatic shutoff features when used by the oven controls.
• Interfaces with the oven control panel to start/stop timed cycles.
• Prevents timed or delay cooking if the clock/timer fails or shows no display.

• One clock timer assembly (single unit as shown).

• Disconnect power to the appliance before inspecting or replacing the clock/timer.
• Access typically requires removing the control panel; handle the control and display lens carefully to avoid damage.
• Use the oven's service manual for disassembly and wiring reference; verify wire routing and connector seating during reassembly.

This user interface control board kit replaces the front console electronics that let you select cycles, adjust settings, and display status. Restores control panel responsiveness and visible status indicators for affected units. What it does:

• Replaces the touchpad/PCB assembly that registers button presses and communicates with the main control board
• Restores displayed cycle, temperature, and timer readouts when the original panel fails
• Helps resolve unresponsive buttons, incorrect or blank displays, and intermittent control behavior
• Works with the appliance's main control to accept user inputs and send commands

• Disconnect power to the appliance before starting to avoid shock or damage
• Follow OEM disassembly steps for access to the front console; handle circuit boards by the edges
• Keep screws and trim organized; verify connector orientation before reconnecting

A replacement clock timer console assembly that restores the oven or range clock display and timer functions so you can set cook times, use the kitchen timer, and see the current time on the control panel. What it does

• Replaces the control console that displays the clock and manages the countdown/timer functions.
• Restores visible timekeeping when the display is blank, dim, or non-responsive.
• Enables timer alarms and timed cook functions to work correctly.
• Useful when touchpad keys for clock/timer no longer register.

• One clock timer console assembly.

• Disconnect power to the appliance at the breaker or unplug before servicing.
• Remove the control panel trim or back cover to access the console; keep all screws and fasteners for reassembly.
• Handle the display assembly carefully to avoid damaging the lens or ribbon connectors.

This electronic clock timer replaces the oven control that manages bake/clean cycles, the digital clock, and the kitchen-timer functions so you can set time and timed cooking features reliably. What it does:

• Provides the digital clock display and kitchen-timer functions for the oven
• Controls timed bake and self-clean cycles when used with the oven control board
• Restores responsive keypad/display when the original clock fails or shows blank/erratic time
• Helps resolve symptoms like no clock display, unresponsive timer buttons, or oven timer not counting down

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle the control and display window carefully to avoid scratching; keep small hardware and connectors together
• Match connector harness and align mounting tabs; do not force the unit into place
• Restore power and verify clock, timer, and timed cooking functions before finishing reassembly

This electronic clock timer replaces a failed oven/range clock to restore time display and timed baking functions. It gives a visible clock and lets the oven use timed cook and delay-start features. What it does:

• Displays oven clock time and provides countdown/count-up timer functions
• Enables timed baking, delay start, and auto-off features controlled by the range
• Commonly replaces units showing a blank display, incorrect time, or unresponsive timer controls
• Works as the control interface for oven clock-related functions

• One clock timer assembly

• Disconnect power to the appliance before accessing the control panel to avoid shock
• Handle the display and ribbon/plug connectors gently; align connectors fully during reassembly
• May require removing the control panel or back cover to access mounting screws and wiring

This electronic clock/timer assembly displays the oven time and provides timer and timed-cook functions so you can monitor and control baking cycles. It replaces a failed or non-working oven clock to restore timekeeping and timer features. What it does:

• Displays current time and supports countdown/count-up timer functions
• Enables timed-start and timed-stop cooking features when used with the oven control
• Replaces a blank display, incorrect timekeeping, or a clock that won't respond to timer settings
• Works as the user-facing time/timer module for normal oven operation

• Disconnect power to the appliance at the breaker before starting any work.
• Handle the display and ribbon/connectors carefully to avoid damage to the module.
• Retain mounting screws and note any alignment tabs for proper seating during reassembly.
• After installation, restore power and set the clock/time per the owner's manual.

This clock timer replaces a failed oven clock and timer so the range or wall oven keeps time, uses timed bake/clean cycles, and provides clear display and control of timed functions. Restores clock display and basic timing features. What it does:

• Displays current time and lets you set timed bake, delayed start and self-clean cycles
• Controls oven timer countdowns and end-of-cycle alerts when functioning properly
• Replaces a clock that is blank, unresponsive, or showing incorrect time
• Works with the oven's timer functions to help manage cooking and cleaning cycles

• One clock timer

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle the control carefully; avoid touching circuitry or connectors directly
• Typical install requires removing the control panel; keep screws and parts organized