Frigidaire Range Parts

Replacement motor that restores mechanical drive or airflow in select Frigidaire appliances. Installs in place of the original motor to help return normal rotation, tumbling or fan operation. What it does:

• Drives rotating components (drum, tumbler, agitator or fan) depending on application.
• Helps restore normal spin, tumble or airflow when the original motor fails.
• Common symptoms: appliance won't start or spin, weak/uneven rotation, loud humming/grinding, or reduced airflow.
• Direct-fit replacement designed to match original mounting and electrical connections for specified models.

• Disconnect power (and water if applicable) before beginning any work.
• Avoid pulling on wires; reconnect all harnesses and secure mounting fasteners per OEM instructions.

This clock timer is the electronic oven control that governs timekeeping and oven functions. It displays the clock and settings and directs power to the bake/broil circuits so the oven responds to your commands.

• Controls and displays the clock, kitchen timer, and oven settings
• Sends power to bake and broil relays based on selected temperature and mode
• Coordinates preheat and cycle timing for consistent results
• Common signs it may be needed: blank or dim display, unresponsive buttons, error codes/beeping, oven won't start or heat though elements and power test good

• Disconnect power at the breaker before servicing—this is a high-voltage electronic part
• Access through the control panel or backguard; remove panel screws to reach the control
• Move wire connectors one at a time to the new control; reuse any mounting hardware
• Handle the board carefully to avoid static discharge; after installing, restore power and set the clock, then test oven functions

This electrical microswitch opens or closes a circuit when its actuator is engaged, allowing the control to sense position or enable a function. Replacing a worn switch restores reliable signaling and prevents intermittent faults in select ranges and wall ovens. What it does

• Changes state (open/closed) when actuated to complete or break a circuit
• Sends feedback to the control or enables power to a related component
• Helps ensure operations start/stop only when the mechanism is in the correct position
• Failure signs can include intermittent operation, cycles that won't start or finish, or related error codes/alarms

• 1 switch

• Disconnect power at the breaker before servicing
• Note/photograph wire positions and transfer one at a time to the new switch
• Match actuator orientation to the original and secure the switch firmly
• Verify function with a multimeter (continuity changes when actuated) before reassembly and testing

This surface element switch is the control behind your cooktop knob. It regulates power to the surface heating element so you can set and maintain the desired heat for reliable, consistent cooking performance.

• Regulates and cycles power to the surface heating element based on the knob setting
• Restores accurate low-to-high temperature control at the burner
• Typical failure symptoms: burner won't heat, only heats on high, or won't turn off
• Helps correct intermittent or uneven surface element heating

• Disconnect power at the circuit breaker before servicing
• Remove the knob and access the switch from the control panel or rear cover as applicable
• Photograph or label wire positions; transfer wires to the new switch one at a time
• Secure the switch, reassemble, restore power, and test all heat settings

Made by Frigidaire. This is a dual oven valve for bake and broil.

This safety valve controls gas flow to the oven burner, opening only when the ignition system calls for heat. Replacing a weak or stuck valve restores reliable ignition and consistent oven temperatures for safe, dependable baking and roasting. What it does:

• Regulates and shuts off gas to the oven burner circuit
• Works with the igniter; opens only when proper current is present
• Fails closed to help prevent unlit gas from entering the oven
• Common symptoms may include: oven won't heat, intermittent heating, very long preheat, or a weak/unstable flame

• 1 safety valve

• Disconnect power and shut off gas supply before servicing
• Label and transfer all tubing and wires from the original valve one-for-one
• Support flare fittings with two wrenches; use thread sealant only on NPT threads (never on flare connections)
• After installation, restore gas and check every joint for leaks with an approved leak-detection solution

The Ignitor is an OEM part for Frigidaire cooktops. It provides the spark necessary to ignite the gas on your range's surface burners. It generates a spark to ignite the gas flowing to the burner, ensuring a consistent and safe flame.

A bad ignitor can be caused by wear and tear, damage, or electrical issues. Signs of a faulty ignitor include the burner not lighting or a weak or inconsistent spark.

Symptoms of a bad ignitor include:

• Burner not lighting or requiring multiple attempts to ignite
• Weak or inconsistent spark 
• Visible damage to the ignitor, such as cracks or breaks

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Regulator is an OEM part for Frigidaire cooktops. It is responsible for regulating the flow and pressure of gas entering the appliance, ensuring safe and efficient operation.

A bad regulator can be caused by faulty internal components, wear and tear over time, or damage due to improper handling. Signs of a faulty regulator include uneven heating, weak flame, or gas leaks.

Symptoms of a bad regulator can include:

• Uneven heating of burners or oven 
• Weak or inconsistent flame 
• Gas leaks around the regulator 

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This genuine replacement cap restores a clean, finished look and helps protect the underlying fastener or opening on your appliance. Replace a missing or damaged cap to keep components covered and looking factory-fresh.

• Covers and protects an exposed screw, hinge, or opening from dust and debris
• Restores the appliance's finished appearance
• Helps maintain secure retention of the underlying component
• Common signs of failure: missing or broken cap, cap won't stay in place, cosmetic wear, visible exposed fastener/opening

• Disconnect power before servicing; if working near water or gas lines, shut those off as applicable
• Gently pry off the old cap; avoid scratching surrounding surfaces
• Align and press the new cap until it seats/snaps securely

Restore reliable timekeeping and timed-cycle control with this Clock/Timer Kit. It replaces a failed clock/timer so you can set the time, run countdowns, and receive alerts as designed by the manufacturer. What it does

• Displays and keeps the appliance's current time
• Controls kitchen timer/countdown functions and audible alerts
• Interfaces with the appliance to manage timed cycles (start/stop)
• Helps resolve issues like blank or dim display, timer not advancing, drifting time, or unresponsive keys/knob

• 1 clock/timer kit assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Access the control area; note screw locations and panel orientation
• Label or photograph wire locations; transfer connections one at a time to the new unit
• Mount securely, reassemble, restore power, and set the clock before testing timer functions

These chrome drip bowls sit beneath coil surface elements to catch spills and reflect heat. Sized for 8-inch and 6-inch burners, they refresh the cooktop's appearance and help elements seat correctly. What it does:

• Collects drips and splatters under coil elements and reflects heat back toward cookware
• Restores a clean look when originals are stained, pitted, or rusted
• Helps burners sit level and make solid contact with the cooktop
• Common signs to replace: heavy discoloration, rust, broken tabs, warping, lingering smoke or odor from burnt-on spills

• Two chrome drip bowls: one 8-inch and one 6-inch

• Disconnect power at the breaker and allow surface units to cool completely
• Pull the coil element straight out of its receptacle, then lift out the old bowl
• Align the new bowl's notches with the cooktop opening and seat it flat
• Reinsert the element fully and ensure it rests evenly in the bowl

This small cap snaps into the center of a control knob. It refreshes the appearance and helps keep moisture and debris out of the knob interior so the control stays protected and easy to use. What it does:

• Provides a finished cover for the center of a control knob
• Helps protect the knob interior from spills and debris
• Restores a clean look when the original cap is missing or damaged
• Addresses a loose or rattling knob insert

• 1 control knob cap

• Disconnect power to the appliance for safety before working near controls
• Pull the knob straight off the control shaft; remove any remnants of the old cap
• Align tabs and snap the new cap into the knob firmly
• Reinstall the knob on the shaft and verify smooth operation

This surface element installs beneath the glass cooktop and provides heat for a single cooking zone. Replacing a failed element restores responsive, even heating and dependable temperature control on your smoothtop range or cooktop.

• Generates radiant heat under the ceramic glass to cook food on the selected burner zone
• Common fixes: surface burner won't heat, heats unevenly, or works intermittently
• Replace if the element shows visible damage, hot spots, or burn marks beneath the glass
• Helps address long heat-up times on the affected zone

• Disconnect power at the breaker or unplug the appliance before servicing
• Lift/hinge the cooktop or remove the glass top to access the elements; support the glass to prevent damage
• Move wires from the old element to the new one one at a time to maintain correct connections
• Reuse existing mounting hardware/brackets; handle the ceramic element carefully to avoid cracks

The Glass is an OEM part for Frigidaire freestanding ranges. It provides a durable transparent barrier that allows for viewing of contents inside the oven. The tempered glass door is both impact-resistant and heat-resistant, built to withstand repetitive use.

Causes of bad oven door glass include cracks or chips developing from accidental impacts, warping or discoloration from overheating, or scratches that won't wipe clean. 

Symptoms of a bad glass oven door include:

• Inability to safely or securely close the oven door  
• Reduced visibility into the oven cavity
• Potential safety hazards from cracked or compromised glass

This OEM Frigidaire replacement restores the door's integrity and functionality. It is also compatible with Electrolux, Kelvinator, and some Kenmore electric range models. 

Restore a safe, finished oven door with this replacement outer glass panel. It replaces a cracked or shattered front window, protecting the door assembly and letting you see your food without exposing insulation or sharp edges. What it does:

• Forms the front/outer pane of the oven door window
• Protects door insulation and inner glass from damage
• Helps contain heat within the oven when intact
• Common symptoms: visible cracks, shattered or missing pane, loose or rattling glass

• 1 outer oven door glass panel

• Disconnect power and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; glass edges can be sharp
• Removing the door from the hinges makes service easier; support the door to prevent damage
• Transfer any trim/brackets/nameplate from the old pane and reuse existing hardware as required

This ignitor and orifice assembly provides the ignition source and gas orifice for a gas oven or range burner, restoring reliable ignition for cooking. Replaces a worn or damaged ignitor/orifice to help the burner light correctly. What it does:

• Supplies the ignition element and properly sized orifice so the burner can light and maintain a stable flame.
• Replaces burned-out or cracked ignitors that cause slow or no ignition.
• Replaces clogged or damaged orifices that can cause weak or uneven flames.
• Common symptoms it can address: burner won't light, repeated clicking with no ignition, or a weak/uneven flame.

• Turn off the appliance power and shut off the gas supply before servicing.
• Handle the ignitor carefully—the ceramic/sensing tip is brittle and can break if dropped or bumped.
• Disconnect electrical connectors and note wire positions before removal; reconnect exactly as found.