Frigidaire Range Parts

This potentiometer kit is the user-adjustment control the appliance reads to set operating levels. Replacing a worn potentiometer restores smooth, predictable response when you turn the knob, helping the control register settings accurately.

• Varies electrical resistance so the control can interpret knob position
• Helps set functions such as speed, power level, or temperature as designed
• Failure can present as no change when turning the knob, jumpy/erratic response, or settings stuck at one level
• Can also cause intermittent operation or "dead spots" while adjusting

• Disconnect power to the appliance before servicing
• Access the control area; note wire positions or take a photo before removal
• Transfer any knob/shaft adapter from the old part if applicable; secure the new pot without over-tightening
• Route wiring away from sharp edges and heat sources; verify proper operation before reassembly

This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:

• Transfers power and control signals between components so controls and motors can operate
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps stop failures that lead to no-start or loss of specific functions
• Restores secure connector fit to reduce arcing or poor connections

• Always disconnect power before servicing the appliance
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Secure fasteners and strain reliefs; verify all connections are fully seated
• If you find heat or burn damage at terminals, inspect adjacent components for root cause

Replace a broken, cracked, or missing control knob on your electric cooktop. Installs on the control panel to adjust burner settings and temperature.

The Surface Burner Base is an OEM part for Frigidaire gas ranges. It provides a stable foundation and housing for the range's burners. Each burner base has a molded indentation to securely hold the burner assembly in place while cooking. 

Causes of a bad Surface Burner Base can include warping or distortion from overheating, cracks or punctures from impact or mishandling, or damage from corrosion over time.

Symptoms of a bad Surface Burner Base include: 

• Burners wobbling or moving out of position during use
• Gas or liquid leaks around burner housing 
• Irregular or uneven cooking performance 
• Loose, damaged, or missing burner assemblies

This genuine OEM Frigidaire base is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

Secures the glass light cover to your range oven cavity. Replace if the retainer is cracked, broken, or missing to keep the lens firmly in place.

Color: white. Measures about 2 inches in diameter.

This is a black surface burner cap that sits on top of the burner base on a gas range cooktop. It distributes the gas flame evenly around the burner for consistent heating. Replace this cap if it is chipped, cracked, warped, or if you notice uneven flame patterns or difficulty igniting the burner.

Replaces cracked or corroded sealed burner head on gas ranges and cooktops. Restores proper flame distribution when original part is damaged or clogged.

Combines spark igniter electrode with orifice holder for gas surface burners. Replace when cracked, broken, or no longer securely holding components in place.

Replacement handle for range oven doors. Installs on the front door panel for gripping and opening. Needed when original handle is cracked or broken.

This genuine OEM part is a clock timer for ovens. The clock timer is the part of the oven that allows the user to set a time for cooking and baking. If the timer buttons are no longer responding to touch or the timer's digital display is no longer visible, it will need to be replaced. Luckily, replacing a timer is a fairly simple repair.To get started, make sure the range is unplugged. Once unplugged, pull the range out and away from the wall to gain access to the upper back panel. Remove the mounting screws to the panel to gain access to the back of the control panel. Locate the timer and proceed to unthread the screws that hold it in place. Once loosened, pull the timer out of its place and install the new timer by threading the mounting screws that secure it to the control panel. Reinstall the upper back panel and restore power to the appliance.This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

Fixes blank or flickering clock display and non-functioning countdown timer on your range. Restores oven timing accuracy. Moderate DIY difficulty.

Low-friction slide piece that supports moving components in your range or wall oven. Replace worn or cracked glides to restore smooth operation.

Fix a burner that won't heat on your glass cooktop. This radiant surface element restores even heating and temperature control. DIY-friendly repair.

This is a gas valve that controls the flow of gas to a surface burner on a gas range. It connects to the burner control knob and regulates the flame from high to low settings. Replace this valve if a burner won't ignite, the flame is uneven or won't adjust properly, or you detect a gas smell when the knob is in the off position. Includes mounting screw.

Snap-on burner cap for gas cooktops and ranges. Restores finished appearance and protects components. Replace if cracked, chipped, or missing.