Frigidaire Range Valve

The Oven Safety Valve is an OEM replacement part for Frigidaire gas ranges. This valve controls gas flow to the oven burner.

Causes of a faulty oven safety valve can include wear of sealing surfaces due to prolonged heating and cooling during cooking cycles. Exposure to food or liquid residues over time may also affect valve function.

Symptoms of a bad oven safety valve include:

• The oven not heating up despite the igniter working correctly
• A smell of gas indicates a leak or uncontrolled release
• Inconsistent oven temperatures or heating patterns
• The oven failed to maintain the set temperature

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This valve controls gas flow to a range/cooktop surface burner for smooth ignition and precise flame adjustment. Replacing a worn valve helps restore reliable burner lighting, accurate heat control, and safer shutoff.

• Regulates gas to a surface burner for ignition and flame size control
• Sticking or worn internal seals can cause hard-to-turn operation or gas odor
• Failure may prevent the burner from lighting or shutting off completely
• Inconsistent or unresponsive flame adjustment can indicate a failing valve

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; access the valve/manifold per your model's instructions
• Mark and disconnect tubing and any wires; transfer fittings or a separate spark switch from the old valve if applicable
• After installation, restore gas and check all joints with an approved leak-detection solution; verify proper burner operation

Made by Frigidaire. This is a dual oven valve for bake and broil.

This surface burner gas valve regulates the flow of gas to the burner on your range or cooktop, enabling proper ignition and flame control. Replacing a worn valve restores safe operation and consistent flame performance.

• Meters gas to the burner in response to the control knob
• Supports reliable ignition and maintains a stable, adjustable flame
• Typical symptoms: burner won't light, flame won't adjust or goes out, knob stiff or difficult to turn
• Can help correct uneven heat on the affected burner

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; remove panels as directed by your model's service information
• Note valve orientation; transfer any model-specific brackets or fittings from the old valve if required
• After reassembly, check all connections for leaks with a soap-and-water solution

This replacement part is a safety valve. This part is found in various types of refrigerators or freezers and is able to ensure that the appliance is running smoothly and safely during use. A new safety valve might be needed if the user notices that the current one is no longer working properly. This may include it having a leak or making unfamiliar sounds. The user should be able to access the back of the appliance to replace or repair this part.This is a genuine OEM replacement part made by Frigidaire, sold individually. The item, made of durable materials, is meant to last a long time.

This safety valve controls and shuts off gas flow to the appliance burner assembly to help prevent unintended gas delivery. It restores safe operation when a failed valve is replaced and the ignition system is working properly. What it does:

• Regulates and stops gas flow to the burner/oven when the valve is closed
• Prevents gas from reaching the burner when ignition is off or unsafe conditions occur
• Common symptom fixes: no heat, continuous clicking with no ignition, or a persistent gas smell when appliance is trying to light
• Works with the appliance's ignition and pressure systems to maintain safe fuel delivery

• Turn off gas and power at the appliance before starting work
• Use appropriate tools and follow the appliance service manual; fittings may require thread sealant rated for gas
• After installation, check all connections for leaks with a non-corrosive leak detector or soapy water; do not use an open flame

This safety valve controls and shuts off the flow of gas to the appliance, helping the cooktop or oven heat safely and reliably. It replaces a failed valve to restore proper gas control and safe operation. What it does:

• Regulates gas flow to the appliance's burner assembly and/or pilot circuit
• Stops gas flow if the valve or control circuit fails, preventing unsafe leaks
• Common symptom: appliance won't heat or burners won't light despite power to the igniter
• Common symptom: intermittent heating or unit shuts off unexpectedly during operation

• One safety valve

• Turn off gas supply and disconnect power before servicing
• After installation, check all gas connections for leaks and verify proper ignition and shutoff operation
• Do not attempt repair if you smell gas; evacuate area.

This water inlet valve controls the flow of water to the refrigerator's dispenser and icemaker, ensuring reliable water delivery for drinking and ice production. Replace a failing valve to restore normal water flow and prevent leaks. What it does:

• Opens and closes to supply water to the dispenser and icemaker when needed
• Stops water flow to help prevent continuous filling or flooding
• Commonly used when dispenser water is weak, icemaker won't fill, or there is leaking near the valve
• Matches OEM function and fit for compatible Frigidaire refrigerators

• One water inlet valve

• Shut off water and power to the appliance before starting any repair
• Handle water lines and electrical connectors carefully; replace worn gaskets or seals as needed

This thermal cutoff is a temperature-sensing safety thermostat that helps prevent overheating by interrupting power when excessive heat is detected. Use it to restore proper safety protection in affected appliance heater or control circuits. What it does:

• Monitors temperature and opens the circuit if heat rises above the designed threshold
• Helps prevent overheating-related damage or fire risk in heating systems
• Stops power to heating elements when a fault causes unsafe temperatures
• Commonly used with ovens, dryers, and other heater-equipped appliances as a fail-safe

• One thermal cutoff

• Power must be disconnected before inspection or replacement to avoid shock or injury
• Handle the part carefully and observe wire connection orientation; replace with same type only
• If other components show heat damage, inspect the whole heating circuit and controls

A replacement safety valve kit that restores a safety shutoff component to appliances, helping stop flow when a fault is detected so the unit can operate safely. Fits compatible Frigidaire appliances that use this OEM kit. What it does

• Replaces the appliance's safety valve assembly to restore proper shutoff function
• Prevents continued fuel or water flow when a fault or unsafe condition occurs
• Commonly used when the appliance fails to start, fails to heat, or shows safety-related shutdowns
• Helps resolve intermittent operation or safety trip symptoms tied to a failed valve

• One safety valve kit (single complete replacement kit)

• Disconnect power and gas/water supply before starting any repair
• Follow the appliance's service manual or wiring diagram for correct routing and connections
• Use proper tools and safety gear;
• Test for leaks and proper operation after installation and before returning the appliance to service

This water inlet valve controls water flow to the refrigerator's dispenser and ice-making system, restoring proper water delivery when the factory valve fails. Designed as a direct-replacement valve assembly for compatible Frigidaire units. What it does

• Opens and closes to allow water into the ice maker and door dispenser when signaled
• Prevents water flow when the dispenser or ice maker is inactive
• Common symptom: dispenser or ice maker does not dispense water or fills slowly
• Common symptom: water intermittently flows or the ice maker fails to fill

• Disconnect power and shut off the water supply before beginning work
• Drain remaining water from lines to limit spills during removal
• Replace mounting hardware and tubing fittings exactly as removed; use plumber's tape where appropriate on threaded connections
• Inspect connections and test for leaks after restoring power and water