Frigidaire Refrigerator Screws, Nuts, Washers

Replacement screw used to secure trim, brackets and panels on compatible Frigidaire appliances. Restores proper fit to reduce rattling and keep components from coming loose for safer, more reliable operation. What it does

• Secures panels, trim pieces and small brackets so parts stay aligned and flush.
• Stops rattling or vibration caused by missing or loose fasteners.
• Prevents components from shifting or falling out during normal use.
• Works wherever the OEM screw specified by the appliance diagram is required.

• Disconnect power (and water, if applicable) before starting any repair.
• Use the correct driver and size to avoid stripping the head or threads.
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic.
• If the new screw does not seat properly, confirm this is the correct OEM part before forcing it.

This is a replacement screw fastener used to secure panels, trim, or components on compatible Frigidaire appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or trim pieces to keep components aligned and stable
• Prevents rattling, vibration noise, and gaps caused by missing or loose fasteners
• Restores proper assembly after service or part replacement
• Helps maintain safety by keeping covers and guards firmly attached

• One screw (single fastener)

• Disconnect power or unplug the appliance before servicing
• Use the appropriate driver to avoid stripping the head; do not overtighten
• Verify the screw matches the original in length and thread before installing

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

This genuine appliance screw secures panels and components to keep your refrigerator parts aligned and stable. A small but essential fastener, it restores proper fit and stops rattling or loose trim for reliable operation. What it does:

• Fastens panels, trim, or internal components to the appliance frame
• Restores secure fit when factory screws are missing or stripped
• Stops vibration- or temperature-related rattling caused by loose hardware
• Helps maintain proper spacing and alignment of serviceable parts

• Turn off and unplug the appliance before servicing electrical or internal areas
• Use the matching screw hole and thread engagement; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking surrounding material

#10 pan head 8 - 18 x .5

A replacement hex nut that secures threaded fasteners on Frigidaire appliances. This small but essential hardware restores proper attachment of panels, brackets, and components so parts stay tight and appliances run quietly. What it does:

• Secures components by threading onto matching bolts or studs to hold panels, trim, brackets, or assemblies in place
• Stops loose or rattling panels caused by a missing or worn nut
• Maintains proper alignment of attached parts to prevent vibration-related wear
• Simple, low-profile fastener used across multiple internal and external appliance locations

• Disconnect power to the appliance before starting any repair
• Use the correct-size wrench or socket and tighten snugly; avoid overtightening to prevent stripping threads
• If the original stud or bolt is damaged, replace that component as well for a reliable repair

This replacement mounting screw secures components and panels in refrigerators and freezers, restoring proper fit and stopping loose or rattling parts. Use when original screws are missing, stripped, or damaged. What it does:

• Fastens trim, panels, brackets or small components to the appliance frame
• Restores secure attachment to stop rattling or intermittent contact
• Replaces stripped, corroded, or missing screws to prevent parts from shifting
• Simple, direct replacement that matches the original mounting point

• Use the matching driver bit to avoid stripping the screw head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power to affected appliance areas before servicing if panels expose wiring
• If threads are damaged, replace the mating nut or tapped insert as needed

This genuine replacement screw secures appliance components and restores proper fit and stability. Use it to replace a missing or damaged fastener and stop panels, trim, or parts from shifting or rattling during normal use. What it does:

• Fastens and holds panels, brackets, or small components in place
• Restores secure attachment when an original screw is missing, damaged, or stripped
• Helps eliminate vibration, rattling, or loose-fitting parts
• Matches the OEM fit and function for reliable reassembly

• Use correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and remove food or contents from appliance areas as needed before servicing
• If fastener threads are damaged, replace with the exact OEM screw rather than forcing installation

This nut-anchor is a small mounting insert that provides a secure threaded point in thin sheet metal so screws can fasten panels or components reliably. It restores a solid attachment where the original fastener or threaded hole is missing. What it does:

• Provides a reinforced threaded anchor in thin metal or plastic panels
• Allows screws to tighten without stripping the sheet material
• Stops panels, trim, or assemblies from coming loose or rattling
• Used where a captive nut or threaded insert is required for reassembly

• Install where original nut/insert was located; verify orientation before fastening
• Use the correct screw size and hand-tighten to avoid overtightening or thread damage
• Disconnect power and move the appliance to a safe, stable work area before servicing
• If the original mounting point is severely damaged, consider assessing the surrounding structure for repair

This is a replacement screw used to secure appliance panels and components. It restores proper fastening to stop rattles and keep parts aligned for reliable operation. What it does:

• Secures trim, brackets, or small panels to the appliance
• Prevents loose parts that can cause vibration, noise, or improper sealing
• Restores factory fastening where a screw is missing or damaged
• Simple, single-purpose fastener — use where the original screw was installed

• Use the matching screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage
• Disconnect power or follow appliance safety steps when working near electrical components
• Replace only the screw(s) that match the original size and type