Frigidaire Wall Oven Parts

The problem seemed to be with the switch so I watched a few youtube videos to learn more about how ranges work. After locating the correct replacement switch I ordered it on-line around 10 pm Tuesday night. The new switch arrived Thursday morning at about 10 am and I had my range back up and working like new in less that 30 minutes. The hardest part was figuring out how to remove the slide in panel to access the switch. There were plastic washer/nuts behind each know which I was able to... Read more

Purchased a new over control board and overlay. Installed in five minutes, and everything works great now. Shipping was super fast, and was here within two days. Read more

After checking all connections to ensure power was getting to element. I ordered new control board and replaced it myself. Saved about $100.00 on a service call for someone to come out and replace it Read more

Replaced the regulator with part #AP5802175. Watched the video when purchasing, and it was spot on. Would have taken me about 15-20 minutes if I had access to a vise, to remove one of the fittings. Was able to get it out using two wrenches, but it was not without a bit of elbow grease. The new part went in easily. Turned on valve on regulator, plugged in the power, turned on the gas valve, done. Everything worked fine. Easy job for anyone with just a few tools. Read more

I googled the error code and symptoms my oven was exhibiting to determine the solution and which parts to order. I needed a new control panel and chose also to replace the overlay that shows on the front of the stove. I could have reused the old one because I turned out to be able to remove it without damaging it. I just kept it in case I damage the new one in the future. The “fast” shipping (not overnight) option had the part delivered the next morning, which was a nice surprise. I felt... Read more

Replaced the oven heating element Read more

Replaced the infinite, dual, switch. Very good instructional video for Safety, removal * install. Read more

Ordered replacement parts Read more

Repair man said that the part alone would cost more than $300.00. I checked it out on YouTube and saw that the actual replacement was an easy task. I contacted appliancepartspros.com and spoke to Wendy, who sorted me out with the correct part which arrived in two days ($115.00). It took me less than 15 minutes to replace the part, no more leak. Thanks appliancepartspros.com and Wendy for your cost effective and speedy service. Read more

The glue behind the keypad loosened and the keypad slowly began slipping down out of place over several months. Finally, because of the movement, it warped which resulted in one of the keys being stuck. That is what gave the F12 error code. The fix was easy. I removed the control panel and then peeled off the keypad. The keypad itself then has two layers (1), the flexible circuit panel, and (2) the outward facing display. I separated the display from the circuit panel and put the new one... Read more

• Door won't close

My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more

Replaced the element. 1st- Turn off the power to the appliance. The cook top is held on with two screws - access the screws by opening the oven door. Cooktop is hinged, so just pull up near oven door and hold in place with, say, a three foot long stick. The elements are held in place by bracket attached to the cooktop. Remove the bracket by removing the two socket screws. The element is aligned to the bracket with three locking tabs. Remove the tabs with pliers. I broke off one the... Read more

Turns out these wall ovens have a pretty common problem, the baking element relay on the back of the control board solder joint fails. We have had this happen on several units recently as we manage several apt complexes. So it was not the baking element at all, just faulty solder joints or something makes the baking element relay lose its solder connection. Read more

Removing was easy. Pull out the ends of the seal, the ends aren't locked in. Then, pull up on each retaining clip. Each clip is held in with spring tension. Reinstallation was easy too. Start on one end, Twist frayed end into cone-like shape and insert into one of the holes for the seal. Push in with a skewer/screwdriver. Insert first clip into the first hole. Go around in a linear fashion, inserting each clip into each hole. After the last clip is pushed in, twist the end of the frayed end... Read more

Removed the bottom tin work in the oven and removed the burner tube. Tried to remove the igniter bracket but the screws were too tight for the Phillips head and couldn't get vice grips to clamp on the head, so I bent the bracket enough to remove and replace the igniter. Then reassembled. I give AppliancePros.com a 5 star rating. Site was easy to use, the part was delivered in under 2 days, and it was the correct part packaged carefully so the igniter was protected from breaking. Read more

I had to order the glass, frame, and cap that the handle attaches to. I just had to put in about 6 screws, it was very simple. Read more