Frigidaire Washer Parts

Pressure tube connects washer tub to water level switch. Replace if cracked, kinked, or clogged to restore proper water level sensing in your laundry center.

Adjustable leveling leg threads into washer base to stabilize and level the cabinet. Replace worn, missing, or broken legs to prevent rocking and vibration.

Flexible hose for washers that connects water or drain lines between components. Replace if your hose is cracked, collapsed, clogged, or leaking.

Fix a washer that won't advance cycles or start filling water with a new timer. Controls cycle timing and electrical components. 10-15 minute DIY repair.

This control knob replaces a worn, cracked, or missing range/stove dial so you can select heat and settings with a secure grip and clear position indicator. It restores normal operation of the control shaft. What it does:

• Fits onto the control shaft to turn the burner/oven setting and indicate the selected position.
• Restores a solid grip and visible pointer for precise adjustments.
• Common symptom fix: knob is loose, stripped, cracked, or missing and won't turn or hold a setting.
• Helps avoid accidental setting changes from a damaged or worn knob.

• Disconnect power to the appliance before service to avoid shocks or accidental heating.
• Pull the old knob straight off the control shaft; line up splines and push the new knob onto the shaft until fully seated.
• Do not force or hammer the knob onto the shaft; if it does not seat easily, verify spline alignment.
• If the control stem or switch is damaged, replace the stem/switch assembly rather than forcing a knob.

Replacement washer door hinge that secures and aligns the door for smooth opening and closing. Needed when original hinge is cracked, broken, or worn.

This is the complete detergent dispenser drawer assembly for a front-load or top-load washing machine. It holds and dispenses detergent, fabric softener, and bleach at the appropriate times during the wash cycle. Replace this assembly if the dispenser drawer is cracked, if detergent is not dispensing properly, or if residue builds up and cannot be cleaned out.

This is a metal hinge that attaches the dryer door to the cabinet and allows it to swing open and closed. It supports the weight of the door and ensures proper alignment with the door latch. Replace this hinge if the dryer door is sagging, not closing properly, or if the hinge is cracked, bent, or has worn-out pin holes.

This is the main electronic control board that manages all washer functions, including cycle selection, water fill, motor operation, and spin speed. It is typically mounted inside the control panel or rear of the machine and connects to the various components via wire harnesses. Replace this board if the washer fails to start, stops mid-cycle, displays error codes, or if buttons and cycle selections are unresponsive.

This is a small metal or plastic retainer clip that secures the main top panel of the dryer to the cabinet frame. It holds the top panel firmly in place so it doesn't shift or rattle during operation. If your dryer's top panel feels loose, pops up during use, or won't stay properly seated, this clip may be broken or missing.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This hardware kit includes the mounting brackets and fasteners needed to secure a laundry pedestal to a washing machine or dryer. The pedestal raises the appliance to a more comfortable loading height and may include a storage drawer. Use this kit when installing a new pedestal or replacing missing or damaged mounting hardware.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Mounting bracket secures components inside your laundry center. Replace if bent, broken, or missing to eliminate rattling and restore stability.

Washer air chamber connects the water level pressure switch to the tub. Replace if cracked, kinked, or disconnected causing water level issues.

This mechanical timer controls the sequence and duration of wash, rinse, and spin cycles in a front load washing machine. It sends electrical signals to the various components - such as the motor, water valve, and drain pump - at the correct times during the cycle. Replace the timer if the washer gets stuck on one cycle, skips cycles, or fails to advance through the wash program.