General Electric Dishwasher Parts

Fix dishwasher buttons that won't respond or cycles that won't start with this push button switch. Direct replacement for worn control panel buttons.

This is a replacement washer drive motor that powers the tub to spin and agitate, restoring normal wash and spin cycles. Fits specified GE top-load washers and matches OEM form and function. What it does

• Spins the wash tub to perform spin cycles and remove water
• Powers the agitation/oscillation action during wash cycles
• Commonly replaced when the washer won't spin, won't agitate, or hums without turning
• Helps eliminate intermittent power-to-motor issues when motor failure is the root cause

• One replacement drive motor

• Disconnect power before starting any repair to avoid electric shock
• May require removing the washer cabinet or access panels and detaching the old motor wiring and mounting screws
• Handle carefully — support the tub/drum as needed during motor removal and reinstallation

Secures hose connections to prevent leaks in your dishwasher. Replace if water pools under the unit or connections feel loose. Confirm fit with your model.

A stainless steel hex-washer-head screw used to secure panels and components on compatible appliances. Corrosion-resistant construction helps maintain a secure fit where short, strong fasteners are required. What it does

• Fastens appliance panels, trim, or brackets where an 8-18 thread and short 3/8" length are specified
• Hex washer head provides a larger bearing surface to reduce pull-through
• Stainless finish resists rust in humid appliance areas
• Common replacement when original mounting screw is stripped, missing, or corroded

• One stainless steel hex-washer-head screw

• Use the correct 8-18 thread fastener and do not force mismatched screws to avoid thread damage
• Tighten securely but avoid overtightening to prevent stripped threads or cracked panels
• Power tools may be used with appropriate bit, but start by hand to ensure proper alignment
• If installing near electrical components, disconnect power before servicing

Thread-forming screw secures dishwasher panels, brackets, and trim components. Replace missing or stripped fasteners to restore proper mounting.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

Lower rack roller and stud assembly for dishwashers. Mounts to the bottom rack to allow smooth sliding in and out. Replace if broken, cracked, or missing.

This mechanism assembly is the timed control component that advances and governs cycle functions, restoring proper cycle sequencing and timing for the appliance. It replaces a worn or non-advancing timer mechanism. What it does:

• Advances the appliance timer so cycles progress to the next step
• Controls mechanical switch cams that engage heating, agitation, or spin
• Commonly helps when cycles won't advance, stop mid-cycle, or run continuously
• Works as the core drive for mechanical timer-based controls

• Disconnect power before servicing to avoid shock or injury
• Handle gently; align cams and shafts as OEM instructions specify
• Refer to the appliance's service manual or tech sheet for exact alignment and testing procedures

Fix dishwasher not draining or cleaning issues with this pump and motor assembly. Resolves loud grinding noises and poor water circulation problems.

Secures wine glasses and goblets in your dishwasher rack. Replace broken, cracked, or missing stemware clips to prevent tipping during wash cycles.

Top cover for your dishwasher's silverware basket. Replaces a cracked, broken, or missing lid to restore secure closure and keep utensils contained.

User-facing button assembly for the dishwasher control panel. Replace when buttons are unresponsive, cracked, worn, or indicators are dim or missing.

This push button is the user-facing control button that completes a control circuit when pressed, restoring responsiveness to a worn or broken selector interface. It provides a direct, replaceable way to fix unresponsive or stuck control input. What it does

• Acts as the external control button that engages the appliance's internal switch when pressed
• Restores tactile feedback and reliable control input if the original button is cracked, loose, or missing
• Common symptom fix: buttons that stick, don't depress fully, or fail to activate functions
• Works with the matched internal switch assembly to ensure consistent operation

• Disconnect power before any service
• Remove the control panel or bezel as needed to access the button; avoid prying on surrounding trim
• Replace the button by aligning and snapping it into the button housing; do not force or bend retaining tabs
• If the button does not restore function, inspect the underlying switch/mechanism for damage before ordering additional parts

Secures dishwasher drain or inlet hoses to fittings to prevent leaks and slipping. Replace when loose, corroded, or during hose installation. Verify fit.

Guide casing that supports and aligns the dishwasher spray arm assembly. Replace if cracked, broken, or worn to restore proper fit and alignment.

Left-hand door hinge assembly for dishwashers. Installs on the left side to support and secure the door to the cabinet. Replace if bent, broken, or worn.