General Electric Range / Cooktop / Oven Wire, Harness, Power Cord

Replacement burner wire harness that restores the ignition wiring connection for a gas range surface burner, helping re-establish consistent sparking and reliable burner ignition for safe cooking operation. What it does:

• Provides the electrical connections between the burner igniter/spark electrode and the range's ignition module/control.
• Replaces damaged, cut, or frayed wiring that can cause no-spark, intermittent ignition, or continuous clicking at the burner.
• Routes and secures ignition wires to keep connections stable and reduce heat/rub-related failures.
• Helps the ignition system deliver consistent sparks so burners light reliably.

• Disconnect electrical power and shut off the gas supply before beginning any service.
• Compare the new harness to the original; transfer and reconnect terminals one-to-one and secure any routing clips or fasteners.
• Route wires away from hot surfaces and sharp edges; avoid stretching or pinching the harness.

This harness connects the burner box wiring to the cooktop's controls and safety devices, ensuring reliable ignition and proper sensor/valve communication. Replaces a damaged or worn burner-box harness to restore safe burner operation. What it does:

• Carries power and signals between igniters, flame sensors/thermocouples, and gas valves
• Supports ignition; failure can cause burners to not light or spark inconsistently
• Prevents intermittent operation caused by frayed wires, loose connectors, or heat damage
• Helps maintain correct sensor feedback for safe gas shutoff

• One burner box wiring harness

• Disconnect power and shut off gas supply before starting any repair
• Match connector styles and routing to the original harness; inspect nearby components for heat damage
• Use proper strain relief and secure fasteners to prevent contact with hot surfaces

This harness burner box is the electrical ignition harness assembly that routes power and signals to the range/stove burner valves and igniters, restoring reliable spark and control at the burner module. What it does

• Routes ignition and valve control wiring between the cooktop control module and individual burner valves/igniters.
• Enables spark ignition and proper valve response so burners light when controls call for flame.
• Commonly replaces worn or damaged harnesses that cause intermittent ignition, no-spark, or unresponsive valves.
• Keeps wiring organized and secured inside the burner box to prevent chafing or shorts.

• One harness burner box assembly as shown.

• Disconnect electrical power and shut off gas supply before starting work.
• Handle connectors carefully; match wire connectors and routing to the original harness during replacement.
• Inspect surrounding terminals and components for heat or corrosion damage and replace if needed.

This harness burner box is the wired ignition assembly that routes spark and power to a cooktop's burner valves and igniters, restoring reliable ignition and consistent burner operation. What it does

• Delivers spark and electrical connection to surface burner igniters and gas valve controls.
• Replaces damaged or frayed wiring that can prevent burners from sparking or lighting.
• Restores proper routing and secure connections to reduce intermittent ignition failures.
• Intended for use with compatible gas range cooktops that use a burner-box ignition harness.

• Designed for experienced DIYers; disconnect power and shut off gas before starting.
• Inspect mating connectors, igniters and valves while installing; replace any visibly damaged components.

This replacement line cord provides the appliance's main power connection, restoring a safe, reliable electrical feed when the original cord is damaged or worn. Use it to replace frayed, cut, or non-functioning power leads. What it does:

• Carries household mains power to the appliance for normal operation
• Replaces damaged or frayed cords that can cause intermittent power or visible wear
• Helps eliminate loose connections, burning smell, or sparking at the cord entry
• Restores a secure grounded connection when used with the correct grounding configuration

• Disconnect power at the breaker or unplug the appliance before starting
• Verify cord type and grounding configuration match the appliance wiring and local code
• Inspect terminal connections for corrosion and tighten to manufacturer torque specs

Note: Ignitor wires

This burner wire harness assembly routes power and signals between the control and the burner components so your range or oven can ignite and operate correctly. It replaces a damaged or corroded wiring harness to restore reliable ignition. What it does:

• Carries electrical connections from the control/igniter to the burner for proper ignition and heating
• Replaces broken, melted, or corroded wires that can cause intermittent or failed ignition
• Helps stop sparking issues or burners that don't light when the control calls for heat
• Restores secure connector fit and proper wire routing to prevent shorts or arcing

• One burner wire harness assembly

• Disconnect power (and gas supply for gas ranges) before starting any repair
• Handle connectors gently and match connector shapes; ensure all plugs seat fully
• Route and secure the harness away from high-heat surfaces and moving parts

This harness module routes power and control signals between the appliance control system and internal components to restore reliable electrical connections and proper function. What it does:

• Connects control board circuits to motors, switches, sensors, or valves for coordinated operation
• Re-establishes intermittent or lost electrical paths that can cause components to stop responding
• Helps resolve symptoms like parts that won't run, intermittent operation, or related error codes
• Ensures connectorized wiring is organized for correct signal routing and secure contact

• Disconnect power to the appliance before accessing electrical components to avoid shock
• Handle connectors gently; match keyed plugs and fully seat each connector during installation
• Route harness away from heat sources and moving parts; secure with existing clips or ties
• If wiring, insulation, or connectors are damaged, replace the entire harness rather than splicing

This ribbon connector (GLS) is a flat multi-conductor connector used on select appliances to link glass/control assemblies to the main wiring harness, restoring electrical continuity for control functions. Ideal when a broken or corroded connector causes intermittent or no control response. What it does:

• Provides a secure flat cable connection between control/glass assemblies and the main wiring harness
• Restores signals for touch controls, lights, or display functions when a damaged connector is the cause
• Prevents intermittent electrical contact from bent, burned, or corroded terminals
• Compatible with replacement of worn or physically damaged ribbon connectors

• Turn off power to the appliance at the breaker or unplug before starting work
• Handle the flat ribbon and terminals carefully to avoid bending or damaging contacts
• Confirm connector orientation and seating; do not force the connector into place