General Electric Wall Oven Parts

This relay board assembly switches line power to the range/oven's heating circuits under the direction of the electronic control, helping restore reliable bake/broil operation when relays or board components fail. What it does

• Controls power to the bake and broil elements via onboard relays
• Executes low-voltage commands from the control to switch high voltage to the heating circuits
• Failure symptoms can include no heat in bake or broil, one element not working, or intermittent heating
• Burn marks or a stuck/clicking relay on the board may be visible indicators of failure

• 1 relay board assembly

• Disconnect power at the breaker before servicing; this board carries live voltage
• Access location varies by model; photograph and label all wires for correct reassembly
• Handle the board by its edges and observe ESD precautions
• Ensure all connectors are fully seated and the board is securely mounted before restoring power

This convection element mounts at the rear of the oven and supplies heat during convection cycles. Replacing a failed element restores consistent, circulating heat for reliable baking and roasting performance. What it does:

• Provides the primary heat source for convection mode at the back of the oven
• Works with the convection fan to circulate hot air for even results
• Helps maintain steady oven temperature during preheat and cycling
• Common symptoms: no heat in convection mode, slow preheat, uneven baking/roasting, or visible damage to the element

• 1 convection heating element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks and the rear interior cover/baffle to access the element
• Note wire locations, transfer existing mounting hardware, and reconnect wires to the same terminals
• Avoid flexing the element; ensure tight connections before restoring power and testing

This electronic oven control board manages bake/broil power, temperature regulation, and the clock/display for the range. Replacing a failed control restores accurate heating, reliable cycle timing, and responsive keypad/display operation.

• Regulates bake and broil element power using feedback from the oven temperature sensor
• Controls oven temperature, cooking cycles, and timing functions
• Operates the clock, display, and keypad interface
• Typical failure symptoms can include no heat or won't start, won't reach/hold set temperature, blank/unresponsive display, or error codes/beeping

• Disconnect power at the breaker before servicing
• Handle the new board by the edges and use anti-static precautions
• Photograph wiring and move connectors one at a time; transfer any mounting brackets and the user interface overlay from the original
• After installation, set the clock and test bake/broil operation

This electronic oven control board manages the oven's heating functions, temperature regulation, and display/clock. Replacing a failed board restores accurate temperature control and responsive controls so your oven can heat and keep time reliably.

• Controls power to bake and broil elements based on user input and sensor feedback
• Regulates oven temperature and cycle timing
• Drives the display and processes keypad/selector inputs
• Common failure symptoms: no heat, won't start, blank/unresponsive display, beeping/error codes, inaccurate oven temperature

• Disconnect power at the breaker before servicing
• Handle the board with ESD care; avoid touching component contacts
• Note/photograph wire positions; transfer connectors one at a time and reuse existing brackets as needed
• After reassembly, restore power, set the clock, and test bake/broil per the service sheet

This is the outer glass panel for the oven door. Replacing a cracked or shattered exterior pane restores a safe, clean-looking door surface and helps protect the inner window and insulation from damage. What it does:

• Forms the front layer of the oven door and shields the inner window/insulation
• Provides a smooth, easy-to-clean exterior surface and finished appearance
• Helps maintain proper door integrity when the original glass is broken or missing
• Common symptoms include cracked or shattered glass, loose/rattling trim, or sharp edges on the door exterior

• 1 outer oven door glass panel

• Disconnect power; for gas ranges, also shut off the gas supply
• Allow the appliance to cool completely before service
• Wear cut-resistant gloves and eye protection; handle tempered glass carefully
• Support or remove the door; transfer handle/trim and reuse original hardware; do not overtighten fasteners

This hold-down bracket secures a designated component inside your appliance, keeping it firmly anchored during use. Replace a bent, broken, or missing bracket to stop movement and rattling and restore proper alignment and a stable, factory fit. What it does:

• Anchors the specified part to the appliance frame/cabinet to prevent shifting
• Reduces vibration and rattling noises during operation
• Helps maintain correct alignment and spacing for reliable performance
• Replace if the bracket is bent, cracked, corroded, or missing

• 1 hold-down bracket

• Disconnect electrical power; for gas appliances, also shut off the gas supply
• Note the original orientation and screw locations before removal (a quick photo helps)
• Reuse existing mounting hardware unless your model specifies new fasteners
• Do not overtighten; verify the secured component is aligned and stable before restoring power

This is the door pad. Consider replacing both when replacing trim number WB07T10230

Size: 10-32 GXTT FLP.595 S

This ring-style convection heating element mounts around the fan at the back of the oven and supplies heat for convection cooking. Replacing a failed element helps bring back even air heating and consistent convection bake performance.

• Provides the heat source for convection bake/roast by warming air circulated by the fan
• Helps maintain set temperature and more even results in convection mode
• Common failure signs: no heat in convection while the fan runs, slow or incomplete preheating, uneven baking, visible breaks/blisters, or an open circuit on a continuity test
• Designed to cycle under control of the oven's sensor and electronic controls

• Disconnect power at the breaker or unplug the appliance before servicing
• Access may be from the rear of the appliance or by removing the interior panel over the convection fan, depending on the model
• Label and support the two element leads to keep them from retracting into the cavity; ensure terminals are fully seated
• Reuse existing mounting hardware; avoid bending the new element and verify it doesn't contact the oven cavity

This oven door gasket seals the gap between the door and oven frame to keep heat in and temperatures accurate. Replacing a worn door seal restores proper preheat and baking performance and reduces heat escaping around the door.

• Forms a continuous perimeter seal around the oven door opening
• Helps maintain set temperature and proper preheating
• Reduces heat, odors, and smoke leaking from the door edges
• Common signs of failure: frayed or flattened gasket, visible gaps, heat escaping, longer cook times or uneven results

• Safety first: Disconnect power or gas and let the oven cool completely
• Open or remove the door per your model's instructions for access
• Remove the old gasket and clean the channel or mounting points
• Install the new gasket evenly without stretching; confirm the door closes and seals uniformly

This black door handle restores a secure, comfortable grip and a clean, factory look to your appliance's door. Replace a cracked, loose, or damaged handle to keep the door easy to operate and the exterior looking right.

• Provides the handhold used to open and close the door
• Attaches to the door with screws; designed to replace a broken, cracked, missing, or loose handle
• Common symptoms: handle broken, wobbling, missing, or finish damage/scuffs
• Restores appearance without affecting door latch or seal function

• Disconnect power before servicing and allow the appliance to cool completely
• Access handle fasteners per your model (often from the inner door panel); support any glass or trim
• Keep track of spacers and screws for reassembly
• Tighten mounting screws evenly; do not overtighten; verify smooth door operation

This oven temperature control thermostat regulates heat by cycling the elements to maintain your set temperature. Replacing a worn thermostat helps restore accurate baking and consistent, reliable oven performance.

• Senses oven temperature and opens/closes contacts to hold the selected setting
• Can resolve inconsistent baking results, extended preheat, or erratic cycling
• In some failures, the oven may not heat at all

• Disconnect power at the breaker and allow the appliance to cool before service
• Access the control area; move wires to the new thermostat one at a time to match positions
• Route and secure the sensing probe/tube along the original path and retainers; avoid kinks or sharp bends
• After installation, verify temperature with an oven thermometer and calibrate per service instructions if needed

This replacement fan blower drives the microwave's venting and cooling airflow. The motorized blower moves air through the unit to protect internal components and exhaust steam and odors—restoring proper airflow and reducing noise when the original fails.

• Provides forced airflow to cool the magnetron/electronics and vent cooking vapors
• Symptoms of a failing blower: weak or no airflow at the vent, loud rattling/squealing, or excessive vibration
• Inadequate airflow can cause the unit to overheat and shut off until cooled
• Also commonly referred to as the blower motor/assembly

• Disconnect power before service; microwaves can retain dangerous high voltage even when unplugged
• Access often requires removing the microwave from its installation
• Set the blower orientation to match your venting configuration (recirculating/top/rear) per your service manual
• Transfer any mounting hardware or seals from the original part if needed

This 250V 15A safety fuse protects the appliance's line circuit from overcurrent. When the original fuse has blown, replacing it can restore power and help safeguard internal components from further damage.

• Opens the circuit if excessive current or a short occurs, protecting internal parts
• Common symptom: unit completely dead—no display, lights, or response to controls
• Blown fuse will test open (no continuity) with a multimeter
• If a new fuse blows again, another component may be shorted and needs diagnosis

• Unplug the appliance before servicing; microwaves can retain a dangerous charge—discharge the high-voltage capacitor
• Access the fuse near the line filter/control area; note clip orientation
• Replace only with the same 250V 15A rating; never bypass or upsize the fuse
• If the replacement fuse blows immediately, stop and troubleshoot the root cause

Replacement fan blade that mounts to the motor shaft to circulate air inside the appliance, restoring airflow and reducing vibration or noise from damaged or bent blades. Works with the fan motor to help maintain proper cooling and ventilation. What it does:

• Spins on the motor shaft to move air through the appliance's cabinet or evaporator area.
• Restores even airflow for more consistent cooling and performance.
• Reduces excessive noise and vibration caused by cracked, warped, or missing blades.
• Helps prevent airflow-related issues such as warm spots or slow cooling when the fan is not operating properly.

• Disconnect power to the appliance before servicing to avoid electric shock or injury.
• Remove interior panels or housing to access the fan; handle the blade carefully — edges can be sharp.
• Slide the blade onto the motor shaft and secure per OEM method (set screw, clip, or hub); ensure proper alignment and rotation direction.
• Test fan operation after installation and reassemble panels securely.

This replacement range handle restores a secure, easy-to-grip handle for ranges that use part WB15X10225. It returns normal door operation and improves safety and usability for ovens with a damaged or missing handle. What it does:

• Replaces a cracked, broken or loose range/oven door handle.
• Provides a stable gripping surface for opening and closing the oven door.
• Stops handle wobble and prevents accidental detachment during use.
• Matches the factory-style fit and function for straightforward replacement.

• Disconnect power to the appliance before beginning any repair.
• Follow the range/oven manufacturer's door-removal and reassembly instructions when required.
• Basic hand tools are typically required; handle screws fasten securely to the door.