General Electric Washer Control Board

Mounted control board assembly that manages the appliance's electronic operations and user controls. Replaces a failed or damaged control board to help restore proper electronic control, user interface response, and normal cycle operation. What it does:

• Acts as the appliance's main electronic control, sending signals to motors, valves, heaters, and sensors.
• Replaces a faulty board that causes unresponsive controls, blank or error-filled displays, or failure to start cycles.
• Addresses intermittent operation or unexpected stops that trace to electronic control failures.
• Interfaces with the user control panel and system sensors to coordinate timed operations.

• Always disconnect electrical power (and water supply if applicable) before servicing the appliance.
• Handle the board by its edges and avoid touching contacts; use proper ESD precautions when available.
• Take photos of wiring and connector locations before removal to ensure correct reassembly.

This authentic replacement part is a timer for washing machines. The timer is the part that controls the desired time of the wash cycle. Over time, a timer can become inoperable after excessive use. If the timer is no longer performing its intended function, it will need to be replaced.To replace the timer, start by removing the control panel of the washer by removing the mounting screws. Once the screws have been removed tilt the control panel up to gain access to the timer. Once located, take a pair of needle-nose pliers and grab the centerpiece that rotates. Once the pliers have locked onto the centerpiece, proceed to pull off the timer knob from the front of the control panel. Then pull the timer dial off. Disconnect the two wire harnesses. Once these wires have been removed, slide the timer out from its place. Take the new timer and line it up with the four mounting tabs. Slide it in so the locking tabs lock into place. Reinsert the wires in their correct terminals and secure the control panel.This genuine OEM part is sourced directly from the manufacturer and is compatible with General Electric, Hotpoint, and RCA brand washing machines.

This mounted control board assembly regulates key refrigerator functions and replaces a failed main electronics module to restore normal operation. It provides direct control of compressors, fans, defrost cycles and user interface signals. What it does

• Manages compressor and evaporator fan operation to maintain proper cooling; failure can cause no cooling or intermittent cooling.
• Controls defrost cycles and heater operation; faults may lead to excessive frost or failed defrost.
• Processes user inputs and status signals; symptoms include unresponsive controls, blank/erratic displays, or error codes.
• Routes power and communication between system components; failure may cause appliances to not start or behave unpredictably.

• One mounted control board assembly as shown.

• Disconnect power to the appliance before starting any work to avoid shock or damage.
• Handle the board by the edges and avoid static discharge; use grounding precautions if possible.
• Reconnect all harnesses to their original locations and secure the board to its mounting points.

This coin-op control assembly replaces the coin collection and cycle-start control used on commercial laundry machines to restore timed wash cycles and coin-operated functionality. It helps machines accept payment and start selected cycles reliably. What it does:

• Controls coin validation/acceptance and enables cycle start when required payment is received
• Activates timed wash or dry cycles via the machine's timer circuit
• Commonly used when washer/dryer fails to start, does not accept coins, or cycles won't initiate
• Interfaces with the machine's wiring harness and timer to manage payment-to-start operation

• Disconnect power and follow lockout/tagout procedures before installation
• Verify harness connectors and mounting orientation before finalizing installation
• Handle electrical connections carefully; ensure all connectors are fully seated

This ATC temperature control board regulates the refrigerator's temperature and ensures consistent cooling cycles by directing fans, compressors, and defrost operations. Replaces a failed control board to restore normal temperature control and cycle timing. What it does:

• Controls thermostat signals to the compressor and evaporator fan for stable internal temperatures
• Manages defrost cycles and related heater operation if applicable to the model
• Helps stop erratic cooling, excessive frost buildup, or continuous running when the board fails
• Works as the electronic decision hub when mechanical thermostats are replaced by board-driven control systems

• One ATC temperature control board (WH12X10386)

• Disconnect power and unplug the appliance before starting any repair
• Handle the board by its edges and avoid touching circuitry to prevent ESD damage
• Verify harness connector orientation and secure all plug connections; do not force connectors