General Electric Washer Dryer Combo Parts

This is the complete door assembly for a dryer, including the outer panel, inner panel, and handle. It seals the dryer drum compartment to contain heat and tumbling clothes during a drying cycle. Replace this assembly if the door is cracked, warped, won't latch properly, or if the window or seal is damaged.

This is a self-tapping sheet metal screw (8-18) used to secure internal components within the dryer. It threads into metal panels or brackets to hold parts firmly in place during operation. Replace if the screw is stripped, missing, or corroded, which can cause loose panels, rattling noises, or components shifting out of position.

Plastic socket that holds the suspension rod ball in your washer. Replace if worn, cracked, or deformed to restore proper tub support and alignment.

Replacement clip cover that snaps over mounting clips to conceal hardware on your washer dryer combo. Restores finished appearance when original is cracked or missing.

Washer won't change cycles or settings not responding? This selector switch routes power to temperature and speed controls. Moderate DIY repair.

Support assembly stabilizes the washer drum and inner tub components. Replace if cracked, worn, or causing misalignment during operation.

Secures the drain hose in place to prevent kinks, rubbing, and leaks. Replace if hose sags or moves during cycles. Verify fit with your model number.

This SCR (silicon controlled rectifier) is a replacement power-control semiconductor used in appliance circuits to switch and regulate current. It restores proper control of heater/motor circuits when the original SCR fails. What it does:

• Controls current flow in high-power appliance circuits for timed heating or motor control.
• Replaces a failed SCR that causes intermittent or no power to the controlled component.
• Common symptom: appliance elements or motors do not turn on or cycle correctly.
• Common symptom: visible burn, cracking, or open circuit at the SCR.

• Disconnect power to the appliance before accessing electrical components to avoid shock.
• Handle the SCR carefully to avoid static or mechanical damage; use original mounting and hardware.

Replace your washer dryer combo's cracked or worn 27-inch inner basket assembly. Restores the spinning drum that holds clothes during wash and spin cycles.

Mounting bracket that secures the control assembly in your laundry center. Replace if cracked, broken, or worn to restore proper panel alignment.

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

Terminal block mounting screw for dryers and washer dryer combos. Secures the terminal block to the dryer frame. Replace if stripped, missing, or damaged.

This motor and pulley kit replaces a dryer's failed drive motor and pulley assembly to restore drum rotation and normal drying performance. Designed as a direct-fit service kit for compatible GE dryers. What it does:

• Replaces the dryer drive motor and pulley to restore drum tumbling.
• Restores proper belt drive and helps recover normal drying and ventilation.
• Can stop or reduce symptoms like a drum that won't turn, loud grinding, or a dryer that runs but doesn't tumble.
• Designed to work with the dryer's existing belt and mounting hardware when applicable.

• One motor and pulley kit

• Disconnect power to the dryer before starting any repair.
• Basic hand tools are typically required; remove the dryer cabinet or access panel as needed.
• Support the drum while replacing the motor; follow the appliance's service manual for routing the belt and aligning the pulley.

This is an electrical plug connector used in the dryer's wiring system. It provides a secure connection point for internal wiring to ensure proper electrical flow to dryer components. Replace this plug if it is burned, melted, cracked, or if you are experiencing intermittent power issues with the dryer.

Secures the front panel on dryers. Replace if the panel is loose, rattling, or won't stay in place. Confirm fit with your model number before ordering.

A replacement pan head screw used to fasten appliance panels and components. Its standard #8 coarse thread and 3/8-inch length secure trim, brackets, and small assemblies for stable operation. What it does:

• Fastens panels, brackets, and small parts in household appliances
• Replaces stripped, rusted, or missing #8-18 pan head screws
• Restores secure mounting where vibration or wear caused looseness
• Works with sheet-metal or threaded inserts designed for #8-18 screws

• Disconnect power to the appliance before beginning any repair
• Use the correct #2 Phillips or compatible driver to avoid cam-out
• Thread in straight and tighten until snug; avoid over-tightening to prevent stripping
• Keep small screws away from children and dispose of old fasteners safely