General Electric Washer Dryer Combo Parts

5/16-18 hex screw secures panels and components in laundry centers. Replace stripped, broken, or missing fasteners to restore proper fit and alignment.

Hex pan thread screw for washer dryer combo units. Secures panels and components to the frame. Replace missing, stripped, or damaged fasteners.

Protective cap stud cover for washer dryer combo units. Shields electrical or mechanical studs from debris and maintains secure connections. Replace if cracked, broken, or missing.

Main wire harness for washer dryer combos. Connects electrical components throughout the unit. Replace if wires are frayed, damaged, or connections are loose.

The Baffle is an OEM part for GE electric dryers. Located inside the dryer drum, it helps separate clothes and improves air circulation during tumbling cycles. 

To achieve consistent drying times, a dryer relies on balanced airflow penetrating all areas where clothes reside. The baffle creates divisions to ensure air fully surrounds each layer instead of bypassing some areas. Its raised ridges also help tumbling action by preventing clumps of clothes.

Symptoms of a bad baffle include:

• Slow, uneven drying requiring extra cycles  
• Certain areas of clothes remain damp while others over-dry
• Reduced airflow output from the vent due to blockage

Replacing it with the genuine GE baffle plate restores optimized air distribution within the drum. The part is also compatible with some Kenmore dryers that use GE elements.

Secures wiring and hoses in your laundry center to prevent rubbing and wear. Replace when broken or missing to maintain proper routing. Verify fit.

Retaining clamp secures hoses and tubes to prevent leaks and loose connections in your washer dryer combo. Replace if worn or damaged. Verify fit with model.

The Top Bearing is an OEM part for GE electric dryers. Located near the top of the drum assembly, it further supports rotational movement during tumbling.

Symptoms of a faulty top bearing include:

• Emergence of grinding or scraping noises from the upper drum area
• Resistance or lack of responsiveness to smooth drum spinning  
• Potential impacts to interconnected spinning components  

As a bearing used repeatedly over time, standard wear from lint and dust accumulation affects function. Impacts can also compromise integrity on occasion. 

Causes typically include normal wear and tear from prolonged rotational cycles. Heavy loads may accelerate deterioration too by adding strain.

This genuine GE replacement bearing restores reliable support at the top of spinning cycles. Compatible with some Hotpoint, RCA, and select Kenmore dryers too, it extends equipment life through dependable bearing operation once installed.

This lid bumper cushions the lid of your top-load washer as it closes, absorbing impact to reduce slamming noise and protect the top panel's finish. Replace a worn or missing bumper to restore smooth, quiet lid operation. What it does

• Absorbs impact between the lid and cabinet to reduce slamming and vibration noise
• Helps protect the top panel finish from chips and scratches near the lid area
• Restores proper cushioning when the original bumper is missing, cracked, or flattened
• Common symptoms: lid slams or clunks when closing, increased noise, visible missing bumper

• 1 lid bumper

• Disconnect power before servicing
• Open the lid and pull the old bumper straight out of its mounting hole; needle-nose pliers can help if it's stuck
• Clean the hole and surrounding surface for a secure fit
• Press the new bumper fully into the hole until seated flush; for even cushioning, consider replacing both if your model uses two

Replaces damaged or worn control panel face on laundry centers. Restores front appearance and provides secure mounting for controls. Needed when cracked or broken.

This right-hand hinge washer cover protects and conceals the hinge area on the washer lid, restoring a finished appearance and preventing dirt or moisture from contacting the hinge assembly. What it does:

• Covers the right-side hinge/washer area to keep debris and moisture out of the hinge assembly
• Helps maintain proper lid alignment and reduces exposed sharp edges
• Restores the washer's cosmetic finish after damage or wear
• Can eliminate rattling or rubbing caused by a missing or broken cover

• One right-hand hinge washer cover

• Disconnect power to the appliance before starting any repair
• Remove the washer lid or access panel per the manufacturer's instructions to reach the hinge area
• Fasten the cover using the original screws/clips; do not force or overtighten plastic tabs
• If other hinge components are damaged or loose, inspect and replace as needed for a safe repair

Secures front panel on laundry centers. Replace if broken or panel becomes loose. Verify fit with your model number before ordering this clip.

This is a complete dryer door assembly for a laundry center or combo unit. It includes the outer door panel, inner panel, and associated hardware needed for a full replacement. Replace this assembly if the dryer door is cracked, warped, won't latch properly, or has a broken hinge.

Secures and routes the drain hose in your washer dryer combo. Replace if the original stop is cracked, broken, or missing to properly support the hose.

Left-side hinge cover for laundry center washer lids. Restores appearance and protects hinge assembly. Replace if cracked, broken, or missing.

Control panel front cover for washer dryer combos. Restores finished appearance and protects buttons and displays. Replace when cracked, broken, or worn.