General Electric Washer Hose Or Tube

This hose overflow kit redirects excess water from the refrigerator's drain area to the drain pan, helping prevent puddles and water damage behind or under the appliance. Fits common GE refrigerator drain/overflow applications. What it does

• Provides a dedicated path for excess defrost and condensation water to the drain pan
• Helps stop water pooling under or behind the fridge that can indicate a blocked or misrouted drain
• Useful when replacing a cracked, split, or missing drain/overflow hose
• Restores proper water routing after service to the defrost drain or water system

• One hose overflow kit

• Disconnect power and shut off the water supply before starting service
• Route hose from the drain/overflow outlet to the drain pan following OEM routing; secure with supplied clamps or retainers
• Inspect or replace any related grommets or seals to ensure a watertight fit
• Test for proper drainage and check for leaks after restoring power and water

This outside drain hose directs wastewater from your washer to the household drain. Replace a cracked, kinked, or leaking hose to stop leaks and restore reliable draining at the end of each cycle.

• Routes discharge water from the drain pump to a standpipe, laundry tub, or sink
• Helps maintain proper flow during drain/spin to prevent backups
• Common signs of failure: water leaking behind the washer, slow or incomplete draining, or drain-related error messages
• Visual clues include cracks, pinholes, bulges, or severe kinks

• Disconnect power and water; pull the washer forward for access and place towels/bucket as needed
• Note hose routing and connection points; release clamps and remove the old hose
• Fully seat the new hose; reuse existing clamps/hangers as required. Route without kinks and maintain proper standpipe height
• Run a test drain/rinse and check all connections for leaks

This siphon pipe is a washer drain component that forms part of the air-break assembly. It helps prevent unintended siphoning and backflow so the tub drains correctly without pulling water back in or continuously draining. What it does:

• Provides the pipe section of the washer's siphon break/air gap
• Maintains airflow to stop siphoning and backflow during drain and spin
• Supports consistent, complete draining
• Typical failure signs: leaks near the siphon break, cracking, or water draining back into the tub

• Includes one siphon pipe

• Disconnect power and turn off water before servicing
• Expect some residual water; have towels or a pan ready
• Note hose routing; transfer any clamps/fittings from the old pipe and seat connections fully
• After reassembly, run a brief fill/drain to check for leaks and proper draining

This pump hose channels washer tub water to the drain pump, restoring proper drainage and preventing leaks at the pump connection. Durable flexible tubing designed to match factory fit and routing. What it does:

• Transfers wash water from the tub to the drain pump for normal draining
• Replaces cracked, collapsed, pinched, or leaking pump hoses that cause poor drainage
• Helps stop leaks that can occur where the tub outlet connects to the pump
• Restores reliable water flow when the original hose is brittle or damaged

• Disconnect power and water before installing; follow all safety precautions
• Inspect clamps and surrounding fittings; replace clamps if damaged or corroded
• Ensure proper routing and secure clamps to avoid kinks or contact with moving parts
• Test a short cycle after installation to check for leaks

This vent hose directs dryer exhaust from the appliance to the home vent, helping remove moisture and lint so clothes dry efficiently and the dryer runs safely. It replaces a worn or damaged exhaust connection. What it does

• Channels hot, moist air from the dryer to the exterior vent to prevent moisture buildup.
• Helps reduce drying times when unrestricted and properly installed.
• Prevents lint accumulation at the appliance connection when intact.
• Common symptom: longer drying cycles or dryer overheating when the hose is crushed, disconnected, or damaged.
• Common symptom: visible lint buildup around the dryer outlet or exhaust connection.

• One vent hose.

• Disconnect power (and gas, if applicable) before servicing the dryer.
• Inspect clamps and the vent path; replace any damaged clamps or crushed ducting.
• Avoid sharp bends or kinks; maintain a smooth, short run for best airflow.
• Wear gloves to protect hands from sharp edges and lint; follow all manufacturer safety instructions.

This water inlet pipe routes water from the refrigerator's supply to the dispenser and ice-making system, helping restore proper water flow and stop leaks at the inlet tubing. Durable molded tube designed to match factory fit. What it does:

• Carries water from the household supply to the fridge's dispenser and ice maker
• Replaces cracked, pinched, or corroded inlet tubing that can cause leaks
• Restores water flow when a damaged inlet pipe prevents dispensing or ice production
• Matches OEM shape to align with mounting points and fittings

• Turn off and disconnect power to the appliance before servicing.
• Shut off the water supply and drain remaining water from the line before removing the old pipe.
• Inspect and replace any worn seals, clips, or fittings; tighten connections to OEM torque specifications.

This U-shape drain hose hanger secures the dishwasher drain hose to the cabinet or sink rim so the hose stays in the correct position and helps prevent kinks or improper drainage. A simple replacement that restores proper hose routing. What it does

• Holds the drain hose in a U-shaped loop to maintain proper high-loop or air gap positioning
• Keeps the hose away from sharp edges and hot components to reduce wear
• Helps prevent hose kinking that can cause slow draining or backups
• Useful when existing hanger is cracked, broken, or missing

• One U-shape drain hose hanger

• Turn off power to the appliance before accessing the drain hose area
• Typically installs by clipping or snapping around the hose and attaching to cabinet/sink edge—no special tools required
• Inspect the hose for damage and secure hose routing when replacing the hanger