General Electric Hose Or Tube

Replaced hose with new one from Appliance Parts. Delivery was exceptionally fast. Appliance was up and running next day. Read more

• Leaking
• Ice maker not making ice

I made the right initial move - I went to appliancepartspros.com and located the necessary parts. A video convinced me I could make the repairs myself. The correct parts were easily ordered and arrived quickly. I had no problem installing the parts using the knowledge I gained from the appliancepartspros.com video and the leak was fixed. Read more

• Leaking

We noticed a puddle of water in front of the fridge a couple of months ago-dried the floor up both times and thought someone had dropped ice-or spilled water. A couple of weeks ago there was water dripping through the dropped tile ceiling in the basement. I shut off the water for the water supply to the fridge at the copper pipe in the basement and removed some of the tiles which felt a little damp. It still dripped all day. When my spouse came home he pulled down more of the tiles. It was as... Read more

• Will not stop filling with water

I replaced the water level switch and hose. After removing the hose, I found that it was clogged, and did not allow the water level to be sensed by the switch. A test after the replacement of the parts was successful. While filling the tub, the water shut off at the small, medium, and large levels as indicated by the switch. Read more

The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more

Our GE was installed about 8 years ago and was AWESOME for much of its early life. However, progressively its cleaning ability diminished. By replacing all the spray arms (clogged with debris), filters, drain hose, and sump...this dishwasher cleans like it did when it was new! Cost was around $100 (also replaced a wheel and the silverware basket) and labor was relatively simple. And to think...my mother-in-law said, "Wouldn't it just be easier to buy a new one?!?". Read more

Replaced the hose and water inlet. Part #: AP3189243 (WH41X10077). This connects the solenoid valves to bring water into the tub. Read more

• Leaking

Fridge is 14 years old, ordered the water valve assembly and hose. Removed and replaced both Read more

Pulled down the existing drain tube and installed new one. Tight area so it requires two hands to push up and attach the new tube. The short rubber tubing attached to the new drain tube has to fit snug onto the plastic tube connection that hangs down. Replacing the water dispenser tray is simple and no explanation needed, Read more

• Leaking

I replaced the pump drain assembly. The flapper valve was included in the assembly, so I did not need to order that. On previous repairs, the old drain hose was tricky to reinstall, so I replaced it and the hose clamp.The silverware basket had holes in the bottom and required replacement. I had some broken tine clips. Read more

With new hose Read more

Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more

First of you need to remove front panel of the washer, using a putty knife push the tabs between the top of the machine and the front panel. Once front panel is exposed drain hose is connected to pump which is in the front of the machine,very easy to access with the front off. Remove old hose with pliers and discard ,run new hose thru outlet on the back of the machine and secure new hose to drain and secure hose to the machine, reinstall front panel of washer and that's it Read more

I replace the water inlet valve in my refrigerator about 8 months ago. About a week ago, the old plastic water line broke. I forgot how the water line connector worked and broke the valve trying to pull it out. I got a new valve and replacement water line, and it went in easily, just like the video said. Morals of the story: 1. Know how to remove the old plastic water line. I could have saved myself the price of a new valve if I'd remembered how the connector worked. Unless you have a really... Read more

Replaced the drain pan below the evaporator coil (it was rusted to the point had a hole in it) and decided to replace both drain tubes since I had to open up the back panel. The video on the website was very helpful. Thanks!! Read more

Thanks to the AppliancePartsPro, I ordered it online and received it quickly. I even used the step by step directions on how to replace the tube from the AppliancePartsPro website. Just be very careful and review the instructions first. Couple of important things: 1. Take a picture of the existing wiring and tubes before you take them apart. 2. *if* you remove the wires ( red and white plugs) from the valve, make sure you plug them back in correctly. 3. Do not pull or push the tubes hard. Use... Read more