General Electric Washer Parts

If your washer's infusor is loose or coming up during spin cycles, the assembly may be worn or stripped. Simple 10mm socket replacement in minutes.

Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.

Washer won't advance through cycles or gets stuck? Timer controls wash cycle progression. Quick DIY repair—remove lid, unplug harnesses, swap timer.

Fix a washer that won't cycle, skips rinse, or drains while filling. This mechanical timer restores proper cycle sequencing. DIY repair in 20 minutes.

Fix a washer that leaks, overfills, or won't fill properly with a new triple water inlet valve. DIYers report 10-15 minute installations.

This pump and brake assembly drains water from the tub and applies the basket brake in your top-load washer. Replacing a worn assembly restores proper draining and a safe, prompt basket stop between cycles. What it does

• Pumps water out of the washer during drain and spin phases
• Applies the brake to stop the spin basket between cycles or when the lid switch is activated
• Helps reduce extended coast-down and stopping squeal
• Typical symptoms: standing water, slow/no drain, leaking at the pump area, basket coasts too long or squeals when stopping

• One pump and brake assembly

• Disconnect power and water supply; drain remaining water from hoses before service
• Access from the washer's underside; support the unit securely
• Transfer existing hoses/clamps to the new pump and secure all connections; if belt-driven, verify proper belt routing and pulley alignment
• Run a brief fill/drain test and recheck for leaks and proper basket stop

Replaces the control panel buzzer that produces audible beeps and alerts. Needed when the existing buzzer is cracked, broken, or no longer chiming properly.

This machine screw secures panels, brackets, and internal components in compatible washers. Replacing a missing or stripped fastener restores a tight fit to help reduce vibration and keep parts properly aligned.

• 10-32 thread; 5/8-inch length; Torx T25 drive
• Fastens components and panels to resist loosening from vibration
• Replaces lost, corroded, or stripped screws
• Helps address loose or rattling panels, misalignment, or hardware that won't tighten

• Unplug the appliance and turn off water supply before servicing
• Use a T25 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten
• Repair or replace the bracket/panel for a secure hold

Replace your washer tub seal to stop leaks between inner and outer tubs. Install when you notice water pooling or moisture around the drum. Verify fit.

Plastic bushing that fits inside your washer's lid hinge for smooth pivoting. Replace if worn, cracked, or causing lid misalignment and squeaking.

Secures the drive pulley to the transmission shaft in top-load washers. Replace if the original nut is backing off, stripped, or missing.

Seals the outer tub to prevent leaks during spin and drain cycles. Replace if washer leaks from the center or bottom. Confirm fit with your model number.

The DRAIN PUMP is an OEM component specifically designed for GE washers. It is located near the base of the unit and functions to remove water from the wash tub at the end of cycles. The drain pump works vigorously to expel soiled water through the drain hose for hygienic cleaning.  

Symptoms of a bad drain pump include:

• Water remaining in the tub even after cycles have finished running  
• Drain hose that is not effectively carrying away water
• Strange gurgling or churning noises coming from below the unit
• Possible leakage from seals or connections near the drain area

Causes can include internal blockages from built-up debris, wearing of impeller seals or motor, or physical damage impairing pump functionality.

Replace yours today with this genuine OEM GE part for thorough water extraction and machine drainage after every load. This GE replacement part is compatible with Hotpoint, RCA, and select Kenmore models.

Damper shock absorber for washers. Mounts between outer tub and base to cushion spin motion. Replace if cracked, leaking, or weakened to restore stability.

Fixes no water filling, loud whistling during fill, or slow fill issues. This dual solenoid inlet valve controls water flow. Moderate DIY repair.

Fixes washer not spinning fast enough or motor failure. This 2-speed direct drive motor restores proper agitation and high-speed spin cycles. Moderate DIY.