General Electric Washer Screws, Nuts, Washers

Size: 1/4 - 20 b.

Size: 8-18 b.

This is a package of 12 screws each paired with a washer—small fasteners used to secure panels, trim and components on compatible appliances. Replacing missing or stripped screws restores proper fit and reduces vibration or rattling. What it does

• Secures panels, trim pieces, brackets and small components in place
• Washer helps distribute load and prevents screw heads from pulling through thin materials
• Fixes symptoms like loose panels, rattling parts, or missing hardware
• Use matching screws when reassembling after repair to ensure correct fit

• One package containing twelve screws with washers

• Power off and unplug the appliance before starting any repair
• Hand-start screws to avoid cross-threading; finish snugly but do not overtighten
• Keep removed hardware organized and replace with the correct size and thread type rather than forcing the fastener

Specs: 8-32 ca hxw 1/2

This is a replacement screw used to secure appliance components and panels so parts stay properly attached for safe operation. It's a direct-fit fastener matching OEM form and function. What it does

• Secures panels, trim, or internal components to prevent rattling or gaps
• Restores factory attachment where a screw is missing or stripped
• Helps maintain proper alignment of housing and service access
• Suitable when repair requires original-fit fasteners

• Disconnect power or unplug the appliance before servicing to avoid shock
• Use the matching screwdriver or bit to avoid stripping the head
• Thread carefully and avoid overtightening to prevent damage to threads or plastic parts
• Keep removed screws organized; replace only the screws that match the original locations

Size: 8-18 b.

A small M5 x 12 machine screw used to secure panels and components in compatible appliances. Simple, serviceable hardware that helps restore proper fit and stops rattling or loose parts. What it does:

• Fastens panels, brackets, or components where an M5 x 12 machine screw is specified
• Restores secure attachment when original screw is missing, loose, or damaged
• Helps eliminate vibration noise and misalignment caused by loose hardware
• Fits into pre-tapped holes designed for M5 machine-threaded fasteners

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or hex driver to avoid stripping the head
• Install straight and tighten snugly; avoid over-tightening which can strip threads or crack plastic
• If threads are damaged, replace the mating fastener or insert as needed before reuse

This is a replacement washer used with appliance fasteners to secure and space components for stable operation. Installing a correct washer helps maintain proper fit and reduces wear at connection points. What it does:

• Provides a stable bearing surface between a fastener and the mounted part
• Helps maintain correct gap/spacing for aligned components
• Reduces wear and prevents metal-on-metal contact at the joint
• Can stop loosening that causes vibration or rattling near fastened panels

• Disconnect power and water before accessing internal components.
• Use the correct matching fastener and size; do not substitute an incorrect diameter or thickness.
• Hand-start fasteners to avoid cross-threading, then torque to manufacturer specs; avoid overtightening.
• If multiple washers or fasteners show wear, replace all affected hardware for best results.

A standard M3 hex nut used to secure compatible M3 bolts and studs in appliance assemblies. Small but essential, it restores proper fastening where a worn, stripped, or missing nut causes loose panels or components. What it does:

• Secures M3 threaded fasteners to hold panels, brackets, or small components in place
• Replaces missing, stripped, or corroded nuts that allow vibration or movement
• Helps stop rattling, misalignment, or intermittent electrical/contact issues caused by loose parts
• Used wherever an M3 nut is specified by the appliance manufacturer

• Disconnect power and follow appliance safety instructions before accessing internal parts
• Use the correct M3 bolt and matching thread engagement; avoid cross-threading
• Tighten snugly but do not overtighten to prevent stripping threads or damaging parts
• Replace any accompanying damaged fasteners or hardware for a reliable repair