General Electric Washer Screws, Nuts, Washers

This motor mounting screw secures the motor to the appliance chassis so the motor stays aligned during operation. It's a direct-fit fastener that replaces worn, stripped, or missing motor screws to restore secure motor mounting. What it does:

• Fastens the motor to the appliance frame to maintain correct motor alignment and stability
• Prevents motor movement that can cause vibration, noise, or premature wear
• Replaces missing, damaged, or corroded motor mounting hardware
• Helps restore reliable operation after motor service or reassembly

• Disconnect power before servicing the appliance to avoid electrical shock or injury
• Use the correct screwdriver or socket to avoid stripping the screw head
• Inspect mating threads and replace any damaged hardware or stripped inserts before final installation
• Tighten to secure fit; avoid over-tightening which can strip threads or crack housings

This ST4 x 20 screw replaces a lost or damaged fastener and secures panels or brackets in your washer, restoring a tight fit and helping eliminate vibration and rattling caused by loose hardware.

• Fastens panels, brackets, or covers to the washer cabinet
• Replaces missing, stripped, or corroded screw specified as ST4 x 20
• Helps keep components aligned to reduce vibration and noise
• Useful during reassembly when the original screw won't hold

• Disconnect power before servicing; turn off the water supply.
• Match the screw length and thread to the original location; do not mix different screws.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Transfer any original spacers or washers used with this screw.

This M5-16 metric machine screw secures service panels and internal components in compatible appliances, providing reliable fastening for repair and replacement. Use the correct screw to restore fit and function after disassembly or part replacement. What it does

• Fastens panels, brackets, and components where an M5 x 16 mm machine screw is specified
• Restores secure attachment after repair or replacement of parts
• Helps eliminate rattles, loose panels, or misaligned parts when the correct screw is used
• Small, corrosion-resistant finish (typical for appliance screws) for lasting hold

• One M5-16 machine screw

• Use the correct sized M5 driver or hex bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or component damage
• Disconnect power and follow appliance safety procedures before accessing internal parts
• If the original screw had washers or clips, reuse them or replace with equivalent hardware

A replacement M12 x 25 flange bolt used to secure appliance components where a washer-style bolt head is required. Durable fastener that restores proper fit and helps stop movement or vibration in assemblies. What it does:

• Secures panels, brackets or assemblies that use an M12 flange-style fastener.
• Restores proper clamping force when an original bolt is stripped, corroded, or missing.
• Helps eliminate rattling, loose parts, or misalignment caused by a failed fastener.
• Works wherever a metric M12 x 25mm flange bolt is specified by the manufacturer.

• One flange bolt (M12 x 25)

• Disconnect power and follow manufacturer safety instructions before servicing.
• Use the correct socket or wrench to avoid rounding the head; tighten to the appliance manufacturer's torque specification.
• Inspect mating threads and replace if damaged; do not force a damaged bolt.
• If the OEM manual calls for threadlocker or a specific torque, follow those instructions.

Size: 8 - 18 ab.

Nickel

Small self-tapping screw used to secure appliance panels and internal components. Replaces worn or missing fasteners to restore proper fit and alignment for covers, brackets, and trim pieces. What it does

• Secures sheet-metal panels, brackets or trim to the appliance chassis
• Replaces stripped, corroded or missing screws that allow rattling or loose parts
• Helps restore proper panel alignment and prevents vibration noise
• Works where a self-tapping thread is required in thin metal or plastic mating parts

• Power off and unplug the appliance before servicing
• Use the correct screwdriver bit to avoid cam-out and head damage
• Start threads straight and drive carefully—do not overtighten to avoid stripping
• Replace like-for-like; match screw length and thread type to the original

5/16-18 tpt ihw s n

This is a replacement self-tapping screw used to secure panels, brackets and small components on compatible appliances. It provides a direct-fit fastener for repairs where the original ST4 x 25 mm screw is missing or damaged. What it does

• Fastens trim, access panels, brackets and internal components that use an ST4 x 25 mm self-tapping fastener
• Restores proper fit and reduces rattles or loose parts caused by stripped or missing screws
• Matches the OEM thread and length for a secure hold in sheet metal and plastic mounting points
• Useful for routine appliance repairs and refurbishments

• Use the correct size screwdriver or bit to avoid stripping the head
• Start threads slowly and avoid over-torquing to prevent stripping or cracking mounting material
• Ensure the appliance is unplugged or power is disconnected before servicing
• Keep removed hardware organized to verify correct replacement locations