We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.
Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more
Installation tool designed for installing washer drive belts. Provides proper leverage and positioning to seat belts correctly on pulleys and motor shafts.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
This shaft and tube assembly supports and drives the washer's inner basket during the spin cycle. Replacing a worn or bent assembly restores smooth rotation and helps reduce noise, vibration, and basket wobble.
After researching the problem on this site, I realized that the most likely cause was a bad bearing contained in the shaft & tube assembly. Essentially, the tub seal failed & allowed water to travel down the shaft & into the housing containing the bearing. I confirmed this by pulling the front cover off of the unit & noticed some brown water pooled directly under the shaft & tube assembly. I followed the disassembly instructions on this site & it wasn't too bad but did take some time as pretty... Read more
Internal drain hose channels water from washer tub to external drain system. Replace if cracked, kinked, or leaking to restore proper drainage function.
The Check Valve Flapper is an OEM replacement part for GE dishwashers. It is a small but crucial component located within the water inlet valve assembly. The check valve flapper regulates water flow into the dishwasher, allowing water to enter during the fill cycles but preventing backflow when the water is drained.
Causes of a bad check valve flapper can include wear and tear over time, mineral buildup that causes sticking, or damage to the flapper itself. This prevents the flapper from opening and closing as intended.
Symptoms of a bad check valve flapper include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.
Pulled dishwasher from the cabinet and flipped onto its side. Easy access to sump and drain flapper valve that I also replaced. Rubber sump coming apart into soft pills & chunks and plugging spray arms. Better now but it's rediculous that GE would make components that dissolve this way. Read more
Fix washer overfilling or not filling properly. This pressure switch controls water level for proper washing. DIY-friendly, takes about 5-10 minutes.
I thought initially it was a hose because it was leaking water from the bottom. On the small and medium load it didn't leak. I watched it on the large setting and noticed the water didn't shut off initially so therefore it was over filling. I ordered a switch pressure switch from Appliance Parts Pros and received it in two days. I replaced the switch, put the washer together and now it works like new. The wife is very happy to have her washer back working better than ever! Thanks! Jerry Read more
Replacement button tree assembly for washer control panels. Restores reliable button function when selector buttons are missing, cracked, or unresponsive.
Replaced button tree. Read more
Labeled control ring for your washer's control panel. Replace when the original dial becomes cracked, stripped, worn, or the cycle indicators are unreadable.
I replaced the Timer knob components. Removing the cover that contains the Timer was simpler than I anticipated. Just remove the screws on the top of the back of the machine. Hold the cover and lift up and push to the left (facing the front of the washer). Removed the Timer Knob Clip with small needle-nose pliers. Grasped the Timer and turned counterclockwise to remove and unplugged the wiring clip. The timer is seated to the cover and held securely in place with one screw. I seated the new... Read more
Fix slow-filling or constantly running water issues with this washer water inlet valve. Controls hot, cold, and warm water flow. DIY repair in 30-60 minutes.
Replaced inlet valve Read more
Plastic support bracket that secures suspension rods to the washer cabinet. Replace when cracked, broken, or worn to restore proper drum suspension.
Leveling leg for top-load washers. Installs at the base to stabilize the unit and adjust height. Replace if cracked, broken, or missing to restore balance.
Replaced washing machine stabilizer feet Read more
Secures the lid lock mechanism on your washer. Mounts around the strike area where the lid lock engages. Replace if cracked, broken, or missing.
Maintains belt tension for smooth drum rotation. Replace if the pulley is cracked, worn, or the nylon bushing is broken to restore proper operation.
I replaced the drum bearing in the back and also the nylon sliders in the front. It rook some time but was not difficult. I took some extra time to thoroughly clean all the lint from the inside. Read more
Drive pulley mounts to the washer basket shaft and routes the belt from the motor. Replace if worn, cracked, loose, or showing play on the shaft.
Replaced the shaft & mode shifter assembly. Also replaced the pulley as it had taken some damage from the wobbling clutch dog. And replaced the tub seal since it's normally inaccessible with the shaft in place. This is an advanced repair that took a lot of time. Removing the tub nut took a 1 11/16" socket and a 700 ft-lb impact wrench and I had to hammer on the nut for several minutes to break it free of the tub. Disassembly of the washer is complete, and requires a lot of space for... Read more
Washer won't start or lid won't latch? This lid lock striker engages the lock assembly to secure the lid during wash cycles. Simple DIY fix.
By GE. Fits many different washer brands and models. Includes insert.
The new GE washers come with a fill valve that has a 1/8" hole for the hot water inlet. This is probably for energy savings or something. So, I installed the older style GE fill valve on my new machine. Since the older style has larger inlet holes for both hot and cold water, it fixed my problem easily. NOTE: The outlet nipple on the new style GE fill valves are larger than the older style. Therefore, I had to make a coupling piece to attach the older style GE valve outlet nipple to the... Read more