We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Suspension rod and spring assembly that supports and stabilizes the washer tub. Replace if rod is broken, spring is worn, or assembly is damaged or missing.
I replaced the suspension rods -- I am NOT particularly experienced with machines of any type, so it took me longer than it might have someone else, but once I figured out what I needed to do, everything went very smoothly. The washer spins like a dream now! Read more
Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Washer won't advance through cycles or stops mid-wash? This timer control assembly manages fill, agitate, rinse, and spin sequences. 15-30 minute repair.
I replaced the Timer knob components. Removing the cover that contains the Timer was simpler than I anticipated. Just remove the screws on the top of the back of the machine. Hold the cover and lift up and push to the left (facing the front of the washer). Removed the Timer Knob Clip with small needle-nose pliers. Grasped the Timer and turned counterclockwise to remove and unplugged the wiring clip. The timer is seated to the cover and held securely in place with one screw. I seated the new... Read more
Suspension rod and spring assembly for top-load washers. Mounts between tub and cabinet to absorb vibration. Replace if cracked, broken, or corroded.
This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.
Replaced the motor with a new one, if I can offer any advice about doing this job, make sure to keep track of where each wire goes on the motor and whatever wires need to be disconnected. There are a few good video's online showing how to do this job and can save you a lot of time and frustration. Read more
Fix a washer that overfills or won't start the wash cycle. This water level pressure switch detects proper fill levels. DIY-friendly repair.
Hmm...watched video after reading on web of running water problem with GE washer....common fail .....moving stuff to get to the washer took all the time, easy fix but a lot of screws to remove and looking time APP site very good, will order again if need be thanks Read more
Fabric softener not dispensing or agitator loose? This washer dispenser cup sits atop the agitator. Simple DIY fix—twist off and replace in minutes.
Planning to spend hundreds on a new washer and was pleased to discover the agitator coupling was the only thing wrong. Very easy repair. The only additional feature we would have liked was a softener dispenser. Located a GE model of the same genre that used the same coupler and took the leap to get the agitator and dispenser cup for this model (WJRR4170). Replaced the old agitator with new one and dispenser cup. Worked perfectly! We now have a washer with dispenser that works great and saved... Read more
Suspension rod and spring assembly for washer drum stability. Replaces worn, broken, or weakened suspension components causing drum movement or sagging.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Supports the washer tub and absorbs vibration during cycles. Replace if corroded, worn, or broken to prevent drum sagging and banging during operation.
Replacement control knob for washing machines. Installs on the control panel to select cycle and temperature settings. Needed when cracked or broken.
Replaced the timer Read more
Control knob assembly for washer timer/cycle selector. Restores secure grip when original is cracked, stripped, or broken. Attaches to timer shaft.
Suspension rod and spring assembly supports the washer tub and reduces vibrations. Replace if cracked, worn, or broken to restore proper tub support.
I replaced all 4 suspension rods and springs and now it spins very smooth. They weren't broken, just badly worn. It gave new life to my 15 year old GE Profile washer. They are basically springs, so they wear after a while. It was well worth the hour I spent fixing it. You need a good long reach to get to the back 2 and you have to take off the dampening straps and the control panel so you can gain access. All in all, I'm happy with the repair, although I though that these parts are bit... Read more
The Mode Shifter & Shaft Assembly is an OEM replacement part for GE washing machines. It is a mechanical component located inside the washer tub that allows for shifting between agitation, spin, and other cycles. The mode shifter and shaft assembly receive input from the control system to precisely change the operational mode at designated points in the cycle. Causes of a bad mode shifter & shaft assembly include worn out or damaged internal gears, stripped or broken shafts, or a loss of integrity in components that restrict smooth shifting between modes. Symptoms of a bad mode shifter & shaft assembly include:
This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
The Triple Water Valve is an OEM part for GE washing machines. This part controls the flow of water into the washer, allowing for the precise mixing of hot, cold, and warm water necessary for different wash cycles.
Causes of a bad triple water valve can include mineral buildup or blockages from debris, electrical issues such as faulty solenoids, and wear and tear from frequent use.
Symptoms of a bad triple water valve include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Ordered water inlet valve. Took all about 10 mins to change it solved the problem. Easy fix Read more
The Rotary Knob is an OEM replacement part for GE or Hotpoint washing machines. It provides the interface for selecting wash cycles and adjusting settings like temperature and spin speed. Causes of a bad rotary knob include cracking, peeling, or damage to labeling from repeated use over time. The internal mechanisms can also wear out, preventing proper rotation. Symptoms of a bad rotary knob are:
It is also compatible with RCA, Westinghouse, Tappan, and some Kenmore models.
Opened back up. Saw aQR code. Made the finding the parts easy Read more
Fix a washer that won't fill with hot or cold water. This rotary temperature switch controls water temperature settings. Easy 5-minute DIY repair.
Replaced the water temperature selector switch. After watching a YouTube video for our GE top loading washer showing the switch replacement, I replace the switch in under 5 minutes! Very easy! Read more