Jade Parts

This ice door spring restores the closing tension on the dispenser chute door. Replacing a fatigued spring helps the flap seal properly after dispensing, reducing warm-air leaks that cause frost buildup and ice clumping around the chute. What it does:

• Provides return tension so the ice chute door closes after dispensing
• Helps maintain a tight seal to limit frost, condensation, and air leaks
• Can resolve a chute door that sticks open/closed or won't fully close
• Reduce rattling or poor ice flow caused by a loose flapper

• 1 spring

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control panel to access the ice door assembly
• Note spring orientation on the flapper; transfer/install carefully without over-bending
• Smooth flap movement and a proper seal before reassembly

• Dispenser door spring
• Flapper spring
• Ice chute door spring

Size: 10-24X5/16-NI

Dishwasher rack mounting strip roller.

Restore safe, smooth door operation with this dishwasher door spring. It counterbalances the door's weight so it opens and closes in a controlled way, preventing a sudden drop when the original spring breaks or fatigues.

• Provides the tension that counterbalances the dishwasher door through the hinge mechanism
• Helps prevent the door from slamming open or feeling unusually heavy
• Restores smooth, even door movement side-to-side
• Typical symptoms: door drops quickly, feels heavier than normal, uneven motion, or a visibly broken/stretched spring

• Disconnect power and shut off water before servicing
• Remove the toe/kick panel to access the hinge area
• Support the door, then move it slightly to relieve tension before unhooking the old spring
• Attach the new spring between the frame anchor and hinge arm; if your model uses two springs, replace both sides for even tension

Color: light gray. Measures about a 1/2 inch high by 4 inches deep.

This dishwasher door seal fits into the tub channel to create a tight, water-resistant barrier when the door closes. Replacing a worn gasket helps stop nuisance leaks and restores proper door compression and moisture containment.

• Creates the primary seal around the dishwasher tub opening when the door is closed
• Helps keep wash water, suds, and steam inside the wash cavity
• Wear can lead to drips at the front corners or along the sides
• Replace if the gasket is cracked, torn, flattened, or no longer sealing; the door may be harder to latch

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel of debris and residue
• Warm and relax the new gasket; start at the top center and press evenly into the channel without stretching
• Close the door for several hours to help the seal set; run a test cycle and check for leaks

This electronic control board kit is the appliance's central controller, coordinating inputs and powering key components. Replacing a failed board restores proper operation, responsive controls, and reliable cycle management. What it does:

• Manages timing and power to motors, valves, heaters, fans, and other loads
• Interprets sensor and user-interface signals to start, run, and end cycles correctly
• Common failure signs: dead or unresponsive controls, cycles that won't start/finish, repeated error codes, or intermittent operation
• Helps address issues caused by power surges or board damage

• 1 electronic control board (module)

• Disconnect electrical power to the appliance; turn off gas/water if applicable
• Use ESD protection and handle the board by its edges
• Photograph wiring; transfer connectors one at a time and match any jumpers/DIP-switch settings from the original board
• Restore power and perform any model-specific tests or programming per OEM instructions

Restore proper top heat to your oven with this broil element. It delivers the intense, even radiant heat needed for broiling, so foods brown and sear correctly when the original element fails or is damaged.

• Supplies high, direct heat from the top of the oven during Broil
• Common fix for no-broil or weak broiling performance
• Replace if the element is blistered, cracked, warped, or shows arcing
• Help resolve uneven browning or a tripped breaker caused by a shorted element

• Disconnect power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws and gently pull it forward
• Support and disconnect the wires; attach them to the new element and position it
• Secure the element, ensure connections are tight and clear of metal, then restore power and test

This is a replacement oven door hinge that supports and controls the swing of the oven door for smooth opening and secure closing. Restoring the hinge helps the door seal properly, improving heat retention and overall cooking performance.

• Supports the oven door's weight and movement
• Helps the door close fully to engage the gasket
• Worn hinges can cause sagging, misalignment, or a door that won't stay closed
• Also lead to heat loss and longer preheat times

• Disconnect power and allow the oven to cool completely before service
• Remove the door per your model's manual; support the door to prevent strain on the glass
• Transfer any locking clips/brackets as required by the model
• Test door operation and seal engagement after installation

This hinge receptacle mounts in the oven cabinet and provides a secure receiver for the door hinge arm. Replacing a worn receptacle restores smooth hinge engagement and helps the door close and seal correctly.

• Receives and secures the oven door hinge in the appliance frame
• Maintains proper door alignment for consistent closing and sealing
• Common symptoms: door won't close fully or stay closed; door sags or feels loose; difficulty reinstalling the door; visible wear or deformation at the receiver
• Also referred to as a hinge receiver/bracket in some catalogs

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door; hinge springs are under tension—use caution
• Remove the old receptacle from the cabinet and install the new one using existing fasteners, aligning the slot with the hinge arm
• Reinstall the door and verify smooth engagement and full closure

This dishwasher impeller assembly mounts on the circulation pump and pressurizes wash water for the spray arms. Replacing a worn or damaged impeller restores proper spray pressure, cleaning performance, and quieter operation.

• Spins with the circulation motor to pressurize wash water
• Drives flow to the spray arms for effective wash action
• Typical symptoms: weak or no spray, poor cleaning results, grinding or rattling from pump area
• Often fails from broken vanes or debris; inspect filters/chopper while open

• Disconnect power and water before servicing
• Access is typically from inside the tub: remove the lower spray arm, filter screens, and cover to reach the impeller
• Note the order of parts and transfer any reusable hardware; replace worn O-rings/seals as needed
• Do not overtighten plastic parts; verify the impeller spins freely before reassembly and testing

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

This light socket replaces a worn or heat-damaged lamp holder so your appliance light works reliably again. Its straight-connector design fits applications with in-line wiring, ensuring a secure electrical connection to the interior light bulb.

• Holds the light bulb and supplies power to it
• Restores interior illumination for better visibility
• Straight terminal orientation for housings requiring inline wiring clearance
• Typical signs of failure: light stays off with a good bulb, flickers, or shows heat damage at the socket

• Disconnect power at the breaker or unplug before servicing; allow the area to cool completely
• Remove any lens/cover; transfer wires one at a time to maintain correct connections
• Secure the socket with existing bracket/fasteners; do not overtighten
• Test light operation before reassembly and confirm the door switch activates the light

Lower wash arm redirects pressurized water across the dishwasher's lower rack to rinse and remove food and residue, restoring intended wash coverage and improving cleaning performance. What it does:

• Directs jets of water through multiple spray holes to rinse dishes on the lower rack.
• Helps remove stuck-on food, film and spotting on plates, bowls and cookware.
• Replaces cracked, clogged or broken lower spray arms that can cause poor cleaning or leftover residue.
• Works with the dishwasher's pump flow to maintain proper spray pattern across the lower rack.

• Refer to your model's parts diagram and instructions; the arm commonly snaps or threads onto the lower spray arm mount and procedures vary by model.
• Always disconnect power to the dishwasher before servicing; follow basic safety precautions.
• Clean the filter and any debris from spray holes before installing to avoid re-clogging.
• Inspect the mounting clip or retaining nut when removing the old arm and replace if damaged.

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.