Jenn-Air Dishwasher Parts

This door hinge secures and guides a refrigerator door so it opens and closes smoothly, restoring proper door alignment and seal. Designed as a direct replacement where the hinge is worn, bent, or broken. What it does:

• Supports and pivots the appliance door for proper operation and alignment
• Maintains correct door gap to help preserve the cabinet seal and cooling efficiency
• Replaces worn, bent, or damaged hinge hardware that causes sagging or misalignment
• Compatible with models that list this OEM hinge part number

• Install on a stable, unloaded door; have a helper support the door during removal and installation
• Power off and unplug the appliance before starting any repairs to avoid injury
• Reuse existing fasteners only if undamaged; replace fasteners if stripped or bent
• Check door strike and gasket condition

The Dishwasher Adapter is an OEM part for Whirlpool dishwashers. It serves as a connector, allowing various components of the dishwasher to interface correctly and ensuring proper water flow and pressure throughout the appliance.

Cracks, wear, or damage to the adapter can cause significant issues with the dishwasher's performance.

Symptoms of a bad Dishwasher Adapter include:

• Leaks under or around the dishwasher
• Poor water pressure during cycles
• The dishwasher failing to fill or drain correctly
• Visible cracks or damage to the adapter

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Right Hand Dishrack Support is an OEM replacement part for Whirlpool dishwashers. Located on the right interior side wall of the dishwasher tub, this support stabilizes the upper dishrack during the wash cycle. It features an angled plastic slab with ribs for secure placement of the dishrack tabs. 

Causes of a bad dishrack support can include cracks or breaks in the plastic from repeated impact of dishes against it over time, or cracks allowing moisture to enter and cause warping.

Symptoms of a bad dishrack support include:

• Squeaking or rattling sounds from the right side of the dishrack
• Loose or unstable fit of the upper dishrack  
• Dishes or utensils falling from the rack during spinning
• Visible cracks, breaks, or deformations in the plastic support

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, Amana, and some Kenmore and Maytag models.

The Dishwasher Door Spring is an OEM replacement part for Whirlpool dishwashers. It helps with smooth opening and closing by providing a well-balanced counterforce. 

Causes can involve coils weakening from repeated engagements over time. Metal fatigue diminishes recoil capabilities as well reducing assistive power.

Symptoms of a problematic spring include:

• Sagging or loosely fitting doors
• Difficulty fully opening or closing door
• Noises occurring from unbalanced movement

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore dishwashers.

Dishwasher door balance spring. Also check the door balance link kit 8194001.

This dishwasher dispenser assembly stores detergent and rinse aid, releasing them at the correct time in the cycle for consistent cleaning and drying performance. Replacing a damaged or leaking dispenser restores reliable detergent release and helps prevent rinse aid messes.

• Holds detergent and rinse aid and seals to the inner door
• Opens the detergent cup when signaled by the control during the wash
• Meters rinse aid into the final rinse to improve drying results
• Common symptoms: dispenser door won't open, detergent tablet left in cup, rinse aid leaks/empties quickly, door won't latch, poor cleaning from no detergent release

• Disconnect power to the dishwasher before servicing
• Remove the inner door panel to access the dispenser
• Unplug the harness, release the locking tabs, and seat the new dispenser evenly to avoid leaks
• Reconnect wiring, reinstall the panel, and run a quick cycle to check for leaks

The Door Spring is an OEM part for Whirlpool dishwashers. This part allows the smooth and controlled operation of the dishwasher door. The spring helps balance the weight of the door, allowing it to open and close effortlessly without slamming shut.

Causes of a bad door spring can include wear and tear from repeated use, corrosion or rust, and breakage due to excessive force or mishandling.

Symptoms of a bad door spring include:

• The dishwasher door dropping quickly or not staying open
• Difficulty in opening or closing the door
• Unusual noises when moving the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Shaft seal included.

Color: gray. Measures about 3 inches high by 2-1/2 inches deep.

This left-hand dishrack support mounts to the rack/rail assembly to hold the rack level and guide it in and out. Replacing a worn support restores smooth rack travel and proper alignment to prevent binding, sagging, or derailment.

• Supports the dishrack on the left side and keeps it level
• Helps the rack slide smoothly without catching or rubbing
• Replaces a cracked, warped, or missing support
• Common symptoms: rack falls off track, binds when sliding, sits unevenly, or makes scraping noises

• Disconnect power and turn off water before servicing
• Pull the rack forward, remove it from the rails, and release the old support's locking tabs/fasteners
• Snap or fasten the new support in the same orientation; reinstall the rack and check for smooth travel

This drive belt links the dishwasher's motor to the pump so the machine can circulate wash water and drain properly. Replacing a worn or broken belt restores wash action and helps eliminate slipping or squealing during cycles.

• Transfers motor power to the pump for water circulation and draining
• Common fix for no wash action or poor cleaning
• Can address squealing/chirping noises or a burning rubber smell
• Replaces belts that are cracked, frayed, stretched, or glazed

• Disconnect power and turn off the water supply before servicing
• Remove the lower access/toe panel to reach the motor and pump area
• Note belt routing; rotate the old belt off the pulleys and install the new belt the same way
• Check pulley alignment and hand-rotate to seat the belt before running a test cycle

This genuine replacement part is a control board for Whirlpool dishwashers. The control board is the main circuit board that controls the dishwasher's main functions. If the dishwasher is no longer turning on, or is not draining properly, it might be time for a new control board. Luckily, replacing a control board is an easy process.First, remove the outer door panel of the dishwasher by unthreading the mounting screws. Lift the control panel up and disconnect the wire touchpad harness from the control board. Then use a flathead screwdriver to release the locking tab and slide the control board housing to the left to detach. Remove the wire covers. Once removed, take note of the orientation of the wire connectors and disconnect them from the old board. Install the new control board by reconnecting the wire connectors to the appropriate terminals. Align the wire covers and pop them into place. Insert the control board housing tabs into the slots of the mounting bracket and slide the housing to the right to secure. Reinstall the control panel by attaching the control pad wire harness to the new board. Align the panel and rethread the mounting screws to secure. This replacement control board is compatible with Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Sears, and Kenmore brand dishwashers.

The Pump Filter is an OEM part for Whirlpool dishwashers. This filter traps debris and prevents it from entering the pump, thereby protecting the pump and ensuring the efficient operation of the dishwasher.

Causes of a bad pump filter can include clogging due to food particles and debris, wear and tear over time, or physical damage from sharp objects or improper cleaning.

Symptoms of a bad pump filter include:

• Poor drainage or standing water in the dishwasher
• Unusual noises during the wash cycle
• Reduced cleaning performance
• Frequent clogging or blockages

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Gasket for upper wheel.

The Adjuster Axle is an OEM part for Whirlpool dishwashers. It plays a crucial role in the height adjustment mechanism of the upper rack, allowing users to customize the rack's position to accommodate different dish sizes. This axle ensures that the adjustment is smooth and stable, providing flexibility in the dishwasher's loading capacity.

You should replace the adjuster axle if it becomes worn out or damaged. Causes of a bad adjuster axle can include wear from frequent adjustments, breakage from overloading the rack, or damage from mishandling.

Symptoms of a bad adjuster axle include:

• Difficulty in adjusting the height of the upper rack
• The rack not staying in the desired position
• Unusual movement or instability of the rack
• The adjuster mechanism not functioning properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Tine Row Holder is an OEM part for Whirlpool dishwashers. It is responsible for securing the tines in the dishwasher's rack, keeping them in place to hold dishes, glasses, and utensils securely during the wash cycle.

Over time, the tine row holder can become damaged due to normal wear and tear, repeated loading and unloading of dishes, or accidental mishandling.

Symptoms of a bad tine row holder include:

• Tines that are loose or fall out of place
• Difficulty in loading dishes securely
• Uneven or inadequate cleaning due to improperly spaced items

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Dishrack Stop is an OEM part for Whirlpool dishwashers. This part prevents the upper dishrack from being pulled out too far, acting as a safety stop to keep the rack securely in place. One stop per package. Located at the end of the rails that hold the upper rack.

Causes of needing to replace the Dishrack Stop can range from it breaking or becoming dislodged due to excessive force or mishandling, to general wear and tear over time.

Symptoms of a bad or missing Dishrack Stop include:

• The ability to pull the dishrack completely out of the dishwasher tub
• The dishrack becoming dislodged or falling out during operation
• Potential damage to the dishwasher interior or the dishrack itself

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.