Jenn-Air Range / Cooktop / Oven Parts

The Switch, Infinite (RF) is an OEM replacement part for Whirlpool ranges. This switch controls the heat level of the right-front burner on the cooktop, providing the user with the ability to adjust the burner to the desired temperature setting. It works by regulating the electrical current sent to the burner.

Signs of a bad infinite switch include:

• The burner not heating or being stuck on high heat  
• Difficulty adjusting the temperature setting  
• The burner failing to turn on or off  

Common causes of failure include wear from frequent use, electrical surges damaging the internal components, or physical damage from improper handling. 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This fan motor powers the cooling fan that moves air through your unit. Replacing a worn or noisy motor restores proper airflow to help maintain stable temperatures and reliable performance. What it does:

• Drives the fan blade to circulate air for cooling and temperature control
• Helps prevent component overheating caused by weak or stalled airflow
• Fixes: fan not running or starting intermittently
• Fixes: loud humming, grinding, or rattling from the fan area
• Fixes: longer run times or warm spots due to poor airflow

• Includes: 1 fan motor

• Disconnect power before servicing; allow moving parts to stop
• Note wire positions and motor orientation; take a photo for reference
• Transfer the existing fan blade and mounting hardware as needed
• After install, ensure the fan spins freely and no wiring contacts moving parts before restoring power

Jenn-Air cooktop surface burner knob. Color: Black. This knob measures about 2 inches in diameter.

This oven door hinge is a replacement for many models of ovens. Oven doors will have two hinges. If there is a problem with one or both of the hinges, it means that the door will not open and close properly. It might not stay closed, or it could be difficult to open. This would make it impossible to use the oven, and the hinge should be replaced as soon as possible.An oven door hinge could become damaged for a host of reasons. When the door is open, too much pressure could be placed on the hinge, which could cause it to break. It could become corroded over time, or the spring might wear down. When there are issues, the owner will want to replace the hinge to ensure the door stays closed. Owners should always make sure the oven is off and not powered before beginning work.The oven door hinge will work with certain models of ovens from Whirlpool, Maytag, Amana, Jenn-Air, Norge, Crosley, and Magic Chef. This is a genuine OEM replacement part, and it is sold individually. If both of the hinges need to be replaced, the owner will need to buy two.

1800 watt

This 8-inch coil surface element restores reliable heating on the large burner of electric ranges and cooktops. Its 2350-watt design provides steady, even heat for boiling, frying, and everyday cooking.

• Converts electrical power into heat for the large cooktop position
• Common failure symptoms: no heat, uneven heating, only part of the coil glowing, visible breaks or blisters, or failed continuity
• Plug-in coil style for receptacle-type burner sockets
• If no heat persists after replacement, also inspect the element receptacle and the burner switch

• Disconnect power to the range/cooktop and allow the element to cool completely
• Lift the old element and pull straight out from the receptacle
• Align the new element's terminals with the receptacle, push in firmly until fully seated, and set it into the support/drip bowl
• Restore power and test the burner

This surface heating element restores dependable heat on your electric range or cooktop. Replace a failed top burner to regain consistent boiling and simmering performance when one position stops heating, heats unevenly, or cycles unpredictably.

• Converts electrical power into heat for cookware on the cooktop
• Replaces a burned-out/open surface burner to restore normal operation
• Helps fix: no heat, intermittent heat, or uneven heating at a burner position
• Matches the original footprint and connections for proper fit and function

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the cooktop to cool completely; wear appropriate hand and eye protection
• Access the element per your service manual; note wire locations and transfer any mounting clips/brackets from the old part if present
• Seat terminals fully and secure the element before reassembly; test on low and high settings

This door latch keeps the door securely closed and engages the door switch/interlock so the appliance operates as designed. Replacing a worn or broken latch helps resolve door-related errors and restores reliable, safe operation.

• Secures the door against the strike for proper closure and alignment
• Actuates the door switch/interlock so controls recognize a closed door
• Helps prevent operation when the door is open or not fully latched
• Common symptoms: door won't latch or stay closed; unit won't start or shows a "door/open-close" message; broken or loose latch hook

• Disconnect power before servicing; use proper PPE and beware of sharp edges
• Access the latch through the door panel/trim as applicable; use non-marring tools to avoid damage
• Transfer any reusable clips/springs from the old latch to the new part
• After installation, verify smooth door closure and that the control detects the door as closed

The Convection Fan is an OEM part for Whirlpool wall ovens and ranges. It circulates hot air inside the oven cavity, facilitating even heat distribution during the cooking and baking cycles. The convection fan enhances cooking performance through fast, forced air movement.

Causes of a bad convection fan include a failed motor, worn-out blades, or blockages that disrupt airflow.  

Symptoms of a bad convection fan include:

• Incomplete or uneven cooking even at higher temperatures
• Longer than normal cook times 
• Loud buzzing or grinding noises from the fan motor area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This oven door hinge supports the door and controls its movement. Replacing a worn hinge restores smooth opening and closing and helps the door seal properly against the gasket for accurate temperatures and safer operation.

• Supports and pivots the oven door during opening and closing
• Provides closing force to help the door seal against the gasket
• Helps maintain correct door alignment
• Common symptoms of a worn hinge: door won't close fully or sits uneven, drops/slams or won't stay partially open, heat loss or long preheat, squeaking

• Disconnect electrical power; for gas ranges, also shut off the gas supply. Allow the oven to cool completely
• Support the door; hinges are spring-loaded—use caution when releasing/engaging hinge locks if equipped
• Transfer any original mounting screws/brackets as needed
• For best results, replace both door hinges together to maintain even alignment

This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.

• Creates a fixed, insulated junction between external supply wires and internal appliance wiring
• Maintains tight screw-lug connections to minimize resistance and heat buildup
• Helps ensure steady power delivery to controls, motors, and heaters
• Common indicators of failure: melted/discolored block, burning odor, visible arcing, loose or stripped terminals, intermittent or no power

• Disconnect power at the breaker and verify zero voltage before servicing
• Photograph/label wire positions; transfer one lead at a time to the new block
• Tighten terminal screws firmly; do not overtighten into the insulator
• Inspect wire ends/ring terminals and strain relief; replace any heat-damaged components per the service information

This brass seal is used on range and cooktop tubing connections to create a tight, leak-resistant joint. Replace a deformed or worn seal whenever the line is serviced so the burner system operates safely. What it does:

• Forms a tight seal in a compression-style fitting between the tube and mating connector
• Helps prevent gas odors or hissing at the joint
• Can improve ignition and flame stability when a leaking connection is corrected
• Intended to be replaced when the connection is disassembled or the old seal is crushed/deformed

• Shut off gas supply and power before servicing; allow components to cool
• Inspect tubing and fitting surfaces; replace any nicked, bent, or out-of-round parts
• Align the tube squarely and tighten per OEM guidance—do not overtighten
• After assembly, leak-test the joint with an approved solution; if leaks persist, stop.

This oven door seal forms a heat-resistant barrier around the door opening to keep heat in and stabilize temperatures. Replacing a worn seal helps restore proper door closure, efficient heating, and consistent baking performance.

• Seals the gap between the door and oven front to prevent hot air and steam from escaping
• Helps maintain stable cavity temperature and more even cooking results
• Replace if the seal is torn, frayed, hardened, flattened, or if you notice heat escaping, longer preheat times, or temperature fluctuations

• Disconnect power or gas and allow the oven to cool completely before servicing
• Open the door, remove the old seal, and clean the channel or retainers
• Press the new seal into the existing clips/retainers without stretching; align corners evenly
• After installation, verify the door closes snugly and perform a brief preheat to help seat the seal

The Microwave Thermostat is an essential component for maintaining the optimal performance of your microwave. This genuine OEM part ensures precise temperature control, allowing your appliance to operate efficiently and safely. Designed specifically for a variety of Samsung microwave models, it guarantees a secure and seamless fit, making installation straightforward for DIY repairs. The thermostat regulates the heating process, preventing overheating and ensuring consistent cooking results every time you use your microwave. By replacing a faulty thermostat with this reliable part, you can restore your microwaveGÇÖs functionality and extend its lifespan without the need for professional service. Its durable construction ensures long-lasting performance, giving you peace of mind and contributing to the overall safety of your kitchen. Whether your microwave is experiencing temperature fluctuations or failing to heat properly, the Microwave Thermostat provides a practical and effective solution. Choose this genuine OEM part to achieve dependable results and enjoy a consistently efficient microwave experience.

Color: black. It measures about 2 inches in diameter.

This Oven Bottom forms the floor of a gas oven cavity. Positioned above the bake burner, it shields the burner/igniter from spills while providing a smooth, removable surface that helps direct heat and is easier to clean.

• Covers and protects the bake burner and igniter assembly
• Helps channel heat and airflow across the oven cavity
• Catches drips and debris; removes for periodic cleaning
• Typical failure signs: warped or rusted panel, flaking finish, burnt-through spots, or persistent smoke from baked-on spills

• Allow the oven to cool completely; wear cut-resistant gloves—edges may be sharp
• Disconnect power and turn off gas supply before servicing
• Remove racks; release rear screws or tabs per your model, lift and slide the old panel out; seat the new panel under the front lip and secure
• Restore power and gas, then verify proper fit and clearance