Jenn-Air Range / Cooktop / Oven Parts

This is a replacement oven door hinge that supports and controls the swing of the oven door for smooth opening and secure closing. Restoring the hinge helps the door seal properly, improving heat retention and overall cooking performance.

• Supports the oven door's weight and movement
• Helps the door close fully to engage the gasket
• Worn hinges can cause sagging, misalignment, or a door that won't stay closed
• Also lead to heat loss and longer preheat times

• Disconnect power and allow the oven to cool completely before service
• Remove the door per your model's manual; support the door to prevent strain on the glass
• Transfer any locking clips/brackets as required by the model
• Test door operation and seal engagement after installation

This bake element restores consistent bottom heat in your electric oven so it can preheat quickly and bake evenly. Replace a burned-out element to fix no-heat in Bake, long preheat times, and uneven results.

• Provides the primary heat source during the Bake cycle
• Helps the oven reach and maintain the set temperature for even cooking
• Common symptoms: no heat in Bake, slow preheating, won't maintain temperature, element doesn't glow or shows visible damage
• Direct-fit replacement per OEM design

• Disconnect power at the breaker or unplug the range before servicing
• Remove oven racks; take out element mounting screws and carefully pull the element forward to access wiring
• Note wire positions; transfer connections without pulling on the wires and secure the element
• Reassemble and run a short Bake test to confirm proper operation

This surface burner ignition switch with protective shield mounts on the gas valve stem. When you turn the knob, it closes the circuit to the spark module to ignite the burner and the shield helps protect the switch from spills. What it does:

• Triggers the spark module to create a spark when the surface burner knob is turned
• Shield helps protect the switch from moisture, grease, and heat
• Typical symptoms of a failed switch: no spark, intermittent sparking, or continuous clicking
• One switch is used per burner valve; replace only the failed switch(es)

• 1 ignition switch with protective shield

• Disconnect electrical power and shut off gas supply before servicing
• Pull the knob straight off and remove the control/manifold panel to access the switch
• Transfer wires one at a time to the new switch; align on the valve stem and position the shield correctly
• Reassemble, restore power and gas, and verify proper spark at each burner

This is an electronic clock control board that is made for use with ovens and microwave/oven combination appliances. It is located at the back middle of the range and includes a small display window. The control panel is used to manage the oven functions like baking and broiling. It also includes a clock to show the time of day.If the oven cannot be changed from bake to broil, it may indicate the part is no longer working. A test of the heating elements can determine whether this is the case. Before starting the replacement process, make sure the range is not plugged into the wall and the oven and cooktop are both cool. Open the oven door to access the screws that hold the control board. Unclip the ribbon connection before removing the part. Reverse the process to install the new part.The electronic clock control board is sold as a single part. It is an authentic OEM replacement part that is compatible with wall ovens and microwave/oven combos from Jenn Air.

This hinge receptacle mounts in the oven cabinet and provides a secure receiver for the door hinge arm. Replacing a worn receptacle restores smooth hinge engagement and helps the door close and seal correctly.

• Receives and secures the oven door hinge in the appliance frame
• Maintains proper door alignment for consistent closing and sealing
• Common symptoms: door won't close fully or stay closed; door sags or feels loose; difficulty reinstalling the door; visible wear or deformation at the receiver
• Also referred to as a hinge receiver/bracket in some catalogs

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door; hinge springs are under tension—use caution
• Remove the old receptacle from the cabinet and install the new one using existing fasteners, aligning the slot with the hinge arm
• Reinstall the door and verify smooth engagement and full closure

This convection fan blade mounts to the fan motor and circulates hot air during convection cycles. Replacing a bent or damaged blade restores proper airflow, promoting more even temperatures and consistent baking and roasting performance.

• Mounts on the convection motor shaft to drive airflow through the oven cavity
• Helps maintain uniform temperatures for consistent convection baking/roasting
• Typical failure signs: rattling or scraping noises, visible wobble or damaged fins, weak airflow, or the fan not spinning freely
• A worn blade can contribute to uneven results in convection mode

• Disconnect power and allow the appliance to cool completely before servicing
• Access the blade behind the interior fan cover or rear panel (varies by model); note blade orientation and any spacers/washers for reassembly
• Handle sharp edges; avoid bending fins and ensure the blade spins freely without rubbing before restoring power
• For microwave/OTR convection units, high-voltage components are present.

This dual infinite switch controls power to a dual-size surface element on your range or cooktop, restoring smooth, accurate heat adjustment. Replace a failed switch to regain proper temperature control and dual-ring operation.

• Regulates cycling power to the inner and outer circuits of a dual surface element
• Provides variable heat levels from low to high
• Common symptoms of a failed switch: element won't heat, only heats on high, can't adjust temperature, element won't shut off, inner or outer ring won't activate
• Restores reliable response when selecting single-ring or dual-ring settings

• Disconnect power at the breaker before servicing
• Remove the control/console panel to access the switch
• Photograph/label wiring and transfer leads one at a time to matching terminal markings on the new switch
• Reassemble, reinstall the knob, and test both single-ring and dual-ring operations

This broil element provides the intense top heat your oven uses for broiling. Replace a failed or damaged element to restore consistent broiler performance and proper browning when broiling meats and other foods.

• Supplies high, direct radiant heat from the top of the oven during broil cycles
• Restores proper broiling performance for browning and searing
• Replaces elements with open circuits, blisters, cracks, or shorts
• Common symptoms include: broiler won't heat, weak or uneven broiling, visible damage, or the breaker trips when broil is turned on

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and disconnect wires; support wires so they don't slip back into the rear cavity
• Attach wires to the new element and secure with existing screws; avoid bending the element or overtightening
• Restore power and test the broil function

This adhesive-backed foam tape seals small gaps and cushions mating parts inside your appliance. Replacing worn or missing foam helps reduce noise and vibration while preventing air leaks and condensation that can lead to performance issues.

• Seals joints and gaps to help maintain proper airflow and temperature control
• Cushions panels and components to reduce rattles, buzzing, and vibration
• Helps prevent moisture intrusion that can cause condensation or frost
• Restores secure fit where original foam has compressed, torn, or fallen off

• Disconnect power (and water supply if applicable) before starting
• Remove all old foam/adhesive and clean surfaces; allow to dry fully
• Measure, cut to length, peel backing, and apply without stretching the tape
• Press firmly along the length for good adhesion; keep clear of moving parts and vents

This oven door hinge supports and guides the door through its range of motion so it opens smoothly and seals tightly when closed. Replacing a fatigued hinge restores proper door alignment and consistent oven performance. What it does:

• Provides spring-assisted tension to control door opening and closing
• Helps the door seal evenly against the gasket to retain heat
• Maintains correct stop positions to prevent slamming or over-travel
• Common symptoms: door won't close fully or pops open, drops/slams, sits crooked, heat escaping/long preheat

• One door hinge assembly

• Disconnect power at the breaker; allow the oven to cool completely before servicing.
• Remove the door per your model's procedure (often open to the broil stop, engage hinge locks, then lift off).
• Use hinge locks/pins to control spring tension and prevent snap-back during removal/installation.
• Support the door to avoid damage; many replace both hinges together to keep tension balanced.

This replacement jack mounts inside the oven cavity and provides the receptacle for the food temperature probe. It restores a dependable connection so the control can monitor internal food temperature and operate probe-cook features as intended.

• Provides the in-oven receptacle for the food/meat temperature probe
• Carries the probe's signal to the control during probe-cook cycles
• Helps resolve issues where the control does not recognize a probe or the probe feature won't run
• Replaces a jack that is damaged, corroded, or loose

• Disconnect power at the breaker and allow the oven to cool completely
• Access from inside the oven; remove the mounting screw(s) and carefully pull the jack to reach the wire harness
• Transfer/connect the harness and seat any gasket or insulation to maintain the oven cavity seal
• Do not overtighten fasteners; avoid pinching or damaging wires and insulation

This plug-in coil cartridge restores reliable surface heating on compatible modular cooktops. Replace a worn or damaged module to regain consistent burner performance and maintain a matching black finish. What it does:

• Provides electric surface heat via a self-contained coil cartridge that plugs into the cooktop receptacle
• Helps resolve issues like a surface burner not heating or heating intermittently
• Addresses problems from visible damage or burned/loose cartridge terminals
• Preserves proper fit and appearance for black-finish cooktops

• 1 coil cartridge assembly

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift out the old cartridge; inspect the cooktop receptacle for heat damage before installing
• Align guides and terminals; seat the cartridge fully without forcing the connection
• Restore power and test burners at low/medium settings first

This is a Whirlpool range control panel assembly. It houses the display, user interface buttons, and has space for temperature control knobs. With extended use, the buttons on a control panel may wear out or stop responding to user input.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the old control panel in place. Remove the screws from each side of the old control panel to disconnect it, then carefully remove any boards or other components installed within the panel. Once it has been completely removed, the new control panel can be installed in its place.This is a genuine OEM part compatible with ranges manufactured by Jenn-Air, but may also work with other Whirlpool brands, including Maytag, KitchenAid, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.

This door latch secures the appliance door and signals the control that it's safely closed. Replacing a worn or broken latch restores reliable door closure and proper cycle operation. What it does:

• Holds the door closed and aligned during use
• Engages the door strike to complete the door/lock switch circuit
• Resolve issues such as: door won't latch or pops open; cycles won't start; intermittent "door open" messages; needing to press/hold the door to run

• One door latch

• Disconnect power before servicing
• Access is typically from the door/front panel; note screw locations and latch orientation
• Transfer any mounting hardware from the original latch if needed
• After installation, verify smooth latch engagement with the strike and run a test cycle

The Screw is an OEM part for Whirlpool microwaves. It is responsible for securing various parts of the microwave together. This screw ensures a tight and secure fit for parts and helps maintain the structural integrity of the microwave, preventing any loose or rattling parts.

A bad microwave screw can occur due to wear and tear, accidental damage, or misplacement during maintenance or repairs. If you notice symptoms such as loose or wobbly components, difficulty in opening or closing the microwave door, or abnormal noises while the microwave is in use, it may be time to replace this part.

Symptoms of a bad microwave screw include:

• Loose or wobbly components
• Difficulty in opening or closing the microwave door
• Abnormal noises during operation

Restore your Whirlpool microwave by replacing the faulty or missing microwave screw with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This oven door gasket restores a tight seal between the door and the oven front frame. A proper seal reduces heat loss, supports accurate temperatures, and helps food bake and roast more evenly.

• Creates a heat-resistant seal at the door-to-cavity opening to contain heat and airflow
• Helps maintain stable oven temperatures and normal preheat times
• Replace if the seal is torn, frayed, brittle, flattened, burned, or leaking
• Helps resolve heat escaping around the door, uneven baking, or longer cook times

• Disconnect power; for gas appliances, also shut off gas. Allow the oven to cool completely
• Remove the old gasket by releasing end retainers or pulling it from the channel; clean the groove
• Install the new gasket without stretching; seat it evenly around the perimeter with corners aligned
• Close the door and check for uniform contact all around; adjust as needed per your model instructions