Kenmore / Sears Dishwasher Parts

The Drain Pump is an OEM part for Whirlpool dishwashers. It is responsible for removing wastewater from the dishwasher tub during the drain cycle, ensuring that the dishwasher operates efficiently and effectively.

Causes of a bad drain pump can include clogging from food particles and debris, damage to the pump impeller, or electrical failures within the pump motor. Over time, regular use can lead to wear and tear that affects the pump's performance.

Symptoms of a bad drain pump include:

• Water not draining from the dishwasher
• Standing water at the bottom of the dishwasher after a cycle
• Unusual noises during the drain cycle
• Error codes related to drainage issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool dishwashers. This single clip works to secure the lower dishrack in its correct position during the wash cycle. 

Symptoms of a bad dishrack stop clip can include: 

• The lower dishrack rattling or moving excessively during spinning
• Dishes and utensils falling to the bottom of the tub and not getting clean
• Visible wear on the clip material

Causes can be normal wear from securing the dishrack cycle after cycle. Improper loading may also damage the clip over time.

This OEM Whirlpool part replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers. 

This replacement sealing gasket restores a tight, leak-resistant barrier between mating components in your appliance. Replacing a worn seal helps prevent leaks and moisture escape to keep performance stable and reliable.

• Maintains a watertight/airtight seal between connected parts
• Helps resolve leaks, drips, and moisture pooling inside or beneath the unit
• Addresses issues caused by flattened, cracked, or hardened seals
• Supports proper operation by preserving pressure and flow at the joint

• Disconnect power and, if applicable, shut off water before servicing
• Remove the related cover/assembly to access the old seal; note its orientation
• Clean the groove/mating surfaces; install the new seal evenly without stretching
• Reassemble and run a short test to check for leaks

The Water Inlet Valve is an OEM part for Whirlpool dishwashers. It regulates the flow of water into the machine. This valve opens and closes to allow the right amount of water in during various cycles, ensuring dishes are cleaned effectively without wasting water. 

Over time, the water inlet valve can fail due to mineral buildup from hard water, wear and tear from frequent use, or mechanical failure of the valve components. A malfunctioning valve can lead to problems such as insufficient water entering the dishwasher, leading to poorly cleaned dishes, or leaking, which can cause water damage over time.

Symptoms of a bad Water Inlet Valve include:

• Dishwasher not filling with water
• Water filling too slowly or overfilling
• Unusual noises during the fill cycle
• Leaks around the dishwasher

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Gasket and Strike Kit is an OEM part for Whirlpool dishwashers, designed to ensure a tight and leak-proof seal around the dishwasher door. This kit includes a door gasket and a door strike, both crucial components in preventing water from leaking out during the wash cycle. 

Causes of a bad Gasket and Strike Kit can include normal wear and tear from regular use, leading to a loss of elasticity in the gasket.

Symptoms of a bad Gasket and Strike Kit include:

• Water leaking from around the dishwasher door.
• Difficulty closing the dishwasher door or ensuring it stays latched during operation.
• Visible signs of wear, such as cracks or hardening on the gasket, or bending or damage to the strike.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Dishwasher Food Chopper is an OEM part for Whirlpool dishwashers. It's designed to break down food particles that are washed off dishes during the cleaning cycle. This prevents large debris from clogging the dishwasher's drain and ensures that water remains clean throughout the cycle, enhancing the machine's cleaning efficiency. 

A malfunctioning or worn-out food chopper can lead to several problems, such as poor cleaning results due to food particles being redeposited on dishes, or even clogs that can strain the dishwasher's pump and filters. 

Symptoms of a bad Dishwasher Food Chopper include:

• Dishes coming out with food particles still on them
• The dishwasher making unusual noises indicating a struggle or blockage
• Water not draining properly, suggesting a possible clog

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Latch is an OEM part for Frigidaire dishwashers. It secures the dishwasher door during operation, ensuring a watertight seal that prevents leaks and allows the dishwasher to run efficiently.

Causes of a bad latch can include wear and tear from regular use, damage from slamming the door, or misalignment over time. Additionally, the latch mechanism can wear out, affecting its ability to hold the door shut.

Symptoms of a bad latch include:

• Dishwasher door not closing or latching properly
• Mid-cycle interruptions due to door opening
• Leaks around the dishwasher door
• The dishwasher not starting because the door is not securely latched

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Detergent Dispenser is an OEM part for Whirlpool dishwashers. It plays a crucial role in the dishwasher's operation by dispensing detergent and rinse aid at the precise moments during the wash cycle. This ensures dishes are thoroughly cleaned and dried without residue.

Causes of dispenser failure can range from mechanical issues such as a faulty spring or latch, blockages within the dispenser itself, or electronic problems affecting the timing and release of detergent.

Symptoms of a bad Detergent Dispenser include:

• Failure to dispense detergent properly, leading to dishes not being cleaned effectively.
• Rinse aid leakage, which can result in streaky and spotty dishes.
• The dispenser door sticking or failing to open during the wash cycle.
• Unusual noises coming from the dispenser mechanism.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Tine Row Pivot is an OEM replacement part for Whirlpool dishwashers. This component is an integral part of the upper rack assembly, allowing the tine rows to fold down or pivot inward to accommodate taller items or create additional space within the rack.

Symptoms of a faulty tine row pivot may include:

• Tine rows not folding or pivoting smoothly
• Difficulty adjusting the tine rows to the desired position
• Tine rows becoming stuck or jammed in an open or closed position

Causes of needing to replace the tine row pivot can include normal wear and tear over time, physical damage from mishandling or impact, or issues with the pivot mechanism becoming corroded or obstructed.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models. 

The Tub Corner Baffle is an OEM part for GE dishwashers. This rubber component is placed in the corners of the dishwasher tub to prevent water from leaking out during the wash cycle. It acts as a barrier, directing water back into the tub and ensuring efficient operation. This is the left side. For the right side, use WD8X227.

Causes of a bad part can include prolonged exposure to detergents and hot water, leading to material breakdown, or physical damage from loading and unloading dishes. 

Symptoms of a bad Tub Corner Baffle include:

• Visible signs of wear or damage
• Water leakage from the corners of the dishwasher door
• Unusual noises during operation

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Tub Corner Baffle is an OEM part for GE dishwashers. It is strategically placed at the corners of the dishwasher tub to prevent water from leaking out during operation.  For the left side use WD8X228. Color: Black.

Symptoms of a bad Tub Corner Baffle include:

• Water leaking from the corners of the dishwasher door.
• Pools of water forming near the dishwasher after operation.
• Decreased cleaning performance due to water escaping the wash cycle area.

Causes of a bad tub corner baffle can include wear and tear from regular use, improper installation leading to gaps or looseness, and degradation of the material over time due to exposure to detergents and high temperatures.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This support is a refrigerator mounting bracket that stabilizes internal components and keeps assemblies aligned for reliable operation. It replaces worn or broken supports to help reduce rattling and improper panel fit. What it does

• Secures and aligns internal cabinet or component panels to prevent shifting during normal use
• Helps maintain proper spacing for doors, panels, or internal assemblies
• Reduces vibration or rattling caused by loose or damaged supports
• Commonly replaced when a support is cracked, broken, or no longer holds mating parts securely

• High-level replacement: typically accessible from inside the cabinet or behind a trim panel; exact steps depend on model
• Use proper tools and retain all fasteners during removal for reinstallation
• Disconnect power before servicing any electrical components or removing panels near wiring

This splash shield kit is an OEM replacement part that prevents water from spraying beyond the door seal in Frigidaire dishwashers. The kit measures 1.5 inches in length, 0.5 inches in width, and 1.7 inches in height.  This kit is located on the front lower corners of the dishwasher tub. If your dishwasher is leaking due to a damaged or worn-out splash shield, the kit provides a reliable replacement.

Symptoms of a bad splash shield kit include:

• Stains or mineral deposits on surrounding cabinetry   
• Puddles or drips developing outside the dishwasher tub 
• Reduced cleaning ability due to unredirected spray patterns
• Damage, cracks or missing sections of splash shielding 

Causes can be normal wear from extended use breaking down barriers over time. Proper shield alignment is needed to effectively direct spray inside the tub.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Water Inlet Valve is an OEM replacement part for Whirlpool dishwashers. The water inlet valve is responsible for regulating the flow of water into the dishwasher. It is connected to the main water supply and opens and closes as needed to allow water to enter the appliance at the appropriate time and in the correct quantity. 

Causes of a bad Water Inlet Valve can include mineral deposits that clog the valve, a failure in the valve's solenoid, or wear and tear over time that affects the valve's ability to open and close properly.

Symptoms of a bad Water Inlet Valve include:

• Dishwasher not filling with water
• Water filling too slowly or too quickly
• Water leaking from the dishwasher
• Unusual noises during the fill cycle

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: The white plug connector can be disconnected to allow for connection of the dishwasher wiring if needed.

The Water Inlet Valve is an OEM replacement part for Frigidaire washing machines. It is a component responsible for controlling the flow of water into the washing machine tub during the wash and rinse cycles.

Symptoms of a faulty Water Inlet Valve include:

• No water or insufficient water entering the washing machine tub
• Washing machine not filling or taking an excessive amount of time to fill
• Leaks or water dripping from the inlet valve area
• Unusual noises or vibrations during the fill cycle

Causes of a bad water inlet valve can include normal wear and tear over time, sediment buildup or blockages, electrical malfunctions, or physical damage from water pressure issues or freezing conditions.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore washing machine models.

The Dishwasher Adjuster Positioner is an OEM part for Whirlpool dishwashers. It plays a vital role in adjusting the height of the upper rack, allowing for flexible loading options and accommodating larger items when necessary.

Causes of a bad Dishwasher Adjuster Positioner can include mechanical wear and tear from regular use, stress fractures from bearing excessive weight, or damage during rack adjustment.

Symptoms of a bad Adjuster Positioner include:

• Difficulty in adjusting the height of the dishwasher rack,
• The rack becoming loose or failing to stay in the set position,
• Unusual sounds or resistance when moving the rack up or down.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.