Need Help?
Call or text
Shaft that secures front drum support rollers in your dryer. Replace if worn, scored, or damaged to restore proper drum alignment and support.
Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more
Idler pulley assembly for dryers. Mounts on the idler arm to keep the belt aligned and tensioned. Replace if pulley is worn, cracked, or squeaking.
The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more
Idler pulley maintains tension on the dryer belt. Replace if worn, cracked, or causing belt slippage. Installs between motor and drum support system.
I have an LG dryer purchased in 2007. Model: DLE9577SM. It was squeaking at start-up and rumbling a little. Not knowing what parts I would actually need, I ordered rollers with/without assemblies, tensioner pulley-only, new belt. After viewing this video a couple of times, I attacked my machine which is located in the comfort of my garage. Lots of room to spread out. Nice. This disassembly went OK however because, I suspect, my machine is 13 years old, the removal of the control panel was... Read more
Idler arm assembly mounts near the dryer drum to guide and tension the belt. Replace if the pulley is worn, cracked, or causing belt misalignment issues.
Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more
Dryer drum roller axle mounts to the rear panel and supports drum rollers. Replace if bent, worn, or wobbling. Helps eliminate noise from damaged axles.
Replaced the tension pulley assembly, drum rollers, drum roller axles, belt, and drum glides while I had the dryer disassembled. It turned out that the cause of the squeak was the tension pulley assembly, however it was easy and economical enough to replace anything that could have been the cause of the squeaking while I had the dryer apart. The parts were ordered on Thursday afternoon and delivered on Friday. I had the dryer repaired and running like new in no time. For about $100, it was... Read more
Replacement drum support roller wheel assembly for dryers. Installs on bulkhead to support and guide drum rotation. Replace when worn, cracked, or loose.
I encountered a high pitched squeal and loud rumbling. I figured the sounds were likely the rollers despite not matching other sounds on the repair videos for other dryers. The repair video for dryer rollers on AppliancePartsPros.com is of little use until Minute 2:56 because this Electrolux 517 model uses mostly Phillips head screw to fasten the front and top panels in place. You may find one latch at the top front center that holds the top and front panels in place. After unplugging the... Read more
Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.
After replacing the belt less than a year ago, when it broke again we started to think something may be going on with the idler pulley. Ordered a new belt and pulley wheel, only to have the belt break again the very next day. After a call to customer service explaining the situation, they replaced the belt and pulley wheel which were both under warranty, and suggested replacing the arm itself. We also had to replace the interlock switch. Parts arrived quickly. The repair itself took about an... Read more
Drum roller kit for dryers. Installs inside cabinet to support drum rotation. Replace when rollers are worn, cracked, or causing noise during operation.
Sprocket that connects the motor to the drum drive system in your dryer. Replace if teeth are worn, stripped, or the part is cracked or broken.
Connects the water supply line to your dryer's inlet fitting. Replacement needed when the original adapter is damaged, cracked, leaking, or missing.
Replaces a worn, damaged, or misaligned dryer motor pulley. Guides the drive belt and transfers motor power to the drum for proper rotation.
Replaced belt, pulley with a 4 grove pulley. Pulley that was on there was a 3 grove pulley, Had to cut the old one off, Press on to shaft. Replaced rear drum bearing. Bearing was locked on with a snap ring. Access to it from a removable plate on the back side of dryer. Reset belt and idler puller by removing a long back plate on the bottom rear side of the dryer. None of this was shown in your Video. Read more
Motor pulley for dryers. Mounts on the motor shaft to drive the drum belt. Replace if cracked, worn, or causing belt slippage during operation.
Flywheel component for dryer drum rotation system. Installs on motor shaft or drum mechanism. Replace if cracked, chipped, worn, or missing teeth.
Usually ships within 4 - 14 days
Belt tensioner idler arm for dryers. Mounts to the drum support frame to maintain proper belt tension. Replace if cracked, broken, or worn springs.