Kenmore / Sears Dryer Gasket & Seal

Fiberglass-reinforced door seal that restores an appliance door's airtight closure to help maintain consistent temperatures, reduce energy waste and minimize frost or moisture buildup around the door. What it does:

• Forms a continuous gasket around the door to keep cold air in and warm air out.
• Helps prevent frost buildup and uneven temperatures caused by air leaks.
• Common symptoms that indicate replacement: visible gaps, cold-air leakage, frost/ice at the door, or a door that won't seal flush.
• Fiberglass construction helps the seal retain shape for a more reliable long-term closure.

• Disconnect power to the appliance before beginning any service.
• Remove the old seal and clean the door channel; press the new seal evenly into place, checking for full contact around the perimeter.
• Some models may require partial door or liner removal—before disassembly.
• If the seal is stiff, follow OEM-recommended conditioning (allow to warm to room temperature or use manufacturer guidance) to help it seat properly.

This rubber rear drum seal fits the dryer drum opening and helps keep the drum centered while reducing air leaks and preventing lint and fabric from getting between the drum and bulkhead for quieter, more efficient drying. What it does:

• Seals the gap between the dryer drum and bulkhead to maintain proper airflow.
• Cushions the drum edge to prevent metal-on-metal contact and reduce noise.
• Worn or torn seals can cause rubbing, squeaking, banging, excess vibration, or longer dry times.
• Visible gaps, shredded rubber, or lint buildup at the drum edge are common signs the seal needs replacement.

• Disconnect electrical power (and shut off gas supply for gas dryers) before starting any repair.
• Replacement commonly requires partial or full drum removal; inspect the drum and bulkhead for additional wear while accessible.
• Wear gloves and eye protection; watch for sharp edges and pinch points during reassembly.

This replacement gasket restores a reliable seal between mating parts in your appliance. A fresh seal helps keep air, moisture, and heat where designed, supporting proper performance while reducing leaks, drafts, and rubbing noises from a worn or deformed gasket. What it does:

• Forms a tight, resilient barrier between two surfaces to prevent unwanted air or water escape
• Helps maintain proper airflow, temperature, and/or water containment as designed
• Common signs of failure: visible tears, flattening, fraying, gaps, moisture where it shouldn't be, or unusual scraping/rubbing noises
• Replace if the seal no longer sits evenly, stays in place, or shows noticeable wear

• 1 gasket

• Disconnect power; shut off water or gas supply if applicable. Allow hot components to cool.
• Wear cut-resistant gloves; internal panels and edges can be sharp.
• Access the sealing area per your model's service procedure; remove the old gasket and clean the mating surfaces.
• Seat the new gasket evenly all the way around, then reassemble and check for uniform contact.

This vinyl door seal lines the perimeter of the appliance door to help block air and moisture leaks, cushion the close, and maintain proper operation. Replace a worn seal to restore a tight, quiet, reliable door closure.

• Creates a continuous seal around the door opening to reduce leaks
• Helps contain air and moisture and dampens door vibration
• Replace if the seal is torn, cracked, flattened, or coming loose
• Symptoms include gaps or drafts at the door, noise, or visible wear

• Disconnect power; for gas appliances, also shut off the gas supply
• Remove inner door panel/trim as needed to access the seal area
• Remove the old seal and clean the mounting surface of residue
• Install the new seal without stretching; if your model uses adhesive, apply per instructions and allow proper cure time

This replacement seal restores a tight barrier between mating parts in your appliance, helping maintain proper performance. It replaces a worn or deformed factory seal that can no longer hold a reliable fit due to age, heat, or chemical exposure.

• Creates a tight barrier between components to prevent leaks or air intrusion, as designed for the assembly
• Helps maintain correct pressure/flow and overall performance
• Common signs of failure: cracks, flattening, brittleness, or residue at the joint
• Helps address moisture seepage or performance loss at the sealed connection

• Disconnect power and, if applicable, turn off water supply before servicing
• Access the sealed joint; note the original seal's orientation
• Clean and dry mating surfaces thoroughly; install the new seal evenly and squarely
• Do not use sealants or lubricants unless specified by the manufacturer; test for leaks/fit before reassembly

Replacement door gasket that seals the refrigerator/freezer door to help keep cold air in, reduce energy loss, and maintain consistent temperatures for stored food. What it does

• Forms an airtight seal around the door to prevent warm air from entering the compartment.
• Helps maintain even cooling and prevents frost or ice buildup caused by air leaks.
• Can reduce running time and energy use when the original gasket is torn, warped, or no longer seals.
• Common symptoms of a failing gasket: visible gaps, condensation or frost at the door, uneven temperatures, or increased energy use.

• Disconnect power to the appliance and remove food from affected areas before beginning work.
• Inspect the door frame for dirt or debris and clean mating surfaces before installing the new gasket.
• Align the gasket to the door and seat it fully—follow OEM alignment steps for your model; if the gasket is stiff, warm it slightly per OEM guidance to help fit.

This door gasket is the flexible sealing strip that helps keep cold air inside your refrigerator, improving temperature stability and efficiency. It replaces worn or torn seals to reduce drafts and moisture intrusion. What it does:

• Creates an airtight seal around the refrigerator door to help maintain proper internal temperature
• Helps prevent frost buildup and condensation by keeping warm, humid air out
• Reduces energy waste caused by cool-air leaks around the door
• Can fix common symptoms like warm spots near the door, excessive frost, or an overworking compressor

• High-level replacement: usually removed from the door channel and pressed into place; may require loosening door hinges for full removal on some models
• Check that the gasket sits evenly in the channel and that the door closes flush to ensure a proper seal
• Clean the door channel and mating surface before installing to ensure good adhesion and sealing

This genuine replacement door gasket seals the refrigerator door to keep cold air in and reduce energy loss. It helps maintain consistent temperatures and prevents drafts and moisture buildup around the door. What it does:

• Creates an airtight seal between the door and cabinet to preserve internal temperature
• Helps prevent frost and condensation by stopping warm, humid air from entering
• Reduces compressor run time by minimizing cold-air leakage
• Commonly replaced when the seal is torn, compressed, warped, or no longer seals fully

• One door gasket

• Clean mating surfaces and remove old gasket adhesive before installing the new gasket
• Gasket may need to be warmed and flexed for proper seating; follow OEM fitting guidance
• Check for even compression around the door; do not overtighten or force the gasket
• Disconnect power or follow safety guidelines per appliance before performing service

The Seal is an OEM replacement part for Whirlpool dryers. It creates a tight seal between the dryer door and the drum, preventing heat and moisture from escaping during the drying process. It helps maintain the proper temperature inside the dryer, allowing your clothes to dry quickly and evenly.

Symptoms of a faulty door seal include:

• Heat escaping from around the dryer door
• Excessive moisture or lint buildup
• Extended drying times

A bad door seal can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as heat escaping from around the dryer door, excessive moisture or lint buildup, or clothes taking longer to dry than usual, it may be time to replace the door seal.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This door seal is the refrigerator door gasket that helps maintain a tight seal to keep cold air in and reduce energy loss. Replacing a worn or torn gasket helps the appliance cool efficiently and protect stored food. What it does

• Forms an airtight barrier around the refrigerator door to prevent warm air from entering
• Helps maintain consistent internal temperature and efficient operation
• Reduces frost buildup and cycling caused by a leaking seal
• Commonly shows symptoms like visible cracks, tears, flattening, or a door that won't close snugly

• One refrigerator door gasket

• Inspect the door frame and strike surfaces; clean mounting channel before installing the new gasket
• Warm the gasket slightly or use recommended installation tools to ease fitting into the channel
• Check alignment and closure after installation; replace if mounting clips or retainer are damaged
• Disconnect power only if required by your model and follow all safety precautions

This rubber door seal replaces a worn or damaged washer boot gasket to help keep water inside the tub and prevent leaks. It restores a tight, flexible seal around the door opening for reliable washing performance. What it does:

• Creates a watertight barrier between the wash tub and the door to prevent leaks
• Helps contain suds and water during fill and spin cycles
• Reduces odors and mold buildup by restoring a smooth, intact sealing surface
• Typical symptom: visible tears, deformation, or water pooling around the door

• One replacement door seal/gasket

• Disconnect power and turn off water supply before starting any repairs
• Inspect mounting lip and retaining band; replace any damaged clamps or retainers as needed
• Clean the sealing surfaces and allow to dry before installing the new seal

This door seal is a flexible refrigerator gasket that helps keep the cabinet airtight to maintain proper cooling and efficiency. Replaces a worn, torn, or misshapen seal to reduce cold air loss and improve temperature stability. What it does:

• Forms an airtight seal between the refrigerator door and cabinet to help keep cold air in
• Helps prevent frost build-up and reduces the workload on the compressor
• Commonly replaced when the gasket is cracked, torn, flattened, or allowing cold air to leak
• Compatible with models that use PN W10325058

• One door seal / refrigerator door gasket

• Basic push-in or screw-in installation; follow your appliance's service manual for the correct procedure
• Inspect the door frame and fastening channel for debris before installing the new seal
• Warm the gasket with a hair dryer (low heat) or allow time for it to relax to improve fit, as needed
• Disconnect power to the appliance before any service that requires removing panels or working near electrical components