Kenmore Elite Parts

The Water Filter LT800P is an OEM part for LG refrigerators. This filter is designed to remove contaminants from the water supply, ensuring clean and fresh-tasting water and ice.

Causes of a bad water filter can include extended use beyond its recommended lifespan, exposure to high levels of contaminants, or damage to the filter itself.

Symptoms of a bad Water Filter LT800P include:

• Unpleasant taste or odor in the water or ice
• Reduced water flow from the dispenser
• Indicator light signaling the need for replacement
• Visible sediment or particles in the water

This OEM LG part is also compatible with Sears/Kenmore.

This burner restores proper flame distribution and ignition performance in your gas cooking appliance, helping you achieve steady, even heat for reliable boiling, simmering, and searing. What it does:

• Directs gas from the orifice through burner ports for an even flame pattern
• Works with the igniter/electrode to light the burner
• Helps reduce symptoms like uneven or weak flame, delayed ignition, or flame that lifts or makes popping noises
• Can address issues where the burner won't light or only lights partially due to damage or blockage

• 1 burner

• Disconnect power and shut off gas before servicing
• Access the burner per your model's service instructions; transfer any required hardware from the old part
• Ensure proper alignment with the igniter and orifice; tighten fasteners securely
• Restore gas and power, then inspect flame; check for leaks if any gas fittings were disturbed

This moisture sensor connector assembly links the dryer's sensor bars to the control to monitor fabric dryness and adjust cycle time. Replacing a damaged or loose harness restores consistent Auto Dry operation.

• Connects the moisture sensor bars to the main control for Auto Dry feedback
• Transmits the low-voltage signal used to determine when clothes are dry
• Failure may cause Auto Dry to end too soon, run too long, or deliver inconsistent results
• Typical issues include broken wires, loose/corroded terminals, or a heat-damaged plug

• Disconnect power; if gas, shut off gas supply before service
• Access the moisture sensor area at the front/lint housing
• Match routing and clips, seat terminals fully on the sensor tabs, and secure the connector
• Keep wiring clear of sharp edges and moving parts; reassemble and test a Sensor Dry cycle

The Surface Burner Switch is an OEM Replacement Part designed to control the large surface burner on your Frigidaire stove. This switch is suitable for an 8" element with a wattage range of 2136 - 2640 watts. With a capacity of 8.9-11.0 amps and 240 volts, it allows you to adjust the burner temperature by regulating the electrical current to the burner element, ensuring precise cooking temperatures.

Causes of a bad surface burner switch can include electrical faults, wear and tear from frequent use, or internal component failure. When the switch fails, it can result in the inability to control the burner temperature accurately, which may affect cooking performance.

Symptoms of a bad surface burner switch include:

• The burner not heating up or heating inconsistently
• Inability to adjust the burner temperature
• The burner remaining on high heat regardless of the setting
• Unusual sparking or electrical noises from the switch area

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Note: For the new mounting screws, order part number 5303288565. Two are needed to properly mount the new switch.

The Main PCB Assembly is an OEM replacement part for LG refrigerators. As the primary control board, it manages all refrigerator functions and features such as temperature control, frost free operation, and diagnostic fault codes.

Causes of a faulty PCB can involve spilled liquids corroding circuit pathways over time, defects in integrated computer chips, or loose connections susceptible to arcing under continuous power loads.

Symptoms include:

• Non-responsive control panels and displays
• The refrigerator failing to cool or maintain proper temps
• Abnormal sounds from the compressor and fans not engaging

Also compatible with some Kenmore models

The Dispenser Lever Retainer is an OEM part for LG refrigerators. This part secures the dispenser lever in place, this part ensures the smooth operation of the water and ice dispenser. 

Causes of a bad Dispenser Lever Retainer can include normal wear and tear from repeated use, accidental damage, or deterioration of the material over time.  

Symptoms of a bad Dispenser Lever Retainer include:

• The dispenser lever is loose or wobbly
• Difficulty in dispensing water or ice
• The lever does not return to its original position after use
• Unintended activation or difficulty in activating the dispenser

This OEM LG part is also compatible with some Kenmore models.

The Blower Wheel is an OEM part for LG dryers. This part circulates air through the dryer drum and out the exhaust vent, ensuring proper airflow for efficient drying of clothes.

Causes of a bad blower wheel can include accumulation of lint and debris, wear and tear over time, or physical damage due to foreign objects entering the blower housing.  

Symptoms of a bad blower wheel include:

• Reduced or no airflow from the exhaust vent
• Unusual noises such as rattling or squealing during the drying cycle
• Clothes taking longer to dry or remaining damp
• Overheating or frequent shutdowns of the dryer

This OEM LG part is also compatible with some Kenmore models.

This dishwasher dispenser assembly stores detergent and rinse aid, releasing them at the correct time in the cycle for consistent cleaning and drying performance. Replacing a damaged or leaking dispenser restores reliable detergent release and helps prevent rinse aid messes.

• Holds detergent and rinse aid and seals to the inner door
• Opens the detergent cup when signaled by the control during the wash
• Meters rinse aid into the final rinse to improve drying results
• Common symptoms: dispenser door won't open, detergent tablet left in cup, rinse aid leaks/empties quickly, door won't latch, poor cleaning from no detergent release

• Disconnect power to the dishwasher before servicing
• Remove the inner door panel to access the dispenser
• Unplug the harness, release the locking tabs, and seat the new dispenser evenly to avoid leaks
• Reconnect wiring, reinstall the panel, and run a quick cycle to check for leaks

The Leveling Leg is an OEM part for Whirlpool ranges. It's designed to ensure your range is perfectly balanced and stable on uneven floors. By adjusting the height of the leveling legs, you can prevent wobbling and ensure that your cooking surface is perfectly horizontal, which is critical for even cooking and baking.

Causes of a malfunctioning Leveling Leg can stem from physical impact damage, corrosion in humid conditions affecting integrity and adjustability, and wear over time, particularly if frequently adjusted or cleaned aggressively.

Symptoms of a bad Leveling Leg include:

• The range tilts or wobbles, making cooking uneven.
• Difficulty sliding pots and pans across the cooking surface due to the appliance not being level.
• Increased strain on other components of the range, which could lead to premature wear or failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The LP Bake and Broil Orifice Kit is an OEM replacement part for Whirlpool gas ranges and ovens. It is a kit containing specially-sized orifices that control gas flow to the bake and broil burners. This allows for optimal gas-air mixture and fuel efficiency specific to liquefied petroleum (LP) gas systems.

Causes of needing a replacement kit include worn or damaged orifices that alter proper gas flow and burner performance over time.

Symptoms include:

• Slow or uneven heating from one or multiple burners
• Burners that create hot or cool spots on cookware
• Ineffective or soft flames that impact cooking results
• Higher appliance operation costs due to inefficient fuel usage

This OEM kit is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Oven orifice kit with Bake orifice and "Male" Broil orifice. For an oven orifice kit with a "Female" Broil orifice, order part# W10859321. The Bake orifice is #56, Broil orifice is #100.

The Grate Set is an OEM part for Frigidaire ranges. This part provides a stable surface for cookware and allowing for even heat distribution during cooking.

Common causes of a bad grate set include prolonged exposure to high heat, heavy impact from dropping cookware, or general wear and tear over time.  

Symptoms of a bad Grate Set include:

• Visible cracks, chips, or warping of the grates
• Difficulty in balancing pots and pans on the grates
• The grates not fitting properly over the burners
• Uneven cooking due to unstable grates

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Latch Hook is an OEM replacement part for LG front load washers. It is a component of the overall latch and locking assembly and works to securely close and lock the washer door. With a properly functioning latch hook, the washer door remains tightly sealed during cycles to ensure optimal water retention and the most thorough cleaning. 

Symptoms of a bad door latch hook include:

• Water leaks around the door during washing cycles
• The door fails to latch fully and unlock after cycles 
• Difficulty opening or closing the washer door completely
• Alignment issues like misaligned or skewed door positions

Causes of a bad door latch hook can include wear over extended use. Damage may also result from washing hard or abrasive items that put excess strain on the latch mechanism over time.

This OEM LG part is compatible with Sears/Kenmore front-load washer models as well. 

The Spark Module is an OEM part for Frigidaire cooktops and ranges. It is responsible for generating the electrical spark that ignites the gas burners. This module sends a high-voltage signal to the igniters, ensuring the burners light up quickly and reliably when you turn the knobs.

Causes of a bad spark module can include electrical surges, wear and tear from regular use, or exposure to moisture, which can lead to corrosion or short-circuits. 

Symptoms of a bad spark module include:

• Burners not igniting
• Weak or intermittent spark
• Clicking sound without ignition
• Some burners working while others do not

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Leveling Leg Assembly is an OEM part for Frigidaire ranges. This part provides stability by allowing users to adjust the height of the range, ensuring it is level and balanced on the floor.  

Causes of a bad leveling leg assembly can include wear from frequent adjustments, damage due to heavy loads, or breakage from accidental impacts.  

Symptoms of a bad leveling leg assembly include:

• The range being uneven or wobbling
• Difficulty in leveling the range using the legs
• Noise or movement when the range is in use
• Doors not aligning properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This genuine replacement gasket restores a tight, reliable seal between mating parts in your appliance to prevent leaks and performance loss. Replacing a worn or damaged gasket helps stop moisture intrusion and keeps the unit operating as designed.

• Forms a compressible barrier to keep air or water from escaping at the joint
• Helps maintain proper operation and efficiency by preserving the intended seal
• Common failure signs: leaks or drips, visible cracks/tears or flattening, hardening/brittleness, or gaps that won't stay closed

• Disconnect power and, if applicable, shut off the water supply before service
• Clean and dry all sealing surfaces; remove old residue or adhesive
• Seat the gasket evenly without stretching; press for full contact all around
• Let the gasket relax at room temperature (or warm slightly) to ease fit, then check the seal after reassembly

This replacement light bulb restores interior illumination inside your appliance. Swap it in for a burned-out bulb so you can clearly see contents and monitor operation when the door opens or the light button is pressed.

• Provides interior light inside the appliance cavity
• Direct replacement for a failed or broken bulb
• Common symptoms: no light when the door opens, flickering/intermittent light, visibly darkened or broken bulb

• Disconnect power to the appliance before servicing
• Allow the old bulb and nearby surfaces to cool completely
• Remove any lens or cover to access the socket; install the new bulb in the same orientation as the original
• Handle with clean, dry hands or gloves; do not overtighten. Restore power and test