Kenmore / Sears Range Parts

Easy fix. Both elements replaced while I was at it, so all new. Figured if one went the other was going to follow. CIRCUIT BREAKER OFF. Removed the back metal panel with my nut driver for the hex head screws. Note where the panel may slip under tabs for support. Remove slip on electrical connections on upper and lower elements. May need a pliers. (I did not want to just pull the element and the wires into the oven with the element and remove them there, like a technician would do. After 15... Read more

The glass was easily replaced. Just a few screws to remove cover then remove bad glass then i dropped in the replacement glass then reinstalled cover. Ithen put the door back in the stove. 15 minute job!!! I was so surprised to see how easy it was!!! Thanks! Part fit perfectly!!! Read more

Replaced switch with a new one. also replaced the 4 knobs Read more

Replaced the element. 1st- Turn off the power to the appliance. The cook top is held on with two screws - access the screws by opening the oven door. Cooktop is hinged, so just pull up near oven door and hold in place with, say, a three foot long stick. The elements are held in place by bracket attached to the cooktop. Remove the bracket by removing the two socket screws. The element is aligned to the bracket with three locking tabs. Remove the tabs with pliers. I broke off one the... Read more

Removing was easy. Pull out the ends of the seal, the ends aren't locked in. Then, pull up on each retaining clip. Each clip is held in with spring tension. Reinstallation was easy too. Start on one end, Twist frayed end into cone-like shape and insert into one of the holes for the seal. Push in with a skewer/screwdriver. Insert first clip into the first hole. Go around in a linear fashion, inserting each clip into each hole. After the last clip is pushed in, twist the end of the frayed end... Read more

• Element will not heat

Ordered new heating coils for stove Read more

I had to order the glass, frame, and cap that the handle attaches to. I just had to put in about 6 screws, it was very simple. Read more

I first checked a repair video and found the procedure was a 10 minute job. I then went to the website, put in my stove model number and searched for the switch. While I was looking I was offered a chat session with one of their experts. I am glad that I accepted. The switch I was looking at was not the right switch for the job. My expert verified my model number and the switch that need to be replaced. After a couple of minutes, she came back with the right part and placed the order for... Read more

Got the window and replaced it no time Read more

Installed the new pans and replaced the coils. My Jennaire looks like new. Only took minutes and made such a difference. Read more

Replaced two switches that controlled two front burners. One controlled three different burner sizes options in one burner. The other was the speed burner, basically three different burner options in one burner. Read more

Fixed it by replacing Valve Control Assemble and Range Oven Igniter, a little intimidating at first,but the videos from Appliance Parts Pro made so much easier.Whenever I need parts for appliance in the future AppliancePartsPros will be my first choice. Read more

The lightbulbs were a problem for me as I did not know if they were 12 V or 120 V. But the interactive parts diagram on the website was very helpful and allowed me to order the correct bulbs very rapidly(120V is correct). They were very easy to change out except for the fact that I needed to have my 12-year-old son do part of it since his hands are smaller than mine.(and it is always good for sons to work with dads even on small projects like this.) The cooking element was also amazingly easy... Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

Ordered the dual element,only took 1 day for delivery,replaced element in about 15 min.and we're back in business Thanks Read more