Kenmore / Sears Range Parts

• Oven not heating evenly
• Oven is too hot
• Little to no heat when baking
• Element will not heat

Ordered spare part that actually fit my oven. Arrived in three days from next state over. Unplugged power cord, removed racks, used 1/4" socket on ratchet with 6 inch extension to remove two sheet metal screws at lower back of oven. Pulled old element out 2 inches then tilted front of element up 45 degrees for spade connectors to clear holes at back of oven. Once clear, pulled element forward until the white #16 wires pulled through the openings in the oven (inside at the back). By hand, gently... Read more

• Little to no heat when baking
• Oven not heating evenly
• Won't start

One day, while trying to roast chicken on the convection roast setting, my Electrolux oven stopped heating properly. I tried the broil setting and the top electric heating element worked fine. I then tried the bake setting and found that the bottom element wasn't working at all. I Googled the problem. The info I found said that the issue was probably that the bake element needed to be replaced. It said to look for a break or burned through spot on the element. If it appeared OK, remove it... Read more

I searched for my appliance and the problem. Applianceparts.com was one of the results. There was one fix-it help from a previous customer. I ordered the piece of glass and somehow it arrived at my home the VERY NEXT DAY! I couldn't believe it. So I followed the exact instructions left by the one person that wrote in. I removed 2 screws at the bottom of the door and 4 at the top which enabled me to disassemble the front and back of the door. I then cleaned all the shattered pieces of glass... Read more

• Element will not heat

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

• Little to no heat when baking
• Oven not heating evenly
• Oven is too hot
• Won't start

Took out old element,got part number and look for the cheapest price online, Appliance Parts Pro could not be beat... order part be number, easy to match, came in fast and put in element, only needed a 5/16 nutdriver to take it out and put it in,unpluged wires and bent just a little to keep one on left and one right from getting mixed up and pluged up new element and ran in the 2 screws,easy job, dont get no easier.. Thanks again Appliance Parts Pro Read more

• Element will not heat

Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails. My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because... Read more

• Little to no heat when baking
• Oven not heating evenly
• Element will not heat
• Oven is too hot

I finally found the right serial number and found the part at Appliance Parts Pros. I was skeptical that they would send the element that had the correct rear brace fixture. when it came 2 days later i opened the box the Part was correct and it took about 15 minutes to replace since there are only two screws. My oven works fine now. THX Read more

On my Jenn-Air downdraft range, the oven stopped heating. The broiler still worked. So pulled the pan off the bottom so I could see and found the igniter wasn't glowing to start the gas. I had replaced the full electronic control panel using Appliance Parts Pros so knew they had the full breakdown of parts for my model. I found the igniter and ordered. But frankly, I wasn't sure about doing the repair myself. It looked easy enough from videos and discussions here. Still, dealing with the... Read more

• Element will not heat
• Won't start

I ORDER THE TERMINAL BLOCK KIT, AND FOLLOW THE VIDEO HOW TO REPAIRE. IT IS VERY EASY.IT TOOK ME 10 MIN. Read more

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

I googled the model number of the oven and came across AppliancePartsPros.com The coil along with replacing video was right at hand. I ordered the part, got it three days later (standard shipping) and installed it. To sum it up, it was a five minute job. Read more

• Little to no heat when baking
• Oven not heating evenly

Watched the appliancepartspro video and changed it out. It took about 15 minutes. I'm sure I saved hundreds. Read more

• Won't start

There are hex screws keeping the igniter in place. I think they were 5/16...so you have to have a socket wrench. The space is kind of tight, and it's all on the right side, so if you're left handed (like I am) it's going to be a challenge to get the hex screws out without dropping them. Dropping them isn't too bad if they don't fall into the hole the gas pipe is coming through. Unfortunately one of them fell in there, and there's no getting it out of there. I had a machine screw that fit, so I... Read more

• Door won't close
• Door stuck closed

This was much easier than expected. I called Appliance Parts Pros with my model # and you told me what part I needed. It was shipped the same day and arrived the next day. I removed the inner door trim with a table knife ( don't rush this or you might crack the trim ). I then unhooked the old door latch disconnected the spring from the door hooked on the spring from the new latch and clipped in the latch to the door. Final step was to reattach the door trim. It was very easy and all I used... Read more

• Doesn't shut off
• No heat
• Won't start

The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more

• Element will not heat

Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros. Read more