Kenmore / Sears Refrigerator Relay, Overload, Capacitor

This capacitor is an electrical replacement part that helps restore reliable motor/compressor start and operation in compatible appliances. Replacing a failed capacitor can stop intermittent operation and reduce abnormal humming or failure-to-start issues. What it does:

• Provides the stored electrical charge needed for motor or compressor start-up and stable operation
• Commonly linked to symptoms like humming, repeated starting/stopping, slow or failed starts, or loss of function
• Stabilizes voltage to reduce stress on motor circuitry and improve run consistency
• Replaces a worn or failed capacitor to restore normal appliance electrical performance

• Disconnect power at the breaker or unplug the appliance before beginning any service
• Capacitors can hold a charge—discharge carefully
• Observe terminal orientation and wire placement; replace with identical specifications

This starter is a small electrical device that helps the refrigerator or freezer compressor start reliably, restoring proper cooling when the compressor struggles to power up. Replace a failed starter to bring the compressor back to dependable operation. What it does:

• Supplies the initial start current to the compressor so it can spin up and begin the refrigeration cycle.
• Common symptoms of a failing starter: refrigerator or freezer not cooling, compressor hums or vibrates but won't run, repeated clicking noises at the back, or intermittent cooling.
• Works with the appliance's existing compressor wiring and start circuit to restore normal starting performance when compatible.

• Always disconnect power to the appliance before attempting any repair.
• The starter typically mounts on or near the compressor and may require pulling the appliance away from the wall and removing the rear access panel.
• Handle terminals and wiring carefully; match connectors and orientation to the original part.

This PTC compressor start relay briefly powers the compressor's start winding to get the motor turning, then drops out as it warms. Replacing a weak relay can restore consistent compressor starts and stabilize refrigerator and freezer temperatures.

• Momentarily energizes the compressor's start winding; disengages automatically as the PTC element heats
• Helps protect the compressor by removing the start winding after startup
• Symptoms of failure can include compressor clicking but not running
• Intermittent cooling or warming temperatures between cycles
• Heat discoloration or a burnt odor around the start device

• Disconnect power and remove the rear lower access panel
• Note wire locations; remove the start device cover/retainer and pull the old relay straight off the compressor pins
• Inspect compressor pins; firmly seat the new relay and reconnect wiring
• Reinstall covers/panels, restore power, and verify normal compressor start

This starter is the compressor's start device. It energizes the start winding so the compressor can begin running, helping restore reliable cooling performance. What it does and common signs it's bad:

• Supplies initial current to the compressor's start winding; disengages once the motor is running
• Symptoms can include a warm refrigerator/freezer, compressor not starting, clicking or humming every few minutes
• Can show heat damage or rattling when shaken after failure

• One compressor starter

• Disconnect power before servicing and pull the unit forward for rear access
• Remove the compressor cover; note wire positions and device orientation
• Firmly seat the new starter on the compressor terminals and reconnect the harness; reinstall the cover
• Restore power and observe compressor start-up; use cut-resistant gloves and follow the product's service information

This compressor start relay (PTC) briefly powers the compressor's start winding to ensure reliable start-up. Replacing a failed relay can stop repeated clicking and help a non-starting compressor restore normal refrigerator cooling.

• Provides a timed, resistance-based boost to the compressor's start winding, then drops out of the circuit
• Common symptoms: compressor hums then clicks off, frequent clicking from the rear, warm fridge/freezer, intermittent cooling
• Mounts directly on the compressor terminals; works with the separate overload protector and, if equipped, a run capacitor
• Visible signs of failure may include heat damage, burnt odor, or loose/rattling pieces inside the old relay

• Unplug the refrigerator and remove the lower rear access panel to reach the compressor
• Note wire routing and orientation; transfer any harness/retainer and seat the relay fully on the compressor pins
• If a run capacitor is present, discharge it before handling and reconnect to the same terminals
• Inspect the overload and connectors; replace any heat-damaged components

Includes relay, overload and cover.

This compressor start device energizes the refrigerator compressor's start winding to begin the cooling cycle, then disengages it. Replacing a weak or failed start device can restore reliable starts and address repeated clicking and warm/no-cool symptoms.

• Provides initial power to the compressor's start winding for reliable startup
• Disengages the start circuit once the compressor is running
• Common failure symptoms: compressor won't start, frequent clicking from the rear, refrigerator or freezer not cooling
• Heat damage or burnt odor on the old device may be present when it fails

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove the rear access panel to reach the compressor compartment
• Note wire positions; if your model uses a separate run capacitor, transfer it; move wires to the new device one at a time
• Align the device with the compressor terminals and press straight on until fully seated; reinstall any cover or retainer

This start relay controls power to the compressor's start winding so the refrigerator can start and run. Replacing a weak or burned relay restores dependable compressor start-up and can stop repeated clicking with warming temperatures.

• Energizes the compressor's start winding to provide initial torque, then disengages from the circuit
• Common failure symptoms: refrigerator not cooling or intermittently warm; compressor hums/clicks and won't start; relay rattles, smells burnt, or shows heat damage; overload trips
• Helps prevent hard-start conditions that stress the compressor
• The relay contacts are open/shorted, the compressor may fail to start and cycle off on overload

• Disconnect power before servicing; wear appropriate PPE
• Access the rear machine compartment; remove the relay cover on the compressor. Note wire positions, pull the old relay straight off the compressor pins, transfer wires, and fully seat the new relay in the same orientation
• If equipped, safely discharge the run capacitor; inspect the overload, wiring, and terminals for heat damage and address as needed
• Reinstall the cover. If the compressor still won't start, further diagnosis of the start device, capacitor, or compressor is required

This refrigerator compressor starter is the start device that plugs onto the compressor terminals. It briefly energizes the start winding so the compressor can start reliably, helping restore cooling when the original starter fails. What it does:

• Engages and then disengages the compressor's start winding during startup
• Mounts directly on the compressor pins under the terminal cover
• Common symptoms of a failed starter: not cooling, rapid clicking/humming from the compressor area, compressor hot but not running, or intermittent starts
• Replaces the original start device specified in your model's parts diagram

• 1 compressor starter

• Disconnect power before servicing; pull the unit out to access the back panel
• Remove the compressor terminal cover; note/photograph wire positions and orientation
• Pull off the old starter; inspect the overload and wiring for heat damage
• Align with the compressor pins and press on firmly; reinstall the cover and restore power

A thermal overload protector that helps prevent motor damage by cutting power if the dryer motor overheats. Fits the motor assembly and restores normal operation once the motor cools. What it does:

• Detects excessive motor temperature and interrupts power to prevent motor burnout
• Helps stop the motor from running when overheating occurs
• Commonly replaced when the dryer won't start or the motor hums but does not turn
• Can prevent further electrical damage by opening the circuit during thermal faults

• One thermal overload protector

• Disconnect power to the appliance before servicing to avoid shock or injury
• Located on or near the dryer motor; note wire locations or take a photo before removal
• Replace with the correct PN and secure terminals firmly; do not force connections
• Check motor bearings, start components, and wiring if symptoms continue after replacement

A replacement motor start/run capacitor that helps restore reliable motor starting and smooth operation for compressors and fans. Installing the correct capacitor can reduce hard-starts, humming and intermittent motor operation. What it does:

• Provides the temporary boost motors need to start and stabilize while running.
• Helps compressors and fan motors start more easily and run more efficiently.
• Commonly associated with symptoms like humming, motors that won't start, intermittent operation, or reduced cooling performance.
• Prevents repeated motor stress that can lead to overload trips or premature motor wear.

• Disconnect power to the appliance before accessing electrical components.
• Discharge the capacitor and tag/photograph wire locations before removal to ensure correct reinstallation.
• Replace with the exact OEM part or an approved equivalent; do not bend or puncture the capacitor can.

This refrigerator compressor start device provides the initial boost the compressor needs to start, then disengages. Replacing a failed start device helps restore reliable compressor startup and steady cooling performance.

• Supplies momentary power to the compressor's start winding to get the motor running
• Disengages after startup so the compressor can run normally
• Typical failure symptoms: refrigerator warm or not cooling, compressor won't start, rapid clicking from the compressor area, or intermittent cooling
• Located on the side of the compressor at the back of the appliance

• Unplug the refrigerator and allow the compressor area to cool before servicing
• Access the compressor at the rear; note wire positions and the device orientation
• Pull the old device straight off the compressor pins; seat the new device fully and reconnect wires securely
• If your model uses a separate run capacitor, transfer and reconnect it exactly as originally configured

This relay assembly helps start the refrigerator compressor so the cooling system can run reliably. It replaces a worn or failed start relay to restore normal compressor startup and reduce hard-start symptoms. What it does:

• Provides the initial start pulse to the compressor motor so the refrigeration cycle can begin
• Stops excessive current draw during startup to protect the compressor
• Commonly used when the compressor hums, won't start, or cycles on and off rapidly
• Helps eliminate starter-related clicking or failure-to-start issues

• Disconnect power to the appliance before inspecting or replacing the relay
• Handle electrical connectors carefully; ensure secure, correct reattachment
• Verify match to the existing relay and mounting before installation

This overload protector is a safety device that helps prevent compressor damage by stopping electrical current during overheating or locked-rotor conditions. It's a direct-fit replacement that restores proper compressor protection and helps keep the appliance running safely. What it does:

• Protects the compressor by interrupting power if the motor overheats or experiences an electrical fault
• Common symptom: refrigerator runs but compressor won't start or only hums
• Common symptom: fridge cycles frequently or doesn't maintain temperature due to compressor protection tripping
• Works with the start device to help ensure reliable compressor startup

• Disconnect power before servicing; work only with the appliance unplugged
• Access typically requires removing the rear access panel to reach the compressor area
• Replace using the same mounting and terminal connections; ensure secure electrical connections

This start device helps the appliance motor get up to speed so the unit starts and runs reliably. It's a direct-fit replacement that restores proper starting operation when the motor hesitates or won't start. What it does:

• Provides the initial boost or timing signal the motor needs to start turning
• Commonly replaces a failed start component when the motor hums but won't begin running
• Helps stop repeated start attempts that can overload the motor or trip protection
• Works as part of the motor starting circuit to ensure smooth startup

• Disconnect power to the appliance before attempting any repair to avoid shock or injury
• Handle the part carefully and match connectors/terminals to the original during replacement
• Basic hand tools are typically required; keep track of screws and wire routing

This PTC starter helps the compressor start by briefly supplying the correct current at startup, restoring reliable cooling when the compressor struggles to kick on. Compact replacement for failed or weak start devices. What it does

• Provides a timed boost to the compressor start winding so the compressor can start reliably
• Commonly used when a refrigerator or freezer won't start or hums without running
• Helps prevent frequent hard starts that can overheat the compressor
• Passive solid-state design with no moving parts for simple, maintenance-free operation

• Disconnect power to the appliance before inspecting or replacing the starter
• Handle electrical connections carefully; install the starter in the same orientation and wiring position as the original
• If the compressor or start relay shows additional damage, replace those components.