Kenmore / Sears Refrigerator Relay, Overload, Capacitor

Fridge not cooling but lights work? This compressor overload stops overheating and prevents startup damage. DIY-friendly repair in about 1 hour.

Refrigerator not cooling or compressor running hot? This start device kit includes relay and overload to restore proper compressor function. DIY install.

This capacitor stores and releases electrical energy to support the appliance's circuit during startup and operation. Replacing a weakened capacitor can restore reliable performance and reduce humming, hard starting, or stalling in the affected component.

• Provides a power boost at startup and helps stabilize voltage during operation
• Helps the connected component start promptly and operate smoothly under load
• Common failure signs include humming, slow or no start, or intermittent operation
• Contribute to overheating or a tripped breaker/fuse when the component tries to start

• Disconnect power at the breaker or unplug the appliance. Before handling, safely discharge the old capacitor using a proper resistor-rated tool.
• Photograph or note wire positions; move each lead to the same-labeled terminal on the new capacitor and ensure snug connections.
• Mount the capacitor securely in its bracket; keep terminals covered and clear of metal surfaces.

This controller kit is the appliance's main electronic control. It reads inputs from the user interface and sensors to power and coordinate key components. Replacing a failed controller restores responsive controls and consistent, reliable operation.

• Interprets commands from the keypad and sensors to manage operation
• Controls relays powering motors, fans, compressor, or valves as designed
• Coordinates modes and cycle timing for proper performance
• Common symptoms: dead or blank display, unresponsive buttons, won't start, intermittent shutdowns, or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board with ESD precautions; avoid touching connectors and components
• Photograph/label wire connections and transfer them one at a time to the new board
• After installation, verify any model-specific settings per the service documentation before testing

This kit includes the electrical components needed to start your refrigerator's compressor motor, including both the start relay and overload protector. These parts work together to provide the initial electrical boost needed to start the compressor and protect it from electrical overload. Replace this kit if your refrigerator isn't cooling, makes clicking noises, or if the compressor won't start.

Refrigerator won't cool or compressor won't start? This compressor start relay energizes the start winding to restore cooling. DIY-friendly repair.

Refrigerator clicking but not cooling? A failed compressor start device causes repeated clicking and warm temps. Quick DIY fix restores reliable starts.

Fix a refrigerator that won't start or hums but doesn't run with this compressor start capacitor. Restores reliable cooling when the compressor fails to start.

Refrigerator won't start or stops running? A failed capacitor disrupts motor circuits. This film radial capacitor restores voltage stability and operation.

Freezer won't cool or compressor won't start? This compressor start relay restores reliable startup and cooling. Located in the compressor compartment.

Fix a refrigerator that won't cool or compressor runs briefly then stops. This PTC starter relay provides timed boost to start winding for reliable cooling.

Fix a refrigerator that won't cool or run with this compressor overload protector. Prevents compressor damage from electrical overheating. Easy install.

Refrigerator not cooling or compressor not running? This relay overload protector prevents compressor damage by cutting power during overload conditions.

Refrigerator won't cool or compressor won't start? This overload protector prevents compressor damage from electrical surges. Simple 15-minute fix.

Fix a refrigerator compressor that won't start or runs hot with this overload protector. Protects the compressor from electrical damage. DIY repair.

The Refrigerator Main Switch Assembly is an essential component designed to maintain the optimal performance of your Samsung refrigerator. This genuine OEM part ensures a perfect fit and reliable operation, seamlessly integrating with your applianceGÇÖs existing systems. The main switch assembly controls the power distribution within the refrigerator, allowing you to efficiently manage cooling cycles and maintain consistent temperatures. By replacing a faulty main switch with this high-quality assembly, you can restore your refrigeratorGÇÖs functionality and extend its lifespan. Installation is straightforward, making it an ideal choice for DIY repairs and saving you the cost of professional service. Using a genuine OEM part guarantees compatibility and durability, providing peace of mind that your refrigerator will continue to operate smoothly. Enhance the reliability and efficiency of your Samsung refrigerator with the Refrigerator Main Switch Assembly , ensuring your appliance remains a dependable part of your kitchen.