Kitchenaid Dishwasher Parts

This left-hand (LH) support is the factory replacement bracket that secures and aligns the left side of its assembly, helping keep parts level and operating smoothly. Replacing a damaged support restores proper fit and reliable function.

• Provides structural support and alignment on the left-hand (LH) side
• Helps keep connected components level and properly spaced
• Common symptoms: cracked/broken support, wobbling or sagging parts, misalignment, rubbing or binding during use
• Typical causes: wear, stress/impact, overloading, or overtightened fasteners

• Disconnect power before servicing; shut off water supply if applicable. Wear cut-resistant gloves.
• Clear the area for access. Note the original orientation and retain any screws/clips for reuse.
• Install the new LH support in the same position and ensure it aligns with the opposite side.
• Check fit and operation before fully reassembling.

This hanger anchors the dishwasher's door-balance spring to the frame so the door opens and closes smoothly. Replacing a worn or broken hanger restores proper spring tension and helps prevent a door that drops, slams, or feels heavy.

• Secures the door balance spring to the dishwasher cabinet/frame
• Maintains correct spring tension for smooth, controlled door movement
• Helps fix a door that falls open quickly or won't stay in position
• Useful to replace when door balance hardware shows wear or damage

• Disconnect power and shut off water before servicing; remove the toe panel/kickplate
• Support the door and carefully relieve spring tension before removing parts
• Slide the dishwasher out if needed for side access; transfer the spring to the new hanger and reinstall
• Inspect the opposite-side spring/link and hinge for wear; verify door balance before reassembly

Color: light gray. Measures about 3 inches high by 6 inches deep.

Color: Black

The Rack Support (RH) is an OEM part for Whirlpool dishwashers. It is the plastic right-hand side bracket that secures the upper rack assembly inside the washer cavity. 

Causes of a damaged rack support include cracks or breaks from normal wear over extended use. Repeated impact from dishes loading/unloading can cause small stress fractures.

Symptoms of a faulty support include:  

• Loose or rattling upper dish rack during operation
• Difficulty sliding racks in/out smoothly
• Visible cracks or missing pieces on the support

This Whirlpool OEM part is also compatible with Maytag, Jenn-Air, KitchenAid, and some Kenmore models.

This door spring counterbalances the door so it opens smoothly and doesn't drop. Replacing a fatigued or broken spring restores proper door feel and helps protect hinges and related components from excess strain.

• Provides the tension that balances the door during opening and closing
• Helps prevent the door from slamming or falling open too quickly
• Replaces a stretched, weakened, or broken spring
• Common signs: door feels heavy, drops quickly, or sits unevenly side-to-side

• Disconnect power before servicing; for dishwashers, also shut off the water supply
• Support the door and carefully relieve spring tension before removal
• Install the new spring in the same attachment points/orientation as the original
• Replace both together to maintain even tension

This replacement upper spray arm restores strong spray coverage to the upper wash level of your dishwasher. It channels water through its jets and spins under pressure to help deliver consistently clean dishes on the top rack.

• Directs pressurized wash water to the upper wash level for thorough cleaning
• Rotates under water pressure for even spray coverage
• Helps clear food soils and detergent residue from dishes and glasses
• Common symptoms: poor cleaning on the upper rack, spray arm not spinning, clogged or cracked arm

• Disconnect power and shut off the water supply before servicing
• Open the dishwasher; remove the upper rack if needed for access
• Release or unthread the retainer and pull the old arm straight off; clear debris from the hub/feed port
• Seat the new arm and secure the retainer hand-tight; ensure the arm spins freely and run a test cycle

This overfill control float assembly sits in the dishwasher tub and rises with the water level. It works with the float switch to shut off the inlet valve, helping prevent overfilling and potential leaks.

• Rises with the water level to engage the float switch and stop water flow
• Helps protect against tub overfill and floor leaks during the fill cycle
• Replace if the float is missing, warped, stuck, or doesn't move freely
• Symptoms can include continuous filling/overfilling, water spilling from the door, or no fill if the float is stuck in the up position

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift the old float straight up from the tub opening
• Clear any debris from the float well so the new float moves freely
• After reassembly, start a fill to ensure the float rises and water shuts off

This mount secures the dishwasher's upper spray arm to its water feed, keeping the arm aligned and free to rotate so the upper rack receives consistent spray coverage and dependable cleaning.

• Supports and centers the upper spray arm at the correct connection point
• Helps maintain a solid connection to the feed tube/manifold for proper water delivery
• Wear, cracks, or looseness may lead to poor cleaning on the upper rack, arm wobble, or noise
• Replacing a damaged mount can help restore smooth spray arm rotation and wash performance

• Disconnect power and turn off water supply before servicing
• Pull out the upper rack; remove the upper spray arm from its mount
• Release the old mount's locking tabs or fasteners and remove it from the feed tube/tub
• Install the new mount fully, reattach the spray arm, and verify it spins freely before testing

Color: White

The Dishwasher Filter Screen is an OEM part for Whirlpool dishwashers. As a key filtration component, the filter screen traps food particles and debris to prevent clogs and ensure optimal water circulation during wash cycles. It is responsible for filtering out contaminants and protecting internal pump components from damage.

Symptoms of a bad filter screen include:

• Reduced or uneven water pressure during wash cycles  
• Puddles or pooled water inside the dishwasher
• Food debris caught in the pump or other areas  
• The dishwasher fails to fill or drain properly
• Unusual noises emanating from the dishwasher

Causes of a bad filter screen can include clogging over time due to accumulated food waste and mineral deposits or damage such as cracks or tears in the screen material.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

This genuine replacement door handle restores a solid, comfortable grip for opening and closing your appliance's door. Replace a cracked, loose, or missing handle to keep daily use safe and the appliance looking factory-clean. What it does:

• Provides the handhold needed to open and close the door
• Transfers pull force to the door without stressing the latch
• Helps ensure the door can be operated safely and consistently
• Common symptoms: handle cracked, broken, loose, spinning, or missing

• 1 door handle

• Disconnect power before servicing; allow hot surfaces to cool
• Protect surrounding surfaces; support the door if required by your model
• Access the mounting screws as directed by your service manual; note screw locations and any spacers
• Tighten screws evenly without overtightening; wear cut-resistant gloves

This upper rack adjuster sets and secures the dishwasher's top rack height so dishes clear the spray arms and load properly. When the adjuster wears or breaks, the rack can become uneven or stuck, leading to poor cleaning and loading issues.

• Provides the mechanism to raise/lower and lock the upper dishrack height
• Keeps the top rack level and secured to the rail during operation
• Common symptoms of failure: rack drops on one side, won't adjust, feels loose, or comes off the track
• Contribute to poor wash results when the rack can't be positioned correctly

• Disconnect power and water supply before servicing
• Remove upper rack end caps/stops and slide the rack out to access the adjuster
• Release or unfasten the old adjuster, transfer any reusable clips/wheels if applicable, and install the new adjuster
• Set both sides of the rack to the same height; reinstall rack and confirm smooth travel and secure locking

This adjustable manifold connects the upper rack to the dishwasher's rear water feed. It channels wash water to the upper spray arm and maintains a sealed connection as the rack height changes for consistent cleaning performance. What it does:

• Routes water from the rear feed tube to the upper/middle spray arm
• Self-adjusts with rack position to keep a secure, leak-resistant connection
• Replace if cracked, deformed, or the coupling no longer seals
• Common symptoms include poor cleaning on the upper rack, weak spray, upper spray arm not turning, or a small leak at the back of the tub

• 1 adjustable manifold

• Disconnect power and shut off water; wear gloves for protection
• Remove the upper rack by releasing the rail end caps and sliding the rack out
• Unclip the manifold from the rack and disengage it from the rear feed port; seat the new manifold fully
• Reinstall the rack and ensure the spray arm spins freely

This is a Whirlpool control board intended for use with dishwashers.The control board is a critical component of the dishwasher as it controls the cycles and functions, including the draining and drying cycles. Control boards are subject to wear and tear that can render them ineffective and require them to be replaced prior to the standard lifecycle of the appliance. Unplug the dishwasher from both the power and water sources before attempting to replace the control board to prevent serious electrocution injuries. Work gloves should also be worn.This OEM control board has been sourced from the manufacturer and is compatible with dishwashers from Whirlpool, Maytag, Kitchenaid, Magic Chef, Admiral, Norge, and other brands. This part has been made from high-quality, durable, non-corrosive materials and is only sold individually.

This user interface is the electronics behind a full-door console dishwasher panel. It reads your button selections and communicates with the main control so cycles start and options respond reliably.

• Interprets keypad inputs from the console and sends commands to the control board
• Helps restore proper control of wash cycles, options, and start/delay functions
• Common symptoms: unresponsive or intermittent buttons, no console lights, can't start from the panel, erratic beeping/stuck-key behavior
• Built for full-door (full-console) configurations used on select models

• Disconnect power at the breaker; turn off the water supply
• Remove inner door/console screws to access the UI; support the panel to avoid straining wires
• Handle the board with ESD care; transfer any mounting clips/brackets and seat ribbon cables/connectors fully and correctly
• Reassemble the door and test console operation before running a full cycle