Kitchenaid Dishwasher Parts

Drain hose that diverts wastewater from your dishwasher to the disposal or drain pipe. Replace if cracked, leaking, or disconnected from the sump assembly.

Replacement tub wheel that supports and guides the washer drum for smooth, aligned rotation. Replace worn wheels to reduce drum noise, rubbing and uneven spinning. What it does:

• Supports and guides the washer drum so it turns smoothly and stays aligned.
• Reduces friction between the drum and cabinet, helping prevent scraping or binding.
• Replace if the drum squeaks, drags, rubs, or wobbles during spin cycles.

• Disconnect power and turn off water supply before servicing the appliance.
• Access may require removing the cabinet, front or rear panel depending on model.
• Inspect adjacent shafts, bearings and mounts for wear and replace if needed.
• Reassemble and test the washer after installation to ensure proper drum movement.

Fix leaking dishwasher or water overflowing onto the floor. This float assembly rises with water level to prevent overfills. Easy 5-10 minute repair.

Adjustable manifold that connects the upper rack to the rear water feed tube. Replace if cracked, punctured, corroded, or missing the seal probe.

Dishwasher won't start, stops mid-cycle, or shows error codes? The control board manages all cycles and functions. Moderate DIY repair in 30-60 minutes.

Seals blender jar to base preventing leaks. Replace if cracked, worn, or leaking occurs. Confirm fit with your model number before ordering.

Replacement dishwasher mounting screw secures panels, brackets, and internal components. Needed when original fasteners are missing, stripped, or damaged.

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

Replaces cracked, broken, or missing lower access panel on your dishwasher. Covers the base opening for a finished look and shields internal parts.

12 Ft in length

Dishwasher drain hose channels wastewater from the pump to your home plumbing. Replace if cracked, kinked, clogged, or leaking to restore proper drainage.

Replace cracked or worn dishwasher dishrack wheels that guide the upper rack in and out smoothly. Single wheel for convenient loading and unloading.

This upper rack adjuster sets and secures the dishwasher's top rack height so dishes clear the spray arms and load properly. When the adjuster wears or breaks, the rack can become uneven or stuck, leading to poor cleaning and loading issues.

• Provides the mechanism to raise/lower and lock the upper dishrack height
• Keeps the top rack level and secured to the rail during operation
• Common symptoms of failure: rack drops on one side, won't adjust, feels loose, or comes off the track
• Contribute to poor wash results when the rack can't be positioned correctly

• Disconnect power and water supply before servicing
• Remove upper rack end caps/stops and slide the rack out to access the adjuster
• Release or unfasten the old adjuster, transfer any reusable clips/wheels if applicable, and install the new adjuster
• Set both sides of the rack to the same height; reinstall rack and confirm smooth travel and secure locking

This upper dishrack track mounts to the dishwasher tub wall and provides a smooth glide path for the rack rollers. Replacing a damaged track restores easy in-and-out movement and helps keep the upper rack aligned and secure.

• Guides and supports the upper dishrack as it slides in and out
• Maintains rack alignment to prevent binding or derailing
• Typical failure signs: rack jams or falls off, rough/squeaky travel, visible cracks or breaks in the track
• Can keep the rack from fully sliding in, making the door harder to close

• Disconnect power and turn off the water supply before servicing
• Remove the upper rack by releasing the end caps/stops
• Unfasten the old track from the tub (screws/clips), then position and secure the new track
• Reinstall the rack and end caps; verify smooth rack travel before restoring power and water

Replace this dishwasher inlet/outlet seal to stop water leaks at connection points and restore proper flow. Essential when you notice dripping or pooling.

Fix dishwasher lights that won't blink or buttons that don't respond. This user interface board reads your selections and starts cycles reliably.