Kitchenaid Dishwasher Parts

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

This electronic control board is the appliance's command center. It reads inputs from switches and sensors, then directs power to components to run selected cycles—helping restore reliable operation when the original board fails.

• Coordinates timing and power to key components
• Interprets user commands and sensor feedback
• Manages cycle logic and stores/communicates fault codes
• Failure symptoms include no power, unresponsive controls, cycles that won't start or complete, or intermittent operation/error codes

• Disconnect power at the breaker before servicing
• Use ESD precautions; handle the board by the edges and avoid touching circuitry
• Note/photograph wiring and move connectors one at a time to the new board
• Inspect connected loads (motors, heaters, valves, fans) for shorts before powering up the new board

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

This electronic control board is the dishwasher's brain, managing cycles and powering the pump, valve, heater, and other loads. Replacing a failed board restores normal start, wash, drain, and dry functions.

• Coordinates and times wash cycles based on user selections and sensor inputs
• Sends power to the circulation pump, drain pump, water inlet valve, and heater
• Interfaces with the user interface and monitors door/latch status
• Failure may cause: no start, cycle won't advance or ends early, no fill/drain/heat, or error codes

• Disconnect power at the breaker before servicing; verify power is off
• Access location varies by model; commonly behind the lower toe panel or inside the console
• Handle the board by the edges and observe ESD (anti-static) precautions
• Move wire connectors one at a time from the old board to the new, secure the board, and reassemble; run any required diagnostics/reset per your model's tech sheet

Color: Black

Color: White. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For grey order 676458. To attach these tine tips you will need to order the dishrack white touch-up paint WP676453.

This overfill float and shaft assembly monitors the dishwasher's water level. As the tub fills, the float rises and triggers the float switch to shut off the inlet water, helping prevent overfilling and leaks.

• Senses tub water level and moves up/down with the water
• Activates the float switch to stop filling at the correct level
• Helps protect against overfill-related leaks
• Common symptoms include: won't fill (float stuck up), continuous filling/overfilling (float stuck down or damaged), or float not moving freely

• Disconnect power and turn off the water supply before servicing
• Lift the old float straight up from inside the tub; access the underside (behind the toe panel) as needed to release the shaft from the float switch lever
• Install the new shaft through the guide and onto the switch lever; seat the float so it moves freely
• Verify smooth float movement and test a fill cycle while checking for leaks

Color: Stainless

The Top Spray Arm is an OEM part for Whirlpool dishwashers. It serves an important role on the upper rack, directing a spray of water across dishes during the wash cycle to thoroughly clean all surfaces. As a rotating component, the top spray arm endures constant motion which can cause wear over time.

Causes of a bad top spray arm include deterioration or cracks in the plastic from extended use, or blockages that restrict water flow.

Symptoms of a bad top spray arm include:

• Incomplete cleaning of upper rack dishes
• Buildup of food debris or grime that won't rinse away
• Noticeably weaker spray pattern from the arm nozzles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This electronic control board is the dishwasher's main circuit board. It directs wash, drain, and dry functions and coordinates the user interface. Replacing a failed board restores responsive controls and reliable, complete cycles.

• Times and sequences wash, drain, and dry operations
• Distributes power to the circulation pump, drain pump, inlet valve, and heating circuit
• Monitors sensors and door switch; communicates with the display/indicator lights
• Common symptoms: won't start, unresponsive controls, cycles that stall or never advance, blinking lights or error codes

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use ESD protection and handle the board by its edges
• Label/photograph connectors; transfer any mounting brackets or jumpers from the original board
• Some models require configuration/programming after install—follow the tech sheet stored inside the unit

Color: Stainless   Note: Comes with Allen wrench, spare set screw, and instructions.

This speed control regulates and stabilizes motor speed in your appliance. Replacing a faulty control restores smooth start-up and accurate speed selection so the motor runs consistently at the setting you choose.

• Modulates power to the motor to reach and hold the selected speed
• Helps correct issues like surging, stalling, or running only at one speed
• Common symptoms include erratic speeds, failure to start, or sudden speed changes
• Also presents as an unresponsive speed selector or inconsistent performance

• Disconnect power before servicing and allow components to discharge
• Access the control per your model's service information; note wire locations or take photos
• Transfer connectors one at a time; seat fully and handle electronics with ESD care
• Reassemble and test operation through all speed settings; perform any model-specific calibration if required

This is the dishwasher manifold tube only. It attaches to the bottom of the upper rack. For the complete kit order 675808. Also consider checking the mount that attaches this manifold tube to the dishrack. For the mount order WP8539324.

Notes: Only one screw hole is used now.

includes seal

This electronic control board is the appliance's central controller, managing critical functions and timing. Replacing a failed board restores proper operation, responsive controls, and consistent performance when the unit is unresponsive, shows errors, or behaves unpredictably.

• Processes user commands and internal signals to run cycles as designed
• Controls or communicates with motors, valves, fans, and heaters through onboard components
• Manages timing, temperatures, and safety checks programmed by the manufacturer
• Symptoms of failure: won't power on or start, dead or erratic controls, error codes, intermittent operation

• Disconnect power to the appliance before servicing; also shut off gas/water
• Use anti-static precautions and handle the board by its edges
• Photograph connections; transfer connectors one at a time to the new board; secure in the original mounting
• After installation, follow your model's tech sheet for any required initialization/diagnostics and verify normal operation