Kitchenaid Dishwasher Parts

Replacement spring kit that restores proper tension and balance to appliance doors and lids, helping them open and close smoothly and stay in position. Use this kit to replace worn or broken springs that cause sagging or noisy operation. What it does:

• Replaces worn or broken door/lid springs to restore proper tension and balance.
• Helps the door or lid open and close smoothly and remain in the desired position.
• Reduces sagging, bouncing, slamming, and related noise caused by failed springs.
• Prevents additional wear on hinges and closures by restoring correct alignment and support.

• Disconnect power (and water, if applicable) before starting any repair; follow all safety instructions in the appliance manual.
• Support the door or lid during removal and installation to avoid pinch or crush injuries.
• Use proper hand protection and tools; keep small fasteners organized to avoid loss.

The Dishrack Wheel is an OEM part for Whirlpool dishwashers. Each wheel works to smoothly guide the upper dishrack in and out of the dishwasher for convenient loading and unloading of dishes.

Causes of a bad wheel can include normal wear and tear from years of use or warping/bending due to overloading of the dishrack.

Symptoms of a bad dishrack wheel include:

• Noisy operation of the dishrack as it moves
• Difficulty fully extending or retracting the rack
• Binding or jamming that prevents smooth travel

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 7 foot long.

The Check Valve is an OEM part for Whirlpool dishwashers. This valve is a component that allows water to flow in one direction only, from the water inlet into the dishwasher. 

Causes of a bad check valve can include mineral or debris buildup interfering with the valve operation over several years of use. Damage is also possible if the water connection is faulty.

Symptoms of a bad check valve include:

• Water flowing backward out of the dishwasher or inlet hose
• Inability to properly fill or circulate water during cycles  
• Potential leaks or standing water below the appliance

This essential Whirlpool replacement is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and Kenmore models as well. 

This handle spring restores tension to the door latch handle so the dishwasher door latches securely and the handle returns to position. Replace a worn or broken spring to address loose handle feel or doors that pop open during a cycle. What it does:

• Provides return tension for the door latch/handle mechanism
• Helps keep the door closed and latched during operation
• Restores proper handle feel and return action
• Common symptoms include a loose or floppy handle, door not latching or starting, or door opening mid-cycle

• 1 spring

• Disconnect power at the breaker and shut off water before servicing
• Remove inner door panel screws to access the latch area; support the outer panel
• Note spring orientation and attachment points before removal; transfer the new spring to the same tabs/holes
• If your latch uses two springs, replace both for even tension; test latch operation before reassembly

The Silverware Basket is an OEM component specifically designed for Whirlpool dishwashers. Located at the bottom outer edge of the tub, the silverware basket provides designated silverware basket dishwasher spacing to properly clean utensils away from other dishes. 

Composed of crisscrossing finger prongs attached to a reinforced circular base, the basket holds forks, knives, and spoons upright safely in place during wash cycles. Its lightweight plastic construction flexes under pressure without breaking or cracking.

Symptoms of a bad silverware basket include:

• Loose or falling utensils obstructing other spray jets   
• Dull or improperly cleaned silverware after cycles
• Visible cracks, chunks missing, or sharp prongs

Replace with this OEM Whirlpool basket to restore form-fitting function. This part fits Whirlpool, KitchenAid, Jenn-Air and select Maytag and Amana dishwashers.

The Rotating Handle is an OEM part for Whirlpool mixers. It allows you to raise and lower the mixing bowl for convenient access during the mixing process.

A bad rotating handle can be caused by regular use, accidental damage, or excessive force applied during operation. If you notice cracks, a loose or wobbly fit, or difficulty in rotating the handle smoothly, it may indicate a problem with the handle itself.

Symptoms of a bad rotating handle include:

• Cracked or damaged handle surface
• Loose or insecure fit of the handle on the mixer
• Inability to raise or lower the mixing bowl 

Replace your faulty handle with this genuine OEM part to restore your mixer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Fits most Kitchen Aid dishwashers. Replaces old 2 coil valves.

This manifold channels wash water within the dishwasher's spray system. Replacing a damaged or clogged manifold helps restore proper water flow and cleaning performance while reducing the chance of leaks at internal connection points.

• Routes high-pressure wash water through the dishwasher's spray system
• Maintains a sealed path to help prevent internal leaks
• Supports consistent spray pressure for effective cleaning coverage
• Helps resolve symptoms such as poor cleaning, weak spray, leaks, or visible cracks in the manifold

• Disconnect power and turn off the water supply before servicing
• Access from inside the tub; remove racks or panels as needed to reach the manifold
• Release retaining clips/screws and note the manifold's orientation; inspect any related seals/O-rings and replace if worn
• Reassemble and run a short cycle to check for proper spray and leaks

This rack track assembly guides the dishrack as it slides in and out, keeping it aligned and stable. Replacing a worn or broken track restores smooth rack movement and helps prevent derailing and uneven loading.

• Supports and guides the rack for smooth sliding action
• Maintains rack alignment to prevent wobbling or tipping
• Replaces cracked, warped, or broken rack tracks
• Common symptoms: rack binds, won't extend fully, falls off/derails, or sits unevenly

• Disconnect power to the appliance before servicing
• Pull the rack forward and release any rack end stops per your model
• Remove the old track, position the new track, and fully engage mounting tabs/clips
• Reinstall stops and verify the rack slides smoothly

This control panel replaces a cracked, worn, or unresponsive console so your appliance can reliably accept cycle and option selections again, restoring a clean appearance and smooth button action.

• Provides the interface area for selecting cycles and options
• Houses and aligns user-interface components and mounting hardware
• Protects and routes the UI connector/ribbon, when present
• Restores proper fit and finish on the front/top of the unit
• Typical symptoms: cracked or broken console, buttons binding or sticking, worn labels, or selections not registering when the touchpad is integrated into the console on your model

• Disconnect power to the appliance before servicing
• Remove screws to access the console; note hardware locations and wire/ribbon routing, and use care around sharp edges
• Handle any ribbon/IDC connectors by the stiffener; seat fully and level
• Transfer any reusable clips, brackets, or overlays/nameplates from the old panel; test keys before final reassembly

Color: White

This circulation pump and motor assembly moves wash water through your dishwasher's spray arms to clean dishes. Replace a worn or seized wash motor to restore proper spray pressure, quieter operation, and consistent cleaning performance.

• Circulates wash water through the spray arms during wash and rinse cycles
• Restores cleaning performance when the original wash motor won't run or is weak
• Typical symptoms: no/weak spray action, dishes still dirty, loud humming or grinding during wash
• Leaks at the pump housing or shaft area can indicate the assembly has failed

• Disconnect power at the breaker and shut off the water supply before servicing
• Remove the toe panel and slide the dishwasher out to access the underside
• Have a towel or pan ready for residual water; disconnect wiring and hoses, noting their orientation
• Transfer and secure existing clamps/mounting hardware as needed; ensure seals are properly seated and test for leaks after reassembly

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

The Track Stop is an OEM part for Whirlpool dishwashers. It is a component located on the tracks inside the dishwasher that holds and guides rack movement during operation. 

Symptoms of a bad track stop include:

• Racks or dishes sliding uncontrollably during the cycle  
• Difficulty fully extending or retracting racks
• Noise or grinding sounds noticed from rack movement
• Damage or wear visible on the rack tracks

Causes of a bad track stop can be a failure due to normal wear and tear over repeated use. Opening and closing the dishwasher door thousands of times can degrade track stops.

This OEM Whirlpool replacement track stop ensures proper rack guiding, securing its position to deliver dependable performance cycle after cycle. This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Upper Rack Tub Mount Roller is an OEM part compatible with Whirlpool dishwashers. It is located in the upper rack and plays an important role in providing a smooth movement of dishes across the rack. The roller enables seamless movement of dishes in and out during loading and unloading. 

Causes of a bad roller can include wear and tear from repeated use, damage from overloading or unbalanced loads, or debris buildup that prevents proper rolling.  

Symptoms of a bad Upper Rack Tub Mount Roller include:

• Dishes getting stuck or stuck in the upper rack
• Difficulty sliding dishes in and out of the upper rack  
• Noisy or grinding sounds coming from the upper rack area
• Upper rack that does not move smoothly

 This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.