Kitchenaid Dryer Parts

The Light Socket Kit is an OEM part for Whirlpool refrigerators. This kit includes the light socket and necessary components to ensure proper installation and functionality. It is designed to hold the refrigerator light bulb securely and provide reliable electrical connections to illuminate the interior of the refrigerator.

Common causes of failure include wear and tear, corrosion from moisture, or damage from handling or bulb replacement.

Symptoms of a bad Light Socket Kit include:

• Refrigerator light not turning on
• Flickering or intermittent lighting
• Visible damage or corrosion on the socket
• Burned or melted areas around the socket

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Door Switch is an OEM part for Whirlpool refrigerators. It is designed to detect when the refrigerator or freezer door is open or closed. This switch controls the interior light and ensures that the cooling system operates efficiently. 

Causes of a bad Door Switch can include mechanical wear from frequent use, electrical faults such as short circuits or burnt contacts, and physical damage from impact or mishandling of the refrigerator door.

Symptoms of a bad Door Switch include:

• The interior light not turning on when the door is opened or not turning off when the door is closed
• The refrigerator or freezer not cooling properly
• The light staying on continuously
• The cooling system running continuously or not running at all due to incorrect signals from the switch

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Surface Element is an OEM part for Whirlpool ranges. This part provides heat to the cooking surface, allowing for the preparation of food. 

Common causes of a bad surface element include electrical faults, physical damage from heavy cookware, or degradation from constant heating and cooling cycles.

Symptoms of a bad surface element include:

• Inconsistent or uneven heating
• The element not heating up at all
• Visible damage such as burns or breaks in the coil
• Sparking or unusual noises when the element is turned on

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Includes screws and wire connectors. For the complete terminal block kit use 279320.

This felt kit seals the gap between the dryer drum and bulkhead to maintain proper airflow and smooth, quiet rotation. Replacing a worn seal can reduce noise, help prevent snags, and restore consistent drying performance.

• Forms a drum-to-bulkhead seal to keep heated air in the proper airflow path
• Cushions drum movement to minimize scraping or squealing sounds
• Helps prevent clothing from catching at the drum edge
• Common signs of wear: frayed or missing felt, visible gaps, unusual noise, longer dry times

• Disconnect power; turn off gas supply if applicable
• Access the drum and bulkhead; support the drum during service
• Remove the old seal and any residue; install the new felt evenly around the circumference
• After reassembly, rotate the drum by hand to ensure smooth contact and proper alignment

The Natural Gas Spring is an OEM part for Whirlpool ranges. This part assists in regulating the flow and pressure of natural gas to the burners, ensuring consistent and safe operation. The spring helps maintain the correct pressure within the gas regulator, which is vital for efficient cooking performance.

Causes of a bad natural gas spring can include wear and tear from prolonged use, exposure to high temperatures, or contamination from particles within the gas line.  

Symptoms of a bad natural gas spring include:

• Inconsistent or weak burner flames
• Difficulty in lighting the burners or oven
• Irregular cooking temperatures
• Unusual noises or gas odors near the regulator

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Comes with jumper wire.

The Natural Gas Orifice is an OEM part for Whirlpool dryers. This part regulates the flow of natural gas to the burner, ensuring efficient and safe combustion for proper drying performance.

Causes of a bad natural gas orifice can include buildup of debris or lint, wear and tear over time, or damage from improper handling during maintenance.

Symptoms of a bad dryer natural gas orifice include:

• The dryer not heating up
• Inconsistent or weak flame in the burner
• Longer drying times than usual
• Unusual gas odors or hissing sounds

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This high-limit safety thermostat monitors temperature on the dryer's heater housing and opens the heating circuit if temperatures climb too high. It helps protect components from overheating and can restore safe, reliable heating when the original control has failed. What it does

• Monitors heater housing temperature and opens the circuit on overheat
• Acts as a safety backup for the heating system to prevent damage
• Failure symptoms can include: dryer runs but no heat, intermittent heat that stops mid-cycle, or the thermostat testing open at room temperature
• Repeat trips often indicate restricted airflow; check venting and lint buildup

• One high-limit thermostat

• Disconnect power; for gas models, also shut off the gas supply
• Note wire locations, remove the old thermostat from the heater housing, and transfer wires to the new part
• Mount the thermostat flush to the housing for proper sensing; secure with existing hardware
• Before reassembly, clear lint and ensure proper airflow through the lint screen, duct, and exterior vent

This gasket fits between the dishwasher's transition duct and its cover plate. It creates a tight barrier that helps keep wash water and steam contained, protecting the door cavity from moisture intrusion.

• Seals the joint between the transition duct and cover plate in the inner door vent path
• Helps prevent water or steam leakage from the vent area
• Replace if the seal is torn, deformed, brittle, missing, or leaking around the vent

• Disconnect power and turn off the water supply before servicing
• Remove the outer door panel to access the transition duct and cover plate
• Note the seal's orientation, remove the old gasket, and clean mating surfaces
• Seat the new seal evenly and reassemble; test a short cycle to check for leaks

This oven light lens gasket seals the lens to the oven liner, helping keep heat, steam, and grease out of the light housing. It maintains a secure fit for the lens and protects the bulb and wiring.

• Creates a heat-resistant seal between the light lens and oven cavity
• Helps block heat, steam, and grease from entering the light assembly
• Stabilizes the lens/retainer so the lens sits flush and secure
• Common signs of failure: torn/brittle gasket, lens feels loose, condensation or grease inside the lens, or scorching around the light opening

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove the lens retainer and lens to access the gasket; note orientation before removal
• Seat the new gasket evenly around the opening, then reinstall the lens and retainer without overtightening
• The lens sits flush and the seal is even after reassembly

The Broken Belt Switch Kit is an OEM replacement part for Whirlpool dryers. It is an assembly that includes a microswitch and bracket installed to monitor the dryer drum belt status. The broken belt switch plays an important safety role by automatically stopping the dryer if it detects the drum belt breaking or slipping off the motor pulley during a cycle. The kit includes a switch, actuator lever, screws, and wire terminals.

Causes of a bad broken belt switch can include wear and tear over time, electrical malfunctions, or physical damage from a broken belt or other internal issues. Ensuring the switch is functioning correctly is crucial for the safe and efficient operation of the dryer.

Symptoms of a broken or failing switch include: 

• The dryer failing to shut off if the belt breaks during operation
• Inability to diagnose belt issues through error code displays  
• Intermittent stopping or variance in belt tension detection

This genuine Whirlpool switch replacement is also compatible with Kenmore, Maytag, Jenn-Air, and KitchenAid dryer models.

This burner tube channels the gas-air mixture to the burner and includes an adjustable air shutter to set proper combustion. Replacing a damaged assembly helps restore reliable ignition, stable flame, and consistent heating performance.

• Directs the fuel/air mixture from the gas valve to the burner port
• Integrated adjustable shutter regulates primary air for proper flame
• Helps maintain efficient heat output and reliable burner operation
• Failure can present as no or intermittent heat, burner that lights then goes out, yellow/lazy flame, or soot

• Disconnect power and shut off the gas supply; allow the appliance to cool before servicing
• Access the burner compartment and transfer any clips/brackets from the original tube
• Note the current shutter position; after installation, adjust for a steady blue flame
• After reassembly, leak-test gas connections with a soap solution and verify burner operation

This genuine OEM replacement part is a burner and gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential function. If the dryer is no longer drying clothes effectively or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is a relatively simple job.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the burner and gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old burner assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

This stationary drying rack sits inside the dryer drum to dry items flat without tumbling. It replaces a missing or damaged rack so you can properly dry sweaters, shoes, and other items that shouldn't rotate in the drum. What it does:

• Provides a stable, non-rotating surface inside the drum for flat-drying
• Allows airflow to dry items that should not tumble (e.g., sweaters or shoes)
• Restores the dryer's rack-dry capability when the original rack is missing or broken
• Typical symptoms: rack is cracked/warped, won't sit securely, or you need to dry items flat

• 1 drying rack

• Unplug the dryer before installing
• Open the door and position the rack so the rear support engages at the back of the drum and the front rests in the door opening
• Ensure the rack is level and secure before loading items evenly
• Do not run standard tumbling cycles with the rack installed; remove it when finished

The Door Hinge is an OEM part for Whirlpool dryers. This hinge ensures the secure attachment of the dryer door to the appliance, allowing it to open and close smoothly. Right-hand hinge. For the left hinge use AP3047600

Causes of a bad door hinge can include regular wear and tear, accidental impacts, or overloading the door.

Symptoms of a bad door hinge include:

• Door not closing properly
• Door sagging or misaligned
• Difficulty opening or closing the door
• Noises or squeaking when moving the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.