Kitchenaid Ice Door Or Ice Chute

This ice maker cover shields the front of the ice maker assembly, protecting the module and moving parts from dust and accidental contact. Replacing a cracked or missing cover restores a clean, finished appearance and keeps components protected.

• Shields the ice maker's front components and control module
• Helps keep dust, splashes, and debris out of the mechanism
• Prevents accidental contact with moving ejector parts
• Replace if the cover is cracked, warped, missing, or will not stay attached

• Unplug the refrigerator before servicing
• Access the ice maker in the freezer compartment
• Carefully release the retaining tabs and remove the old cover; note orientation
• Align the new cover and press until it snaps securely into place—do not force the tabs

This replacement ice maker cover snaps over the icemaker assembly to shield moving parts and keep frost and debris out. Replacing a cracked or missing cover helps restore reliable ice production and a clean, finished look inside the freezer.

• Protects the ice maker's internal components from accidental contact and debris
• Helps reduce frost buildup around the ejector and motor area
• Maintains proper fit and clearance for smooth ice harvesting
• Common symptoms: cover cracked, broken tabs, loose or missing cover, excess frost around the icemaker

• Disconnect power to the refrigerator and turn off the water supply
• Remove the ice bin to access the ice maker
• Release any retaining tabs or screws and remove the old cover
• Install the new cover, ensuring the ejector and shutoff arm move freely; restore power and water

This ice maker cover fits over the ice maker head to protect the control module and moving parts inside your freezer. Replacing a cracked or missing cover helps prevent frost intrusion and restores a clean, finished look.

• Shields the ice maker mechanism from debris and moisture
• Helps maintain airflow to reduce frost at the ice maker face
• Replaces a cracked, warped, or missing cover with broken tabs
• Can help address exposed gears/wiring or rattling from a loose cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the front of the ice maker
• Release retaining tabs or screws and remove the old cover
• Align and snap the new cover fully into place; verify it's secure and clear of moving parts

The Ice Maker Scoop is an OEM component specifically designed for Whirlpool ice machines. As an included accessory, it provides a sanitary and convenient way for users to fetch ice from the storage bin.

The scoop is strategically designed with an ergonomic handle and wide opening bowl shape. This facilitates easy scooping and transport of ice cubes without spillage or crumbling. Its food-safe materials maintain hygienic conditions in the storage area. 

Symptoms of a faulty scoop include:

• Cracks or breaks that compromise the scooping surface 
• Leaks or spills of ice when trying to scoop
• Sharp edges that risk cuts or scratches
• Warping or loosening of the handle attachment over time

This OEM Whirlpool scoop is also compatible with some Scotsman and Manitowoc ice machines. Replace yours today to restore safe and hygienic ice retrieval from the storage bin.
 

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

Replacement ice dispenser door that restores proper ice chute coverage and helps prevent ice spillage and air leaks in compatible refrigerators. OEM-style fit keeps the dispenser operating cleanly and helps maintain freezer interior order. What it does:

• Covers the ice chute so cubes are directed into the dispenser, reducing spills and mess.
• Prevents drafts and helps limit frost buildup around the dispenser opening.
• Replaces cracked, warped, or stuck dispenser doors that interfere with ice delivery.
• Restores proper alignment so the dispenser lever and chute operate smoothly.

• Disconnect power to the appliance before accessing the dispenser area to avoid injury.
• Removal typically requires taking off the inner door trim or access panel; retain all fasteners for reinstallation.
• Handle edges carefully to avoid damage; verify proper alignment and dispenser function after installation.

This separator is a molded baffle that helps position and isolate internal components to ensure proper airflow and reliable operation. Replaces a worn or broken separator to restore correct internal alignment and reduce noise or rubbing. What it does:

• Keeps internal parts separated and secured to prevent contact or misalignment
• Directs or channels airflow where required for proper operation
• Helps reduce vibration noise caused by loose or shifted components
• Prevents chafing or rubbing that can lead to premature wear on nearby parts

• One separator/baffle as shown

• Refer to your model's exploded parts diagram for correct placement and orientation
• Disconnect power (and water, if applicable) before beginning repairs
• Use basic hand tools; avoid forcing the part into place to prevent damage
• If other plastic mounting tabs are damaged, inspect and replace those parts as needed

This replacement ice door is the dispenser flap that opens and closes to release ice from the freezer into the dispenser chute, restoring normal ice delivery and helping keep the dispenser sealed when idle. What it does:

• Replaces a cracked, warped, or broken dispenser/ice door that won't open or close properly
• Helps stop ice from jamming or falling into the dispenser area
• Restores the seal that keeps warm air out of the ice chute
• Works with the dispenser actuator to allow normal ice dispensing

• Disconnect power to the refrigerator before starting any work.
• Remove the dispenser housing trim per your model's service instructions to access the door; handle carefully to avoid damaging surrounding components.
• Inspect the actuator arm and mounting tabs during install; replace or realign if worn or broken.
• Test dispenser operation after installation to ensure the door opens and closes smoothly.

The Ice Scoop is an OEM part for Whirlpool refrigerators. This accessory is designed to make scooping ice from your refrigerator's ice bin easier. It features a comfortable handle and a well-designed scoop, allowing you to easily serve ice for your beverages or other cooling needs.

A bad ice scoop can occur due to wear and tear, damage, or loss. If you find yourself struggling to scoop ice or if your current ice scoop is damaged or missing, it's time to replace it with this genuine OEM part.

Symptoms of a bad ice scoop include:

• Difficulty in scooping ice
• Broken or cracked scoop
• Missing or lost ice scoop

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This ice guide directs ice from the freezer ice maker or bin into the dispenser chute to keep cubes flowing and reduce jams. It restores proper alignment so the dispenser delivers ice cleanly to the cup or container. What it does:

• Guides ice from the ice maker/bin into the dispenser chute for smooth delivery
• Helps prevent ice from catching on the chute or falling off-center
• Reduces noisy or irregular dispensing caused by misaligned ice flow
• Works with the ice-maker/dispenser assembly to maintain consistent dispensing

• One ice guide

• Turn off ice/dispenser functions and unplug power before starting work
• Handle gently to avoid cracking the plastic guide; align tabs with mounting points before snapping into place
• No special tools typically required; refer to appliance manual for access steps
• If ice continues to jam after replacement, inspect ice maker, bin, and chute for ice buildup or other damage

This funnel directs water into the ice maker fill cup to ensure proper filling and reduce spills. It helps maintain reliable ice production by guiding water flow to the correct inlet area. What it does:

• Directs incoming water into the ice maker's fill cup so the correct amount reaches the ice mold
• Reduces splashing and overflow during the fill cycle
• Helps prevent water from pooling inside the freezer compartment near the ice maker
• Supports consistent ice production when installed and aligned properly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove the ice maker or access panel as needed to reach the old funnel
• Align the replacement funnel with the mounting tabs and secure per OEM orientation; avoid forcing it into place
• Test fill cycle after installation and check for leaks; for detailed steps

This outer front panel replaces a worn, cracked or damaged front cover to restore the appliance's appearance and protect internal components. It matches OEM form and fit for an exact external repair. What it does

• Covers and protects internal components at the front of the appliance.
• Restores a finished appearance if the original front panel is dented, cracked or scratched.
• Helps keep lint, dust and debris away from internal parts behind the panel.
• Supports proper alignment of control and door openings (when applicable).

• One front cover (single outer front panel) as shown.

• Installation requires basic tools; remove power and disconnect appliance before starting.
• Support the cabinet or door while removing fasteners to avoid damage or injury.
• Retain and re-use any original screws, clips or gaskets unless replacements are supplied separately.