Need Help?
Call or text
Fixes broken or cracked detergent drawer that won't stay in place. Simple 5-minute replacement—just pull out old drawer and snap in new one.
Had to buy a new draw handle and detergent draw..they attach together by two plastic tabs that take a lot of stress each time you open it..unfortunately had to buy both to fix the problem.. Read more
Fix a washer that overfills, won't fill enough, or stops filling mid-cycle. This water level pressure switch regulates tub fill. DIY repair in 30 minutes.
At first, I thought, maybe I should just get a new washing machine. After all, it is almost 20 years old! I couldn't bring myself to do that and said to myself, let me see if I can figure out what parts I need and see if I can find a video that tells me how to do it and see how hard it is. I’ve never attempted appliance repair before. After figuring out what the most likely parts were, I ordered the water level switch and agitator cam repair kit - I figured for $10 more, I might as well... Read more
Fix a washer that hums but won't spin or agitate with this motor start capacitor. Repairs motor startup issues. Moderate DIY, 30-60 minutes.
Found the motor switch was fried. So replaced that and the capacitor. Starts fine now. Read more
Gasket for upper wheel.
With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more
Rear access cover panel for refrigerators. Shields compressor and electrical components from dust and debris. Replace if cracked, damaged, or worn.
My 16 year old son ordered the part and replaced the part. It took him less than 5 minutes to replace the part. Read more
Fix washer overfilling or won't fill issues with a new water level pressure switch. Prevents flooding and restores proper fill cycles. 10-minute DIY repair.
Replaced the water-level switch and hose. Washer works again, no overflowing since! Read more
The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
Routes wastewater from your washer to the household drain. Replace this hose if cracked, kinked, clogged, or leaking at connections to restore proper drainage.
Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ... Read more
Structural bracket that secures the rear panel to the washer chassis. Replace if cracked, broken, or missing to restore proper alignment and cabinet stability.
In the end, with a new coupler. But I relearned old lessons the hard way. The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned... Read more
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Replaced flow meter and control valve Read more
Directs defrost water from the evaporator to the drain pan. Replaces cracked, broken, or deformed drain tubes causing leaks or ice buildup issues.
A YouTube video: https://www.youtube.com/watch?v=jIdtNdDXFDk , by a professional appliance repair company described replacement of the freezer drain pipe with Kenmore's (by Whirlpool) revised drain pipe. Ice buildup inside the freezer was caused by warm air beneath the freezer contacting cold air from inside the freezer the resulting condensation freezing and blocking the drain, causing the ice buildup inside. The revised drain tube functions as a p-trap to prevent cold/warm air interaction.... Read more
Siphon break installs in the washer drain system. Replace if cracked, clogged with deposits, or leaking during fill cycles to restore proper function.
Spoke to your staff And we were both pretty well on the same page. I suggested to send a picture of it and she was able to locate it, gave me the name and part number. Read more
This lid switch is the washer's safety interlock. It detects when the lid is closed so the machine can agitate and spin, and cuts power when the lid is opened to stop operation and enhance user safety.
Was set to pull the trigger on a new washer since this one was 10+ years old. Broke a $25 lid switch fumbling to get the washer open before I found the appliancepros video library. Once I got things apart the right way I was able to diagnose the problem in 5 minutes. Identified the $10 part needed. Got the $10 coupling and the $25 switch and had the washer working like new in 20 minutes. I'm pretty proud of myself.. not going to tell anyone about the $25 switch. Read more
Rubber grommet for motor mount stud.
Replaced dog ears. Read more
Leaking from the water inlet connection? This vacuum break prevents backflow and maintains the air gap at the inlet. Easy DIY fix in under 30 minutes.
Removed cover from Whirlpool washer (~20 years old) and found water to be leaking from hose connection at Break Vac. Obviously the hose had to be replaced but the Break Vac looked corroded and partially plugged, too, possibly inhibiting water flow. While the cabinet was off I noticed the Suspension Spring was rusted off so I ordered 1 of those, too. Total of all parts was under $45 so looks like we won't be getting a newer, more efficient washer anytime soon. Everything arrived in 3 days and... Read more
Washer thrust ring acts as a bearing spacer between the outer tub and basket drive, controlling end-play and reducing friction. Replace when worn to restore smooth, quiet operation and prevent premature wear.
Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new. Read more