Lg Washer Parts

Mounts the door hinge to your washer's front cabinet. Replace if bracket is bent, broken, or missing to restore proper door alignment and sealing.

Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.

Seals the door opening on front-load washers to contain water during cycles. Replace if torn, deformed, or mildewed to restore a watertight seal.

Mounting bolt for washers. Secures internal components and assembly parts. Replace if bolt is stripped, corroded, missing, or damaged during repairs.

Connects water hose to washer nozzle/dispenser assembly. Replace if cracked, worn, or leaking to restore a tight, leak-resistant seal during fill cycles.

This kit includes the bushing components that fit into the door hinge assembly on a front-load washer. The bushings reduce friction and allow the door to pivot smoothly when opening and closing. Replace this kit if the washer door feels loose, sags, makes grinding or squeaking noises, or no longer aligns properly with the door latch.

Secures the door boot gasket in its groove to maintain a watertight seal. Replace if stretched, bent, or broken to stop front-panel leaks. Verify fit.

Comes in a pack of four.

Thermal fuse that protects the washer motor circuit from overheating. Interrupts power if motor temperature exceeds safe limits. Replace if washer stops mid-cycle or won't start.

This is an adjustable mounting bracket assembly used to secure a dryer to a laundry pedestal. It provides stable attachment and proper alignment between the dryer and the pedestal base. Replace this bracket if it is bent, broken, or missing, which can cause the dryer to shift or sit unevenly on the pedestal.

Fix washer slipping, grinding, or failure to spin with this clutch housing assembly. Secures clutch coupling to restore proper drive engagement.

Seals the door opening to the outer tub on front-load washers. Replace if you notice leaks, tears, odors, or clothes snagging. Confirm fit with your model.

Base bracket that holds the leveling foot at the washer cabinet. Replace if cracked, broken, or missing to restore stability and prevent rocking or vibration.

Flexible rubber seal around the door opening that prevents leaks during wash and spin cycles. Replace if torn, cracked, or moldy. Confirm fit with your washer model number.

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

This tub-to-pump hose connects the washer's outer tub to the drain pump, carrying water out during the drain cycle. Replace it to resolve leaks or drain errors caused by cracks, splits, or internal blockages.

• Routes wash water from the outer tub to the drain pump
• Flexible bellows section helps prevent kinking and accommodates tub movement
• Failure signs: water leaking under the washer, slow/no draining, drain-related error codes, or visible cracks/soft spots
• Often needed after clamp corrosion, physical damage, or age-related deterioration

• Unplug the washer and turn off water supply; drain any remaining water from the tub/hoses
• Access location varies by model; remove panels as needed to reach the hose and clamps
• Use pliers to release spring clamps; note routing and clamp orientation before removal
• Seat the hose fully on fittings, secure clamps, and test with a short drain/rinse cycle to check for leaks