Maytag Cooktop Parts

This door latch secures the appliance door and signals the control that it's safely closed. Replacing a worn or broken latch restores reliable door closure and proper cycle operation. What it does:

• Holds the door closed and aligned during use
• Engages the door strike to complete the door/lock switch circuit
• Resolve issues such as: door won't latch or pops open; cycles won't start; intermittent "door open" messages; needing to press/hold the door to run

• One door latch

• Disconnect power before servicing
• Access is typically from the door/front panel; note screw locations and latch orientation
• Transfer any mounting hardware from the original latch if needed
• After installation, verify smooth latch engagement with the strike and run a test cycle

This part is a grill element that is used on a cooktop. The element is responsible for supplying heat to the cooking area of the cooktop. If the element is not lighting up orange or red when it is turned on, it will need to be replaced. This part may need to be replaced over time due to normal wear and tear on the appliance. Some users may also notice that the element is not heating evenly or works intermittently. If this is the case, this is a genuine OEM replacement part that is made out of high-quality materials. Unplug the range from the electrical outlet and allow the cooktop ample time to cool down before trying to replace it. Wear work gloves for safety during this process.This part is compatible with cooktops that are manufactured by Jenn-Air and Maytag. It is sold individually and comes from the manufacturer.

This gas valve knob restores smooth burner control on your range or cooktop. Replace a cracked, stripped, or missing knob to reliably turn the valve from Off to Hi/Lo and fine-tune the flame.

• Mounts on the burner valve stem to select Off, Low, and High settings
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob won't turn the valve or align with settings
• Restores consistent feel and control during flame adjustment

• Ensure all burners are Off and the appliance is cool before servicing.
• Pull the old knob straight off the valve stem; do not force or twist the stem.
• Align the new knob with the flat/D of the stem and press firmly until fully seated.
• Disconnect power and shut off gas first if accessing internal parts is required.

This is a control knob for a range/cooktop. It lets you turn the burner valve shaft to adjust flame or heat settings. A worn or cracked knob can slip, sit crooked, or fail to turn the control smoothly.

• Replaces a damaged or stripped knob so settings engage properly
• Common symptoms: knob cracks, loosens, wobbles, or won't turn the valve shaft
• Restores clear pointer alignment and tactile click/feel during adjustment

• Disconnect power and allow all surfaces to cool before servicing
• Pull the old knob straight off the valve shaft; align the new knob's D-shape/flat with the shaft and press firmly
• Do not force—verify the knob matches the shaft style and location
• Test each control for smooth movement and correct alignment after installation

This surface-burner igniter switch mounts on the gas valve stem and signals the spark module when you turn the knob. Replacing a worn switch restores reliable top-burner ignition and helps eliminate intermittent or continuous clicking.

• Mounts on the surface burner gas valve and closes the circuit to the spark module as the knob is turned
• Triggers the igniter electrodes to spark so the burner lights
• Helps address: no spark when turning the knob, intermittent or delayed ignition, or continuous clicking/sparking
• Typical failure signs include needing to jiggle the knob to spark or sparking that won't stop after the flame is lit

• Disconnect electrical power; shut off gas supply if working near gas fittings; allow the appliance to cool
• Pull off the burner knob and remove the panel/top as needed to access the valve switch
• Move wires to the new switch one at a time to maintain correct connections; ensure the actuator aligns on the valve stem
• Reassemble, restore power, and test burner ignition

This adhesive-backed foam tape seals small gaps and cushions mating parts inside your appliance. Replacing worn or missing foam helps reduce noise and vibration while preventing air leaks and condensation that can lead to performance issues.

• Seals joints and gaps to help maintain proper airflow and temperature control
• Cushions panels and components to reduce rattles, buzzing, and vibration
• Helps prevent moisture intrusion that can cause condensation or frost
• Restores secure fit where original foam has compressed, torn, or fallen off

• Disconnect power (and water supply if applicable) before starting
• Remove all old foam/adhesive and clean surfaces; allow to dry fully
• Measure, cut to length, peel backing, and apply without stretching the tape
• Press firmly along the length for good adhesion; keep clear of moving parts and vents

This radiant element cartridge replaces the plug-in cooking module on modular electric cooktops. It restores a smooth, even-heating surface and installs by seating into the cooktop receptacle, bringing damaged or non-heating modules back to reliable service.

• Provides radiant heat beneath a glass-ceramic surface for everyday boiling, simmering, and frying
• Plugs into the cooktop's cartridge receptacle on modular electric units
• Restores performance when the existing cartridge is cracked, damaged, or not heating consistently
• Black finish matches black cooktop designs

• Disconnect power at the circuit breaker before servicing
• Allow the cooktop and old module to cool completely; handle glass carefully
• Lift the old cartridge straight up to disengage; align and fully seat the new cartridge in the receptacle
• Restore power and test all heat settings

This is the removable metal oven bottom for the lower oven cavity. It forms the floor above the heating components, protecting them from spills while providing a clean, even surface for baking and easier cleanup.

• Shields heating components beneath the lower-oven floor from drips and debris
• Provides a flat, durable surface inside the oven cavity
• Helps promote even heating and airflow within the oven
• Typical replacement reasons: warped or rusted panel, chipped/flaking enamel, persistent smoke/odors from burnt-on spills

• Disconnect power at the breaker and allow the oven to cool completely before service
• Remove oven racks for access
• Remove the mounting screws (often at the rear), then lift and slide the panel out
• Reinstall with existing hardware; ensure proper clearance from the heating element before restoring power

This control knob attaches to the control shaft and lets you select settings on your appliance. If the knob is cracked, stripped, or missing, replacing it restores smooth turning and accurate setting selection.

• Provides a secure grip to turn the control shaft and choose temperature, cycles, or levels
• Replaces knobs that are loose, cracked, or spin without turning the control
• Restores proper alignment of the pointer with the panel markings
• Helps resolve "won't stay on a setting" complaints caused by a stripped insert

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Pull the old knob straight off; transfer any adapter or clip if present
• Align the flat/spline opening with the shaft and press straight on—do not force
• The pointer lines up with the panel and test operation

The Burner Cap Set is an OEM part for Whirlpool ranges. This set includes multiple burner caps that fit over the surface burners to distribute heat evenly across the cookware.

A bad surface burner cap can occur due to wear and tear, damage, or buildup of food debris. If you notice symptoms such as uneven flame, slow heating, or difficulty in maintaining consistent temperatures, it may be time to replace the surface burner cap set.

Symptoms of a bad surface burner cap include:

• Uneven or weak flame
• Slow heating or difficulty in reaching desired temperatures
• Excessive gas consumption

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: Set of 4

The Top Burner is an OEM part for Whirlpool gas ranges. It supports the center surface burner, providing a stable and efficient heat source for your cooking needs. It ensures proper gas flow and distribution, allowing the burner to ignite and provide an even flame for cooking.

A bad burner base can occur due to various reasons, such as wear and tear, buildup of food debris or grease, or accidental damage. If you notice symptoms such as uneven flames, difficulty in lighting the burner, or a wobbly or unstable center burner, it may be time to replace the burner base.

Symptoms of a bad burner base include:

• Uneven flames
• Difficulty in lighting the burner
• Wobbly or unstable center burner

Restore the efficient cooking performance of your Whirlpool gas range by replacing the faulty or worn-out center surface burner base with this genuine OEM part.
This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement control knob restores a secure grip and positive feel when selecting settings on your appliance. It attaches to the control shaft so you can smoothly turn and set functions without slipping or wobbling.

• Engages the control shaft to adjust settings such as temperature, time, or function
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like spinning freely, falling off, or hard-to-turn controls
• Maintains accurate selection and a clean, finished look

• Disconnect power (and gas, if applicable) before servicing
• Pull the old knob straight off; inspect the control shaft for damage or wear
• Align the new knob with the shaft orientation (flat or D-shape as applicable) and press on until fully seated

This blower speed switch lets you select the blower/fan speed to restore proper airflow control in your appliance. It replaces a worn or faulty speed selector so the blower will respond correctly when you change settings. What it does:

• Controls the blower/fan speed so the appliance can run at selectable airflow levels
• Replaces a switch that is stuck, unresponsive, or only running at one speed
• Restores reliable electrical connection between the control circuit and blower motor
• Helps eliminate intermittent fan operation or loss of speed selection

• Disconnect power to the appliance before starting any repair.
• Verify wiring placement and retain original fasteners; wiring diagram for correct connections.
• Handle terminals carefully to avoid bending or damaging contacts.

Color: black. It measures about 2 inches in diameter.

Color: White. For biscuit use WP8522567, for black use WP8522566.

This oven bake burner is designed for Direct Spark Ignition (DSI) ranges. It channels gas from the bake orifice and distributes an even flame under the oven floor for consistent baking performance and reliable light-off during the bake cycle.

• Distributes gas through burner ports to create an even bake flame
• Works with the DSI spark electrode to ignite the bake flame
• Can address uneven or weak flame patterns and delayed ignition in bake

• Disconnect power and shut off gas; allow the oven to cool completely
• Remove the oven bottom and flame spreader to access the burner
• Transfer any reusable mounting hardware or shields from the original burner
• After reassembly, restore gas/power and leak-test any disturbed gas connections per local code