Maytag Tub Or Basket

The Balance Ring is an OEM part for Whirlpool washing machines. This part maintains the stability of the washer drum during the spin cycle. It contains liquid that helps balance the load, minimizing vibrations and noise while ensuring smooth operation.

Causes of a bad balance ring can include general wear and tear, exposure to heavy or unbalanced loads, or physical damage.

Symptoms of a bad balance ring include:

• Excessive shaking or vibrating during the spin cycle
• Loud banging noises
• Washer moving or walking during operation
• Uneven or off-balance loads

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is an inner tub basket intended for use with washing machines and combination washers and dryers. It is located inside the washing machine in the middle of the appliance. The inner tub basket is responsible for holding clothing during a washing cycle. It has an agitator in the middle and sides with holes so that water can leave when the tub is spinning. It is attached to the outer tub, which seals in the water.The inner tub basket can become damaged and cause loud noises, leak, or fail to drain. If this occurs, this component will need to be replaced. Basic tools will be needed for the process. Make sure the washing machine is unplugged for safety. The hoses will need to be removed before taking out the inner tub basket and replacing it with a new one. The inner tub basket is sold on an individual basis. It is an authentic OEM replacement part that is sourced directly from the manufacture. This part is compatible with washing machines and washer/dryer combination appliances made by Inglis, Estate, Admiral, Crosley, Roper, Magic Chef, Amana, KitchenAid, Maytag, Kenmore, and Whirlpool.

This part is a replacement outer tub. This part's intended use is to repair a broken or defective outer tub in washing machines.The outer tub fits over the spin basket and is what ensures that the machine doesn't leak during use by sealing in the water. If this part is broken, water may drip or leak, and thus the front tub should be immediately replaced. It's important that the appliance is unplugged before any attempt is made to replace this part. Work gloves are recommended for proper safety and protection.This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. This is an authentic OEM replacement part made of high-quality materials. This outer tub can be used with different models of washing machines that have been manufactured by Whirlpool, KitchenAid, Kenmore, Scotsman, and some other brands. It is sold individually.

This is a Whirlpool washer inner tub spin basket. The spin basket is the portion of the washing machine the clothes are held. This piece must operate efficiently for the items in the washer to be thoroughly cleaned. The main indicators of a damaged spin basket are the loss of the ability to spin or the washer making loud noises due to moving and rattling of the spin basket.Begin installing the new basket by unthreading the screws that fasten the top portion of the washer to the base. Tilt this back, and use a screwdriver to unfasten the clips that hold the top of the tub in place. Remove the fabric softener reservoir from the center of the basket. Use a socket to unbolt the agitator at the bottom of the tub. Once this is removed, reach down and lift out the old tub. Complete these instructions in reverse to install the new unit.This is a genuine OEM part sourced directly from the manufacturer. This product is compatible with Whirlpool, Amana, Roper, Kenmore, and Maytag appliances.

This outer tub is the main housing that supports and encloses the dryer drum and internal components, restoring correct drum alignment and airflow for safe, quiet operation. What it does

• Supports and centers the rotating drum to prevent rubbing and misalignment
• Forms the air pathway for proper drying and ventilation
• Protects internal components from lint and foreign objects
• Addresses symptoms like loud scraping/squealing, excessive vibration, or visible damage to the tub area

• One outer tub housing only

• Disconnect power (and gas, if applicable) before starting work
• Replacing this part requires drum removal and moderate disassembly; have appropriate tools and a second person to help with heavy components
• Inspect and replace seals, bearings, or fasteners as needed
• After reassembly, run a short test cycle to ensure alignment and proper airflow

Outer tub assembly includes: outer tub, tub seal, drive shaft and bearings. To rebuild the tub, order the bearing and tub seal kit W10435302 and the bearing installation tool W10447783. When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model.

This outer tub is the dishwasher's main outer wash tub shell that helps contain water and support internal components. Replacing a damaged outer tub restores the cabinet seal and helps stop leaks and moisture damage. What it does

• Houses and supports the inner tub, pump, and other internal components.
• Contains wash water to prevent leaks from reaching the cabinet or flooring.
• Helps maintain proper alignment for spray arms and seals to function.
• Commonly replaced when the tub is cracked, warped, or allowing water to escape.

• One outer tub.

• Disconnect power and water before starting; follow OEM disassembly steps for your model.
• Replacement typically requires removing the dishwasher door, control console, and interior components; keep fasteners organized.
• Inspect and replace gaskets, seals, and mounting hardware as needed for a watertight repair.

This outer tub is the large stationary tub that holds water for the washer and supports the inner wash basket. It restores a watertight enclosure and structural support so your washer can fill, agitate, and drain properly. What it does:

• Forms the watertight basin that contains wash water and directs it to the drain
• Supports the inner tub/basket and helps keep the basket aligned during cycles
• Prevents water from leaking into the cabinet when intact
• A cracked, warped, or corroded outer tub can cause visible leaks, loud or uneven operation, and washer shutdowns

• One outer tub

• Disconnect power and water supply before beginning any repair
• Drain remaining water and remove the washer top/lid and control panel as needed to access the tub
• Support or remove the inner tub/basket per service manual instructions to avoid damage during removal
• Inspect and replace related seals, gaskets, and clamps as needed

Note: Bearings are only available with the gearcase assembly.

This replacement silverware/cutlery basket holds utensils securely during dishwasher cycles to keep items organized and allow thorough cleaning. Durable molded plastic resists staining and lets water and detergent reach utensils for better wash performance. What it does

• Holds forks, knives and spoons in place so utensils don't fall through the lower rack
• Allows water and detergent to circulate around cutlery for improved cleaning
• Helps prevent scoring and nesting of utensils for more even washing
• Restores organization to the dishwasher's lower rack when the original basket is cracked or missing

• One replacement silverware/cutlery basket

• No special tools required; simply set the basket into the lower dishwasher rack
• Handle carefully to avoid sharp utensils during installation
• Follow dishwasher manufacturer's safety instructions and disconnect power if recommended before servicing

This is an outer tub for washing machines. The outer tub and holds the inner tub and makes sure water doesn't leak into the rest of the appliance. A damaged outer tub will often make loud noises and could cause leaks.When replacing the outer tub, make sure the washing machine is unplugged and the water supply is turned off. Remove the control panel before disassembling the washing machine to get access to the outer tub. Tap the drive block and disconnect the outer tub before pulling the hose free and removing the suspension springs. The new part can be installed in the new place before turning the power and water back on. This outer tub is made for use with washing machines and washer and dryer combination appliances made by Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Magic Chef, Admiral, Roper, Crosley, Inglis, and Estate. This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as a single part.

This balance ring mounts on the top of the washer's spin basket. Its sealed, liquid-filled chamber shifts weight to counterbalance uneven loads so the tub spins smoothly, reducing vibration, noise, and stress on other components. What it does:

• Uses internal fluid to counterbalance heavy or uneven loads during spin
• Helps minimize vibration, shaking, and thumping noises
• Reduces washer movement or "walking" during spin
• Common failure symptoms: excessive vibration/noise, frequent out-of-balance loads, or visible cracks/leaks at the ring

• 1 balance ring assembly

• Disconnect power and water; wear gloves and use proper safety precautions
• Access the ring by removing the cabinet/top and inner basket (procedure varies by model)
• Remove the old ring; seat the new ring evenly on the basket rim—do not puncture the sealed chamber
• Reassemble, level the washer, and run a test spin to ensure smooth operation

Includes ball bearing, rear bearing, water deflector, hose clamp, spacer, motor isolator, plug & Lip Seal

This outer tub is the main water containment housing for a top-load washer. It holds the wash basket and keeps water inside the machine so clothes get cleaned while protecting internal components from leaks and splashes. What it does:

• Contains the wash basket and holds wash water during fill and spin cycles.
• Supports and aligns the inner basket and related suspension components.
• Prevents water from reaching the cabinet and electrical components, reducing leak damage.
• Symptoms of a failing outer tub can include visible leaks, excessive vibration, or water pooling beneath the washer.

• One outer tub (single unit as shown)

• Disconnect power and water supply before starting any repair.
• Drain remaining water from the washer and remove the cabinet or access panels per your model's service instructions.
• Outer tub replacement typically requires transferring seals, bearings, and basket components; inspect and replace gaskets/parts as needed.

Kit Includes Front & Rear Outer Tubs with bearing Plus One Gasket. Bearings not available seperate.