Maytag Range / Cooktop / Oven Parts

Watched videos online and with that knowledge it was a very simple process. Read more

I first DISCONNECTED POWER FROM THE RANGE using the breaker. I then pulled the range out from the wall to give myself plenty of working room. I lifted the range top up as when you clean under the burners. I then moved the ends of the bottom of the slide rods that lock the range top open back where they came loose from the top of the range. This allows you to fold it higher and have complete access to the top of the range. I then took out all the Phillips head screws that hold down the sheet... Read more

I was just replacing my filter,on my vent. Read more

Ordered main control board and top blower. parts arrived as expected and well packaged. replaced main control board. Took two times to get ribbon cable inserted and aligned correctly. display functioned properly, but blower still not turning. replaced upper blower. everything working now. Read more

Purchased proper hinges. Lifted oven doors off the hinges. Removed screws securing the oven to the cabinet, then slid out the unit from the cabinet far enough to access the hinges. Then removed trim to better access the hinges. Then removed the screws holding the hinges. Then installed the new hinges, secured them with the screws, then reinstalled the trim, then slid the unit back into the cabinet, and secured it in place with the screws. Finally, I placed the oven doors back on my hinges. ... Read more

Ordered new handle from Appliance Parts Pro and replaced with the new handle. Read more

I was able to clean the Oven Temp Sensor with 99% alcohol. Then replaced All switches (after breaker was isolated). Put it all back the way I found it. Turned on breaker. Tested all functions and had no reports of Fan Code re-appearing since. Read more

Watched video from AppliancePartsPros.com, ordered part. I followed instructions on video and oven door works great now!!! Read more

So I ordered the burner and Ithe switch because I wasn't sure what part was defective. I pulled the oven out and I removed the 6 1/4 inch screws on each side of the glass top as well as the 2 Phillips head screws on the back, removing the 2 1/4 screws on the shield on the back gIves you easier access to them, then lifted the glass top up on the front to access the switch and burners. Make sure you turn the power off before beginning this process. When lifted up the wires connected to the... Read more

It was a simple process to enter the model number of our glass cook top stove; learn the part number required and order. It arrived in 2-days -- least expensive shipping method. The cooktop was removed with a Phillips-head screwdriver by 4 small sheet metal screws on the right and left side of the oven. The oven's power to the cooktop was easily disconnected via two "clips" and one ground. Would have cost way more with an appliance repair shop and it's an easy do-it-yourself repair. Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

• Element will not heat

I ordered 2 bake elements and bulbs and was able to easily fix 1 of the ovens. The serviceman who repaired the left oven did not repair it correctly so, one of the wires was not accessible so, I could only fix one oven. After shutting off the power, I EASILY fixed the right oven - with a LOT of care and a little elbow grease - in disconnecting the broken element, by doing exactly as it said to in the video, making certain not to allow the wires to slip back into the hole that it was pulled... Read more

I purchased the glass from Appliance Parts Pros.com and it came carefully packed in a few days. I was able to replace my glass without too much effort. Read more

Bought replacement relay board, replaced it. Would not work, turned stove circuit breaker off then on again. Display panel showed stove was resetting waited for reset, tested the bake option twice to ascertain it was working correctly. It worked! Our grateful appreciation to the customer service rep who helped us with our questions and the shipping. Wish we had gotten her name. Read more

• Element will not heat
• Little to no heat when baking
• Oven not heating evenly

Removed 2 sheet metal screw pulled element out about 2 inches. Removed two Spade connections. Removed the element from the oven. Inserted the new element into the over, connected the two spade connector. Reinstalled the two sheet metal screws. Set the oven to bake for testing and tested until the element turned red. Total time less than 5 minutes. Read more